Chaosexxtreme Ab en Um
-
Upload
enzo-ceballos -
Category
Documents
-
view
216 -
download
0
Transcript of Chaosexxtreme Ab en Um
-
8/13/2019 Chaosexxtreme Ab en Um
1/21
CONTENTS
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 1
U S E R S M A N U A L
2 Introduction
2 What is included?
3 Features
3 About 2 Ohm operation
4 General precautions
4 Installation precautions
4 Mounting the amplifier
5 Connecting the amplifier
6 Low level input wiring
9 High level input wiring
12 2CH Power and Speaker wiring2CH and Bridged Modes
13 2CH Power and Speaker wiringTriMode
14 4CH Power and Speaker wiring4CH and Bridged Modes
15 4CH Power and Speaker wiringTriMode
16 5CH Power and Speaker wiring5CH Mode
17 5CH Power and Speaker wiringBridged Mode
18 5CH Power and Speaker wiringTriMode
19 MonoBlock Power and Speaker wiring
20 Troubleshooting
21 Specifications
Congratulations on your
purchase of aCHAOS EXXTREME Amplifier.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making
your choice for car audio
entertainment!
page
CX250CX450CX550
CX750CX950CX1250
Two ChannelMOSFET Car AudioAmplifiers
CX600CX650CX800CX1000
Four ChannelMOSFET Car AudioAmplifiers
CX1800 Five ChannelMOSFET Car AudioAmplifier
CX1100MCX2000M
MonoBlockMOSFET Car AudioAmplifier
-
8/13/2019 Chaosexxtreme Ab en Um
2/21
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 2
Introduction
With the CHAOS EXXTREME
MOSFET amplifier series, we are
introducing eleven new amplifiers, all
designed in the USA. This new series
includes a two monoblock amps, six
2-channel, four 4-channel amplifiers
and a 5-channel amp.
All CHAOS EXXTREME models feature
variable low pass and high pass
crossovers and variable input gain
controls. They also incorporate an input
voltage sensistivity selector for added
system flexibility.
For further flexibility in the use of a
subwoofer, 0-+18dB Bass Boost
control has been included on all
amplifiers. You can control the
subwoofer level with the remote level
control module.
understands that amplifiers are
placed in many different kinds of
installations, so we incorporated a very
flexible system of controls in these
amplifiers in order to help you integrate
the amp into your system regardless
of the nature of your input source.
What is included?
When first unpacking your new
amplifier, please check first that the
package contains all of the items
below. If something is missing, contactthe store where you purchased the
amplifier.
CHAOS EXXTREME amplifier
Remote subwoofer level control
High input cable with connector
Four (4) mounting screws
-
8/13/2019 Chaosexxtreme Ab en Um
3/21
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 3
Features About 2 Ohm operation
Your new CHAOS EXXTREME amplifier
features the following:
Class A-B operation
Bridgeable outputs
(except CX1100M and CX2000M)
Tri-Mode capable
(except CX1100M and CX2000M)
MOSFET PWM (Pulse Width
Modulated) Power Supply
2 Ohm stable stereo operation
with output power increase
Thermal and speaker short
protection
Soft turn-on circuit
Remote turn-on/turn-off circuit
Variable input gain control
Variable low pass crossover(s)
Fixed high pass crossover(s)
Variable 0 to +18dB Bass Boost
Nickel-plated RCA low level and
high level inputs
LED power and protection
indicators
Silver anodized heatsink
Remote subwoofer level control
Your CHAOS EXXTREME amplifier
has been designed to operate
efficiently at loads down to 2 Ohms.
This means that you can install four8 Ohm speakers per channel, when
using parallel wiring.
Increasing the number of woofers per
channel at low frequencies (below
100Hz) produces an acoustic coupling
effect. This acoustic coupling effect
increases your power output by about
3dB per speaker, or the equivalent ofan additional 10W per speaker.
When operating at 2 Ohms, the
amplifiers will increase their output
power by approximately 50%. The
current draw will also increase by
about the same amount, so be sure
you have enough current to run the
amplifiers into a 2 Ohm load.
If you lack adequate current, your
music reproduction will be distorted.
-
8/13/2019 Chaosexxtreme Ab en Um
4/21
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 4
General precautions
SHOCK HAZARD! Do not open the caseof this product.There are dangerousvoltages present within the unit. There areno user-serviceable parts within the unit.
