XG-MB67X Operation Manual · O CD-ROM fornecido contém instruções de operação em Inglês,...

MULTIMEDIA PROJECTORMODEL

XG-MB67XOPERATION MANUAL

Intro

du

ction

Qu

ick Start

Setu

pC

on

nectio

ns

Basic

Op

eration

Usefu

lF

eatures

Ap

pen

dix

XG-MB67X_EN2_CD__cover 06.5.12, 6:53 AM7

ii

IMPORTANT• For your assistance in reporting the loss

or theft of your Projector, please recordthe Model and Serial Number located onthe bottom of the projector and retain thisinformation.

• Before recycling the packaging, pleaseensure that you have checked the con-tents of the carton thoroughly against thelist of “Supplied accessories” on page 11.

Model No.:

Serial No.:

SPECIAL NOTE FOR USERS IN THE U.K.The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362fuse marked or and of the same rating as above, which is also indicated on the pinface of the plug, must be used.Always refit the fuse cover after replacing the fuse. Never use the plug without the fusecover fitted.In the unlikely event of the socket outlet in your home not being compatible with the plugsupplied, cut off the mains plug and fit an appropriate type.

DANGER:The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-ately and disposed of in a safe manner.Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socketoutlet, as a serious electric shock may occur.To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:THIS APPARATUS MUST BE EARTHED.IMPORTANT:The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : EarthBlue : NeutralBrown : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with thecoloured markings identifying the terminals in your plug proceed as follows:• The wire which is coloured green-and-yellow must be connected to the terminal in the

plug which is marked by the letter E or by the safety earth symbol or coloured green orgreen-and-yellow.

• The wire which is coloured blue must be connected to the terminal which is marked withthe letter N or coloured black.

• The wire which is coloured brown must be connected to the terminal which is marked withthe letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

XG-MB67X_EN2_CD_a 06.5.12, 6:38 AM2

iii

XG-MB67X_EN2_CD_a 06.5.12, 6:38 AM3

iv

The supplied CD-ROM contains operation instructions in English, German, French,Swedish, Spanish, Italian, Dutch, Portuguese, Chinese and Korean. Carefully readthrough the operation instructions before operating the projector.

Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch und Koreanisch.Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.

Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand,français, suédois, espagnol, italien, néerlandais, portugais, chinois et coréen. Veuillez lireattentivement ces instructions avant de faire fonctionner le projecteur.

Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska,franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska och koreanska.Läs noga igenom bruksanvisningen innan projektorn tas i bruk.

El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán,francés, sueco, español, italiano, holandés, portugués, chino y coreano. Leacuidadosamente las instrucciones de operación antes de utilizar el proyector.

Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese,svedese, spagnolo, italiano, olandese, portoghese, cinese e coreano. Leggereattentamente le istruzioni per l’uso prima di usare il proiettore.

De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds,Spaans, Italiaans, Nederlands, Portugees, Chinees en Koreaans. Lees de handleidingzorgvuldig door voor u de projector in gebruik neemt.

O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,Sueco, Espanhol, Italiano, Holandês, Português, Chinês e Coreano. Leiacuidadosamente todas as instruções de operação antes de operar o projetor.

XG-MB67X_EN2_CD_a 06.5.12, 6:38 AM4

1

Intro

du

ction

Before using the projector, please read this operation manual carefully.

There are two important reasons for prompt warranty registration of your new SHARPProjector, using the REGISTRATION CARD packed with the projector.

1. WARRANTYThis is to assure that you immediately receive the full benefit of the parts, serviceand labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACTTo ensure that you will promptly receive any safety notification of inspection,modification, or recall that SHARP may be required to give under the 1972Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT“LIMITED WARRANTY” CLAUSE.

WARNING: High brightness light source. Do not stare into the beam of light, or viewdirectly. Be especially careful that children do not stare directly into thebeam of light.

WARNING: To reduce the risk of fire or electric shock, do not exposethis product to rain or moisture.

WARNING: FCC Regulations state that any unauthorized changes or modifications tothis equipment not expressly approved by the manufacturer could voidthe user’s authority to operate this equipment.