Before making or breaking power
connections in your system,
disconnect the vehicle battery. Confirm
that your head unit or other equipment
is turned off while connecting the input
jacks and speaker terminals.
If you need to replace the power fuse,
replace it only with a fuse identical to
that supplied with the amplifier. Using
a fuse of a different type or rating may
result in damage to your audio system
or your amplifier which is not covered
by the manufacturer's warranty.
Before installing and using your
new amplifier, please be-
come familiar with all the infor-
mation contained in this manual.
Please keep this manual in a safe
place for future reference.
Do not open or attempt to repair
this unit yourself. Dangerous high
voltages are present which may result
in electric shock. Refer any repairs to
a qualified service technician.
To avoid risk of electronic shock or
damage to the amplifier, do not permit
any of this equipment to become
damp or wet from water or drinks. If
this does occur, immediately unplug
the power wires and send the amplifier
to your local dealer or service center
as soon as possible.
If there is smoke or any peculiar
odor present during use or if there is
damage to any of the component
enclosures, immediately unplug the
power wire and send the amplifier to
your local dealer or service center as
soon as possible .
Installation precautions
Before you drill or cut any holes,
investigate your car's layout very
carefully. Take special care when you
work near the gas tank, fuel lines,
hydraulic lines and electrical wiring.
Never operate the amplifier when it is
unmounted. Attach all audio system
components securely to prevent
damage, especially in an accident.
Mounting the amplifier
1. Find a suitable location in the vehicle
in which to mount the amplifier.
2. Make sure there is sufficient air
circulation around the intended
mounting location.
3. Mark the location for the mounting
hole screws by positioning the amplifier
where you wish to install it. Use a
scribe or mounting screw, inserted
through each of the amp's mounting
holes, to mark the mounting surface.
If the mounting surface is carpeted,
measure the hole centers and mark
with a felt tip pen.
4. Drill pilot holes in the mounting
surface for the mounting screws. Place
the amplifier in position, and attach
the amplifier to the mounting surface
securely using screws.
-
8/13/2019 Chaosexxtreme Ab en Um
5/21
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 5
Before doing any wiring, look through
this manual and identify the diagrams
to follow for power, input and speaker
connections for your particular
installation. Be sure you understandall the connections before you proceed.
1. Connect the power ground terminal
to the closest point on the chassis of
the car. Keep this ground wire to less
than 39" (100 cm) in length. Use 8
gauge (or heavier) wire.
2. Connect the remote terminal to the
remote output of the head unit using
16 gauge (or heavier) wire.
3. Connect an empty fuse holder within
18" (45 cm) of the car battery, and run
8 gauge (or heavier) cable from this
fuse to the amplifier location.
4. Check that the fuse holder is empty.
Then connect the fuse holder to the
"BATT+" connection on the amplifier.
5. If multiple amplifiers are being used
in your system, either:
Run a separate pair of cables from
the battery and a chassis ground point
to each amplifier. Each (+) cable must
have its own inline fuse.
-or-
Run a #4 cable from the fuse holder
at the battery to a distribution block
at or near the amplifier's location. Then
run separate cables from the amplifier
to this distribution block and to
independent chassis ground points.
6. Connect all line inputs and outputs
(if used) using high-quality cables.
Connect all speakers, following the
diagrams in this manual. Be sure to
observe proper polarity to avoid audio
phase problems.
Connecting the amplifier
7. Insert fuse(s) into the battery fuse
holder(s).
8. Recheck all connections before
powering up the amplifier.
9. Set all level controls to minimum
position, and set all crossover
controls/switches to the desired
frequency points.
10. Power up the head unit and the
amplifier. Then set the volume control
on the head unit to about 3/4 volume,
and adjust the amplifiers input level
control(s) to just below the level of
distortion.
11. Further fine tuning of the various
controls may be necessary to obtain best
results.
Do not mistake the input level control
for a volume control! It is designed
ONLY to match the output level of
your audio source to the input level
of your amplifier.
Do not adjust this input level to
maximum unless your input level
requires it.
Ignoring these instructions will result
in an input overload to the amplifier,
and excessive audio distortion. It
can also cause the protection circuit
to engage.
Don't misuse the
level control!
-
8/13/2019 Chaosexxtreme Ab en Um
6/21
INPUTS
LOWLEVEL
HIGHLEVEL
CH3/4 CONTROLS
INPUTLEVEL
BASSBOOST
LOWPASSFREQ
100
40
35
145
155
160Hz0 + 12 dBMIN MAX
CROSSOVERMODE
HIGHPASSFULLRANGE
LOWPASSFREQ
100
40
35
145
155
160Hz
CROSSOVERMODE
FULLRANGE
CH1/2 CONTROLS
INPUTLEVEL
M I N M AX
POWER PROTECTION
CH
+2
CH
+1
CH
+4
CH
+3
1CH 2CH
3CH 4CH
REMOTESUBWOOFER
LEVELCONTROLF O U R C H A N N E LM O S F E T P O W E R A M P L I F I E R
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 6
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. Always use
a high-quality RCA cable for best audio performance.
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
2-Channel AmplifiersCX250, CX450, CX550,CX750, CX950, and CX1250
To AudioOutputs of head
unit or signalprocessor
CX600, CX650, CX800, and CX1000
4-Channel Amplifiers
To FRONT Audio Outputs of
head unit orsignal processor
To REAR Audio Outputs of
head unit orsignal processor
Remote SubwooferLevel Control
Remote SubwooferLevel Control
POWER PROTECTION
R +L+
INPUTS
LOWLEVELHIGHLEVEL
INPUTLEVEL
MI N MAX
BASSBOOST
0 +12dB
REMOTESUBWOOFERLEVELCONTROL
100
40
35
145
155
160
130
CROSSOVER
HIGHPASSFULLRANGE
LOWPASSLOWPASSFREQ,Hz MODE
LEFT RIGHT
T W O C H A N N E L M O S F E T P O W E R A M P L I F I E R
-
8/13/2019 Chaosexxtreme Ab en Um
7/21
SENSITIVITY
2-8V100mV-2V
LEVELINPUT CONTROLS CROSSOVER BASS BOOST
CH1/2 CONTROLS
MODEFREQ
LOWPASS
FULL
HIGHPASS
0 +18dB
45
90
Hz
CH3/4 CONTROLS
SENSITIVITY LEVELINPUT CONTROLS CROSSOVER BASS BOOST
M IN M AX
M IN M AX2-8V100mV-2V
45 90
Hz
FREQLOWPASS
HIGHPASS
0 +18dBFULL
MODE REMOTESUBWOOFERLEVELCONTROL
CH
+2CH
+1
CH
+4CH
+ 3HIGHLEVELINPUTS
LOWLEVELINPUTS
1CH 3CH
2CH 4CH
CH5 CONTROLSCH5INPUTS
5CH R
5CH L
SENSITIVITY
2-8V100mV-2V
LEVEL
INPUT CONTROLS
M IN M AX
5CH4CH
INPUT MODE BASSBOOST
0 + 18 dB
CROSSOVER
FREQ
LOWPASSFULL
45 90Hz
POWER
PROTECT
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 7
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. Always use
a high-quality RCA cable for best audio performance.
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
5-Channel AmplifierCX1800
To FRONT AudioOutputs of headunit or signalprocessor
To SUBWOOFERAudio Outputs ofhead unit or signalprocessor (if
present)
Remote SubwooferLevel Control
To REAR AudioOutputs of headunit or signalprocessor
-
8/13/2019 Chaosexxtreme Ab en Um
8/21
LOWPASSFREQUENCY
CROSSOVER
MODE
FULLRANGEINPUT CONTROLS
L EV EL SEN SI TI VI TY
INPUTS
LEFT RIGHT
BASS BOOSTREMOTESUBWOOFERLEVELCONTROL
POWER PROTECTION
0 +18dB
100
40
35
145
155
160 MI N MAX 2-8V 100mV-2VLOW LEVEL HIGHLEVEL
R+
L+
Hz
M O S F E T M O N O B L O C K P O W E R A M P L I F I E R
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 8
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. Always use
a high-quality RCA cable for best audio performance.