The lightning flash with arrowhead sym-bol, within an equilateral triangle, is in-tended to alert the user to the presenceof uninsulated “dangerous voltage”within the product’s enclosure that maybe of sufficient magnitude to constitutea risk or electric shock to persons.

The exclamation point within a triangleis intended to alert the user to thepresence of important operating andmaintenance (servicing) instructions inthe literature accompanying the product.

Introduction ENGLISH

See bottom of projector.

U.S.A. ONLY

U.S.A. ONLY

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTIONRISK OF ELECTRIC SHOCK.DO NOT REMOVE SCREWSEXCEPT SPECIFIED USER

SERVICE SCREW.

INFORMATIONThis equipment has been tested and found to comply with the limits for a Class A digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment is operated in a commercialenvironment. This equipment generates, uses, and can radiate radio frequency energy and,if not installed and used in accordance with the operation manual, may cause harmfulinterference to radio communications. Operation of this equipment in a residential area islikely to cause harmful interference, in which case the user will be required to correct theinterference at his own expense. U.S.A. ONLY

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM1

2

Caution Concerning Lamp ReplacementSee “Replacing the Lamp” on page 55.

PRODUCT DISPOSALThis projector utilizes tin-lead solder, and a pressurized lamp containing a small amount ofmercury. Disposal of these materials may be regulated due to environmental considerations.For disposal or recycling information, please contact your local authorities or, if you arelocated in the United States of America, the Electronic Industries Alliance: www.eiae.org .

This SHARP projector uses a DMD panel. This very sophisticated panel contains 786,432 pixels(micromirrors). As with any high technology electronic equipment such as large screen TVs,video systems and video cameras, there are certain acceptable tolerances that the equipmentmust conform to.This unit has some inactive pixels within acceptable tolerances which may result in inactive dotson the picture screen. This will not affect the picture quality or the life expectancy of the unit.

WARNING:This is a Class A product. In a domestic environment this product may cause radiointerference in which case the user may be required to take adequate measures.

The enclosed computer cable must be used with the device. The cable is provided toensure that the device complies with FCC Class A verification. U.S.A. ONLY

WARNING:The cooling fan in this projector continues to run for about 90 seconds after the projector entersstandby mode. During normal operation, when putting the projector into standby mode alwaysuse the STANDBY/ON button on the projector or the STANDBY button on the remote control.Ensure the cooling fan has stopped before disconnecting the power cord.DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTINGTHE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM2

3

Intro

du

ction

40

Using the Menu Screen

Menu Selections (Adjustments)

Example: Adjusting “Bright”.• This operation can also be performed by using the buttons on the projector.

Press BMENU.• The “Picture” menu screen for the se-

lected input mode is displayed.

Adjustment buttons(P/R/O/Q)

Example: “Picture” screen menu for INPUT 1(RGB) mode

Press Q or O and select “Picture”to adjust.

1

2

ENTER button

RETURN button

Menu item

Picture ModeContrast 0

000K8 5 0 0

BrightRedBlue

1CLR TempBright BoostLamp Setting

Standard

BrightReset

SEL./ADJ. ENTER END

Picture SCR PRJ Net. Help

MENU/HELPbutton

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

• Press lRETURN toreturn to the previousscreen when the menuis displayed.

How to Read this Operation Manual

• In this operation manual, the illustration and the screen display are simplified for explanation, andmay differ slightly from the actual display.

Info ........Indicates safeguards for using the projector.

For Future Reference

Buttons used inthis operation

On-screendisplay

Button used inthis step

Note .........Indicates additional information for setting up and operating theprojector.

IndexMaintenance Troubleshooting

P. 64P. 52 PP. 59 and 60

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM3

4

Contents

Preparing

IntroductionHow to Read this Operation Manual .... 3Contents ............................................... 4IMPORTANT SAFEGUARDS ............... 6How to Access the PDF Operation

Manuals ............................................ 10Accessories ........................................ 11Part Names and Functions ................. 12

Inserting the Batteries .......................... 15Usable Range ...................................... 15

Quick StartQuick Start .......................................... 16

Using

Basic OperationTurning the Projector On/Off .............. 28

Turning the Projector on ....................... 28Turning the Power off (Putting the

Projector into Standby Mode) ........... 29Image Projection ................................. 30