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
MonoBlock AmplifierCX1100M
CX2000M
MonoBlock Amplifier
To Audio Outputs of headunit orsignal processor
Remote SubwooferLevel Control
Remote SubwooferLevel Control
POWER PROTECTION
R +L+
INPUTS
LOW LEVELHIGHLEVEL
LEFT RIGHTINPUTLEVEL
MI N MAX
BASSBOOST
0 +12dB
CROSSOVERFREQUENCY
4 0H z 1 20 Hz
REMOTESUBWOOFERLEVELCONTROL
M O S F E T M O N O B L O C K P O W E R A M P L I F I E R
To Audio Outputs of headunit orsignal processor
-
8/13/2019 Chaosexxtreme Ab en Um
9/21
-
8/13/2019 Chaosexxtreme Ab en Um
10/21
SENSITIVITY
2-8V100mV-2V
LEVELINPUT CONTROLS CROSSOVER BASS BOOST
CH1/2 CONTROLS
MODEFREQ
LOWPASS
FULL
HIGHPASS
0 + 18 dB
45 90
Hz
CH3/4 CONTROLS
SENSITIVITY LEVEL
INPUT CONTROLS CROSSOVER BASS BOOST
M IN M AX
M IN M AX2-8V100mV-2V
45 90
Hz
FREQLOWPASS
HIGHPASS
0 + 18 dBFULL
MODE REMOTESUBWOOFERLEVELCONTROL
CH
+
2CH
+1
CH
+4
CH
+3HIGH
LEVELINPUTS
LOWLEVELINPUTS
1CH 3CH
2CH 4CH
CH5 CONTROLSCH5INPUTS
5CH R
5CH L
SENSITIVITY
2-8V100mV-2V
LEVELINPUT CONTROLS
M I N M AX
5CH4CH
INPUT MODE BASSBOOST
0 +18 dB
CROSSOVER
FREQ
LOWPASSFULL
45
90Hz
POWER
PROTECT
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 10
High Level Input Wiring
The high level input(s) should only be used when your head unit lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver
to the high level input connector of the amplifier. Be sure to observe polarity to
avoid audio phase problems.
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
5-Channel AmplifierCX1800 Remote
Subwoofer Level Control
To Speaker Terminalsof head unit
To Speaker Terminalsof head unit
CH3+ CH3- CH4- CH4+
CH1+ CH1- CH2- CH2+
-
8/13/2019 Chaosexxtreme Ab en Um
11/21
LOWPASSFREQUENCY
CROSSOVER
MODE
FULLRANGEINPUT CONTROLS
L EV EL SEN SI TI VI TY
INPUTS
LEFT RIGHT
BASS BOOSTREMOTESUBWOOFERLEVELCONTROL
POWER PROTECTION
0 +18dB
100
40
35
145
155
160 MIN MAX 2-8V 100mV-2VLOW LEVEL HIGHLEVEL
R+
L+
Hz
M O S F E T M O N O B L O C K P O W E R A M P L I F I E R
POWER PROTECTION
R +L+
INPUTS
LOW LEVELHIGHLEVEL
LEFT RIGHTINPUTLEVEL
MI N MAX
BASSBOOST
0 +12dB
CROSSOVERFREQUENCY
4 0H z 1 20 Hz
REMOTESUBWOOFERLEVELCONTROL
M O S F E T M O N O B L O C K P O W E R A M P L I F I E R
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 11
High Level Input Wiring
The high level input(s) should only be used when your head unit lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver
to the high level input connector of the amplifier. Be sure to observe polarity to
avoid audio phase problems.
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
CX2000M
MonoBlock Amplifier
To Speaker Terminalsof head unit
CX1100M
MonoBlock Amplifier
To Speaker Terminalsof head unit
Remote SubwooferLevel Control
RemoteSubwoofer Level Control
L- R+R-L+
L- R+R-L+
-
8/13/2019 Chaosexxtreme Ab en Um
12/21
GROUNDREMOTEBATT+
POWER CONNECTIONS
FUSE
R
SPEAKER CONNECTIONS
L
BRIDGED
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 12
Power and Speaker Wiring2 Channel and Bridged Modes
2-Channel Amplifiers
CX250, CX450, CX550,CX750, CX950, and CX1250
2-Channel Amplifiers
TwoChannelMode
SPEAKERIMPEDANCE
2-8 OHMS
Connect the Positive (+) terminal of thesubwoofer to the L (+) amplifier terminal.
Connect the Negative (-) terminal of thesubwoofer to the R (-) amplifier terminal.
BridgedMode
SPEAKERIMPEDANCE
4-8 OHMS
RIGHTSpeaker
+ LEFT Speaker
+
Subwoofer
+
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
GROUNDREMOTEBATT+
POWER CONNECTIONS
FUSE
R
SPEAKER CONNECTIONS
L
BRIDGED
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
-
8/13/2019 Chaosexxtreme Ab en Um
13/21
GROUNDREMOTEBATT+POWER CONNECTIONS
FUSE
R
SPEAKER CONNECTIONS
L
BRIDGED
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 13
Power and Speaker WiringTri-Mode
2-Channel Amplifiers
Tri-Mode
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus
a subwoofer on one pair of output channels. The main speakers will operate in STEREO
while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL position.Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown
below. Be sure to check the table at the bottom of this page to determine the correctcapacitor and inductor values for the crossover frequency you wish to achieve.
RIGHTSpeaker
LEFTSpeaker
2-Channel Amplifiers
CX250, CX450, CX550,CX750, CX950, and CX1250
Component values for6dB Passive Crossover
FREQUENCYINDUCTOR CAPACITOR
80 Hz100 Hz120 Hz150 Hz
7.5mH
6.5mH
5.5mH
4mH
470uF
330uF
330uF
220uF
SPEAKERIMPEDANCE
8 OHMS
Subwoofer
High pass filtercrossover
Low passfilter inductor
High pass filtercrossover
MINIMUMSPEAKER
IMPEDANCE4 OHMS
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
-
8/13/2019 Chaosexxtreme Ab en Um
14/21
GROUNDREMOTEBATT+
POWER CONNECTIONS
CH2
SPEAKER CONNECTIONS
CH1 CH4CH3
FUSES
BRIDGED BRIDGED
CH3/4CH1/2
GROUNDREMOTEBATT+
POWER CONNECTIONS
CH2
SPEAKER CONNECTIONS
CH1 CH4CH3
FUSES
BRIDGED BRIDGED
CH3/4CH1/2
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 14
Power and Speaker Wiring4 Channel and Bridged Modes CX600, CX650, CX800 and CX1000
4-Channel Amplifiers
FourChannelMode
SPEAKERIMPEDANCE
2-8 OHMS
SPEAKER
IMPEDANCE2-8 OHMS
BridgedMode
Connect the Negative (-) terminal of the RIGHT subwoofer tothe CH2 (-) amplifier terminal.
Connect the Positive (+) terminal of the RIGHT subwoofer tothe CH1 (+) amplifier terminal.
Connect the Negative (-)terminal of the LEFT
subwoofer to the CH4 (-)amplifier terminal.
Connect the Positive (+)terminal of the LEFT
subwoofer to the CH3 (+)amplifier terminal.
SPEAKERIMPEDANCE
4-8 OHMS
SPEAKERIMPEDANCE
4-8 OHMS
RIGHTSubwoofer
LEFT
Subwoofer
CH2Speaker
CH1 Speaker
CH4Speaker
CH3Speaker
to REMOTE TURN-ON
terminal of head unit
Chassisgroundpoint
BatteryFUSE
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
-
8/13/2019 Chaosexxtreme Ab en Um
15/21
GROUNDREMOTEBATT+
POWER CONNECTIONS
CH2
SPEAKER CONNECTIONS
CH1 CH4CH3
FUSES
BRIDGED BRIDGED
CH3/4CH1/2
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 15
Power and Speaker WiringTri-Mode CX600, CX650, CX800 and CX1000
4-Channel Amplifiers
Tri-Mode
Tri-mode operation allows you to connect this amplifier to a pair of main speakers
plus a subwoofer on one pair of output channels. The main speakers will operate
in STEREO while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL
position. Insert high pass filter capacitors and a low pass filter inductor into the
wiring as shown below. Be sure to check the table at the bottom of this page to
determine the correct capacitor and inductor values for the crossover frequency
you wish to achieve.
Component values for6dB Passive CrossoverFREQUENCYINDUCTOR CAPACITOR
80 Hz100 Hz120 Hz150 Hz
7.5mH6.5mH5.5mH4mH
470uF330uF330uF220uF
CH2Speaker
CH1Speaker
SPEAKERIMPEDANCE
8 OHMS
LEFTSubwoofer
+
+
High pass filtercrossover
Low passfilter inductor
High pass filtercrossover
MINIMUMSPEAKER
IMPEDANCE4 OHMS
CH3
Speaker
RIGHTSubwoofer
SPEAKERIMPEDANCE8 OHMS
MINIMUMSPEAKER
IMPEDANCE4 OHMS
Low passfilter inductor
High pass filtercrossover
CH4
Speaker
High pass filtercrossover
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
-
8/13/2019 Chaosexxtreme Ab en Um
16/21
CH2
CH1/2 BRIDGED
CH1
CH4CH3
CH5 GROUND REMOTE BATT+POWER CONNECTIONSFUSES
CH3/4BRIDGED
SPEAKERS
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 16
Power and Speaker Wiring5 Channel Mode CX1800
5-Channel Amplifier
CH5Subwoofer
FiveChannelMode
SPEAKERIMPEDANCE
2-8 OHMS
SPEAKERIMPEDANCE
2-8 OHMS
SPEAKERIMPEDANCE
2-8 OHMS
CH2Speaker
+
CH1 Speaker
+
CH4Speaker
CH3Speaker
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
-
8/13/2019 Chaosexxtreme Ab en Um
17/21
CH2
CH1/2 BRIDGED
CH1
CH4CH3
CH5 GROUND REMOTE BATT+POWER CONNECTIONSFUSES
CH3/4BRIDGED
SPEAKERS
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 17
Power and Speaker WiringBridged Mode CX1800
5-Channel Amplifier
BridgedMode
Connect the Negative (-) terminal of the RIGHTsubwoofer to the CH2 (-) amplifier terminal.