About the Setup Guide ........................ 30Adjusting the Projected Image ............ 30Switching the Input Mode .................... 32Adjusting the Volume ........................... 32Displaying the Black Screen and Turning

off the Sound Temporarily ................. 32Correcting Trapezoidal Distortion ........ 33Resize Mode ......................................... 34

Useful FeaturesOperating with the Remote Control .... 36

Displaying and Setting the Break Timer .... 36Auto Sync (Auto Sync Adjustment) ..... 36Freezing a Moving Image .................... 36Selecting the Picture Mode .................. 36

Menu Items ......................................... 37Using the Menu Screen ...................... 40

Menu Selections (Adjustments) ........... 40Picture Adjustment (“Picture” menu) .. 42

Selecting the Picture Mode .................. 42Adjusting the Image ............................. 43Adjusting the Color Temperature ......... 43Progressive ........................................... 43Lamp Setting ........................................ 43

SetupSetting up the Projector ...................... 18

Setting up the Projector ....................... 18Standard Setup (Front Projection) ....... 18Ceiling-mount Setup ............................ 18Projection (PRJ) Mode ......................... 19Screen Size and Projection Distance .. 20

ConnectionsConnections ........................................ 21Samples of Cables for Connection ..... 22Connecting to a Computer ................. 23Connecting to Video Equipment ......... 24Connecting to a Monitor with RGB Input

Terminal ............................................ 25Controlling the Projector by a Computer .. 26Connecting the Power Cord ............... 27

Adjusting the Projected Image(“SCR - ADJ” menu) ......................... 44Setting the Resize Mode ...................... 44Adjusting the Image Position ............... 44Keystone Correction ............................ 44Setting the On-screen Display ............. 45Selecting the Background Image ........ 45Selecting the Setup Guide ................... 45Reversing/Inverting Projected Images ... 45Selecting the On-screen Display Language ... 45

Adjusting the Projector Function(“PRJ - ADJ” menu) .......................... 46Auto Search Function ........................... 46Auto Sync (Auto Sync Adjustment) ..... 46Auto Power Off Function ...................... 46Setting the Confirmation Sound

(System Sound) ................................. 46Speaker Setting .................................... 46Selecting the Transmission Speed (RS-232C) ... 47Fan Mode Setting ................................. 47Checking the Lamp Life Status ........... 47System Lock Function .......................... 47Locking the Operation Buttons on the

Projector (Keylock Function) ............. 48Setting up the Projector Network

Environment (“Network” menu) ........ 49Setting a Password .............................. 49DHCP Client Setting ............................. 50TCP/IP Setting ...................................... 50Confirming the Projector Information ... 50

Troubleshooting with the “Help” menu ...... 51Utilizing the “Help” menu functions ..... 51

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM4

5

Intro

du

ction

Reference

AppendixMaintenance ....................................... 52Maintenance Indicators ...................... 53Regarding the Lamp ........................... 55

Lamp ..................................................... 55Caution Concerning the Lamp ............ 55Replacing the Lamp ............................. 55Removing and Installing

the Lamp Unit .................................... 56Resetting the Lamp Timer .................... 57

Computer Compatibility Chart ............ 58Troubleshooting .................................. 59For SHARP Assistance ...................... 61Specifications ..................................... 62Dimensions ......................................... 63Index ................................................... 64

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM5

6

1. Read InstructionsAll the safety and operating instructions shouldbe read before the product is operated.

2. Retain InstructionsThe safety and operating instructions should beretained for future reference.

3. Heed WarningsAll warnings on the product and in the operatinginstructions should be adhered to.

4. Follow InstructionsAll operating and use instructions should befollowed.

5. CleaningUnplug this product from the wall outlet beforecleaning. Do not use liquid cleaners or aerosolcleaners. Use a damp cloth for cleaning.

6. AttachmentsDo not use attachments not recommended by theproduct manufacturer as they may cause hazards.

7. Water and MoistureDo not use this product near water–for example,near a bath tub, wash bowl, kitchen sink, orlaundry tub; in a wet basement; or near aswimming pool; and the like.