Connect the Positive (+) terminal of the RIGHTsubwoofer to the CH1 (+) amplifier terminal.
Connect the Negative (-) terminal of the LEFTsubwoofer to the CH4 (-) amplifier terminal.
Connect the Positive (+) terminal of the LEFTsubwoofer to the CH3 (+) amplifier terminal.
SPEAKERIMPEDANCE
4-8 OHMS
SPEAKERIMPEDANCE
4-8 OHMS
RIGHTSubwoofer
+
LEFTSubwoofer
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
CH5Subwoofer
SPEAKERIMPEDANCE
2-8 OHMS
-
8/13/2019 Chaosexxtreme Ab en Um
18/21
CH2
CH1/2 BRIDGED
CH1
CH4CH3
CH5 GROUND REMOTE BATT+POWER CONNECTIONSFUSES
CH3/4
BRIDGED
SPEAKERS
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 18
Power and Speaker WiringTri-Mode CX1800
5-Channel Amplifier
Tri-mode operation allows you to connect this amplifier to a pair of main speakers
plus a subwoofer on one pair of output channels. The main speakers will operate
in STEREO while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL
position. Insert high pass filter capacitors and a low pass filter inductor into the
wiring as shown below. Be sure to check the table at the bottom of this page to
determine the correct capacitor and inductor values for the crossover frequency
you wish to achieve.
Tri-Mode
CH4Speaker
CH3Speaker
Component values for
6dB Passive Crossover
FREQUENCYINDUCTOR CAPACITOR
80 Hz100 Hz120 Hz150 Hz
7.5mH6.5mH
5.5mH4mH
470uF330uF330uF220uF
SPEAKERIMPEDANCE
8 OHMS
CH1
Speaker
RIGHTSubwoofer
SPEAKERIMPEDANCE
8 OHMS
MINIMUMSPEAKER
IMPEDANCE4 OHMS
Low passfilter inductor
High pass filtercrossover
CH2Speaker
LEFTSubwoofer
+
+
High pass filtercrossover
Low passfilter inductor
High pass filtercrossover
MINIMUM
SPEAKERIMPEDANCE
4 OHMS
High pass filtercrossover
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
CH5Subwoofer
SPEAKERIMPEDANCE
2-8 OHMS
-
8/13/2019 Chaosexxtreme Ab en Um
19/21
GROUNDREMOTEBATT+
POWER CONNECTIONSFUSESSPEAKER
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 19
Power and Speaker WiringMonoBlock Mode CX1100M and CX2000M
Monoblock Amplifiers
MonoBlockMode
SPEAKERIMPEDANCE
2-8 OHMS
Speaker
+
to REMOTE TURN-ONterminal of head unit
Chassisgroundpoint
BatteryFUSE
-
8/13/2019 Chaosexxtreme Ab en Um
20/21
Troubleshooting
CHAOS EXXTREME MOSFET Amplifier Users Manual - page 20
If you experience operation or performance problems with this product, compare yourinstallation with the electrical wiring diagram on the previous pages. If problems persist,read the following troubleshooting tips which may help eliminate the problems.
Amplifier will notpower up.
Check to make sure you have a good ground connection.
Check that the Remote Input (Turn-On) has at least 3VDC.
Check that there is battery power on the (+) terminal.
Check that there is at least 12v.
Check all fuses, replace if necessary.
Make sure that the Protection LED is not illuminated. If it is lit, shut offthe amplifier briefly, and then repower it.
Protection LEDcomes on whenamplifier ispowered up.
Check for short circuits on speaker leads.
Turn down the volume control on the head unit to prevent overdriving.
Remove speaker leads, and reset the amplifier. If the Protection LED stillcomes on, then the amplifier is faulty and needs servicing.
No output. Check that all fuses are OK.
Check that amplifier is properly grounded.
Check that the Remote Input (Turn-On) has at least 3VDC.
Check that the RCA audio cables are plugged into the proper inputs.
Check all speaker wiring.
Low output. Reset the Level Control.
Check the Crossover Control settings.
Audio present inonly one channel.
Check the RCA interconnect cables.
Check all speaker wiring.
High hiss in thespeakers.
Disconnect all RCA inputs to the amplifiers. If the hiss disappears, thenplug in the component driving the amplifier and unplug its inputs. If thehiss disappears at this point, go on until the faulty/noisy component isfound.
It is best to set the amplifier's input level control as low as possible. Thebest subjective signal-to-noise ratio is achieved in this manner. Try to setthe head unit as high as possible (without distortion) and the amp input
level as low as possible.
Squealing noisefrom speakers.
Check for improperly grounded RCA interconnects.
Distorted sound. Check that the Input Level Control is set to match the signal level of thehead unit. Always try to set the Input Level as low as possible.
Check that all crossover frequencies are properly set.
Check for short circuits on the speaker leads.
Amplifier getsvery hot.
Check that the minimum speaker impedance for the amp model is correct.
Check that there is good air circulation around the amp. In some
applications, it may be necessary to add external cooling fan(s).
Engine noise(static type)
This is usually caused by poor quality RCA cables,which can pick upradiated noise. Use only the best quality cables, and route them awayfrom power cables.
Engine noise(alternatorwhine)
Check that speaker leads are not shorted to the vehicle chassis.
Check that the RCA grounds are not shorted to the vehicle chassis.
Check that the head unit is properly grounded.
SYMPTOM POSSIBLE REMEDY
-
8/13/2019 Chaosexxtreme Ab en Um
21/21
Specifications
All specifications subject to change without notice.
RMS POWERinto 4 Ohms
MAX POWERinto 2 Ohms
BRIDGED POWERinto 4 Ohms
Min. speakerimpedance
THD
Frequency response
Signal-to-noise ratio
Channel separation
Damping factor
Crossover rangelow pass
high pass
Bass boost
Fuse rating
Dimensions:(11-7/8" x 2-5/8" x ...)
MODEL
4-ChannelMOSFET Amplifiers
100W x 4
250W X 4
500W x 2
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
20A x 215-5/8"
CX650
RMS POWERinto 4 Ohms
MAX POWERinto 2 Ohms
BRIDGED POWERinto 4 Ohms
Min. speakerimpedance
THD
Frequency response
Signal-to-noise ratio
Channel separation
Damping factor
Crossover rangelow pass
high pass
Bass boost
Fuse rating
Dimensions:(11-7/8" x 2-5/8" x ...)
MODEL
2-Channe l MOSFET Ampli fiers
110W x 2
300W X 2
600W x 1
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A
10-9/16"
CX450
125W x 2
400W X 2
800W x 1
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A
12-3/16"
CX550
150W x 4
400W X 4
800W x 2
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A x 216-13/16"
CX800
220W x 2
800W X 2
1600W x 1
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
15A x 2
14-7/8"
CX750
300W x 2
1000W X 2
2000W x 1
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A x 2
16-13/16"
CX950
380W x 2
1250W X 2
2500W x 1
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
60A
19-3/8"
CX1250
200W x 4
500W X 4
1000W x 2
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
80A23-7/8"
CX1000
5-ChannelMOSFETAmpl ifier
250W x 1
1100W X 1
n/a
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A10-11/16"
CX1100M
120W x 4 +
300W X 4 +
600W x 2 +
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A x 320"
CX1800
600W x 1
MonoBlockMOSFETAmplifie rs
500W x 1
2000W X 1
n/a
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A x 216-13/16"
CX2000M
200W x 1
600W x 1
CX250
75W x 2
200W X 2
400W X 1
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
fixed, 200Hz
Variable 0 - +18dB
20A
7-7/8"
CX600
75W x 4
200W X 4
400W X 2
2 Ohm Stereo4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
fixed, 200Hz
Variable 0 - +18dB
20A x 213-3/8"