8. AccessoriesDo not place this product on an unstable cart,stand, tripod, bracket, or table. The product mayfall, causing serious injury to a child or adult, andserious damage to the product. Use only with acart, stand, tripod, bracket, or tablerecommended by the manufacturer, or sold withthe product. Any mounting of the product shouldfollow the manufacturer’s instructions, and shoulduse a mounting accessory recommended by themanufacturer.

9. TransportationA product and cartcombination should bemoved with care. Quickstops, excessive force,and uneven surfaces maycause the product and cartcombination to overturn.

IMPORTANT SAFEGUARDS

10. VentilationSlots and openings in the cabinet are providedfor ventilation to ensure reliable operation of theproduct and to protect it from overheating, andthese openings must not be blocked or covered.The openings should never be blocked by placingthe product on a bed, sofa, rug, or other similarsurface. This product should not be placed in abuilt-in installation such as a bookcase or rackunless proper ventilation is provided or themanufacturer’s instructions have been adheredto.

11. Power SourcesThis product should be operated only from thetype of power source indicated on the markinglabel. If you are not sure of the type of powersupply to your home, consult your product dealeror local power company. For products intendedto operate from battery power, or other sources,refer to the operating instructions.

12. Grounding or PolarizationThis product is provided with one of the followingtypes of plugs. If the plug should fail to fit into thepower outlet, please contact your electrician.Do not defeat the safety purpose of the plug.a. Two-wire type (mains) plug.b. Three-wire grounding type (mains) plug with

a grounding terminal.This plug will only fit into a grounding typepower outlet.

13. Power-Cord ProtectionPower-supply cords should be routed so that theyare not likely to be walked on or pinched by itemsplaced upon or against them, paying particularattention to cords at plugs, conveniencereceptacles, and the point where they exit fromthe product.

14. LightningFor added protection for this product during alightning storm, or when it is left unattended andunused for long periods of time, unplug it fromthe wall outlet and disconnect the cable system.This will prevent damage to the product due tolightning and power-line surges.

CAUTION: Please read all of these instructions before you operate this productand save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineeredand manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT INPOTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat thesafeguards incorporated in this product, observe the following basic rules for its installation,use and servicing.

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM6

7

Intro

du

ction

15. OverloadingDo not overload wall outlets, extension cords, orintegral convenience receptacles as this canresult in a risk of fire or electric shock.

16. Object and Liquid EntryNever push objects of any kind into this productthrough openings as they may touch dangerousvoltage points or short-out parts that could resultin a fire or electric shock. Never spill liquid of anykind on the product.

17. ServicingDo not attempt to service this product yourself asopening or removing covers may expose you todangerous voltage or other hazards. Refer allservicing to qualified service personnel.

18. Damage Requiring ServiceUnplug this product from the wall outlet and referservicing to qualified service personnel under thefollowing conditions:a. When the power-supply cord or plug is

damaged.b. If liquid has been spilled, or objects have fallen

into the product.c. If the product has been exposed to rain or

water.d. If the product does not operate normally by

following the operating instructions. Adjust onlythose controls that are covered by theoperating instructions, as an improperadjustment of other controls may result indamage and will often require extensive workby a qualified technician to restore the productto normal operation.

e. If the product has been dropped or damagedin any way.

f. When the product exhibits a distinct changein performance, this indicates a need forservice.

• DLP® and the DLP logo are registered trademarks of Texas Instruments.• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United

States and/or other countries.• PC/AT is a registered trademark of International Business Machines Corporation in the

United States.• Adobe® Reader® is a trademark of Adobe Systems Incorporated.• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or

other countries.• All other company or product names are trademarks or registered trademarks of their

respective companies.• Some IC chips in this product include confidential and/or trade secret property belonging

to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,reverse engineer, reverse assemble or discompile the contents thereof.

19. Replacement PartsWhen replacement parts are required, be surethe service technician has used replacementparts specified by the manufacturer or have thesame characteristics as the original part.Unauthorized substitutions may result in fire,electric shock, or other hazards.

20. Safety CheckUpon completion of any service or repairs to thisproduct, ask the service technician to performsafety checks to determine that the product is inproper operating condition.

21. Wall or Ceiling MountingThis product should be mounted to a wall orceiling only as recommended by themanufacturer.

22. HeatThis product should be situated away from heatsources such as radiators, heat registers, stoves,or other products (including amplifiers) thatproduce heat.

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM7

8

Observe the following safeguards when setting up yourprojector.Caution concerning the lamp unit Potential hazard of glass par-

ticles if lamp ruptures. Incase of lamp rupture, contactyour nearest Sharp Autho-rized Projector Dealer or Ser-vice Center for replacement.See “Replacing the Lamp” onpage 55.

Caution concerning the setup of the pro-jector For minimal servicing and to maintain high

image quality, SHARP recommends that thisprojector be installed in an area free fromhumidity, dust and cigarette smoke. When theprojector is subjected to these environments,the vents and lens must be cleaned more of-ten. As long as the projector is regularlycleaned, use in these environments will notreduce the overall operation life of the unit.Internal cleaning should only be performedby a Sharp Authorized Projector Dealer orService Center.

Do not set up the projector in places ex-posed to direct sunlight or bright light. Position the screen so that it is not in direct

sunlight or room light. Light falling directly onthe screen washes out the colors, makingviewing difficult. Close the curtains and dimthe lights when setting up the screen in asunny or bright room.

Caution regarding placing of the projec-tor Place the projector on a level site within the

adjustment range (8 degrees) of the adjust-ment foot.

After the projector is purchased, a faint smellfrom the vent may appear when the power isfirst turned on. This is normal and is not amalfunction. It will disappear after the projec-tor is used for a while.

When using the projector in high-altitudeareas such as mountains (at altitudes ofapproximately 1,500 meters (4,900 feet)or more) When you use the projector in high-altitude

areas with thin air, set “Fan Mode” to “High”.Neglecting this can affect the longevity of theoptical system.

Warning about placing the projector ina high position When placing the projector in a high position,

ensure that it is secured carefully to avoid per-sonal injury caused by the projector fallingdown.

Do not subject the projector to hard im-pact and/or vibration. Protect the lens so as not to hit or damage

the surface of the lens.

Rest your eyes occasionally. Continuously watching the screen for long

hours will cause eye strain. Be sure to occa-sionally rest your eyes.

Avoid locations with extremes of tem-perature. The operating temperature of the projector is

from 41°F to 95°F (+5°C to +35°C). The storage temperature of the projector is

from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intakevents. Allow at least 11 13/16 inches (30 cm) of space

between the exhaust vent and the nearestwall or obstruction.

Be sure that the intake vent and the exhaustvent are not obstructed.

If the cooling fan becomes obstructed, a pro-tection circuit will automatically put the pro-jector into standby mode to prevent overheatdamage. This does not indicate a malfunc-tion. (See pages 53 and 54.) Remove the pro-jector power cord from the wall outlet and waitat least 10 minutes. Place the projector wherethe intake and exhaust vents are not blocked,plug the power cord back in and turn on theprojector. This will return the projector to thenormal operating condition.

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM8

9

Intro

du

ction

When turning off the projector, the cooling fanruns to decrease the internal temperature fora while. Unplug the power cord after the cool-ing fan stops. The period the cooling fan runswill vary, depending on the circumstances andthe internal temperature.

Caution regarding usage of the projector When using the projector, be sure not to sub-

ject it to hard impact and/or vibration, as thiscan result in damage. Take extra care withthe lens. Before moving the projector, be sureto unplug the power cord from the wall outlet,and disconnect any other cables connectedto it.

Do not carry the projector by holding the lens. When storing the projector, re-attach the lens

cap. (See page 12). Do not expose the projector to direct sunlight

or place next to heat sources. Doing so mayaffect the cabinet color or cause deformationof the plastic cover.

Other connected equipment When connecting a computer or other audio-

visual equipment to the projector, make theconnections AFTER unplugging the powercord of the projector from the AC outlet andturning off the equipment to be connected.

Please read the operation manuals of the pro-jector and the equipment to be connected forinstructions on how to make the connections.

Info• The cooling fan regulates the internal tem-

perature, and its performance is automaticallycontrolled. The sound of the fan may changeduring projector operation due to changes inthe fan speed. This does not indicate malfunc-tion.

• Do not unplug the power cord during projec-tion or cooling fan operation. This can causedamage due to rise in internal temperature,as the cooling fan also stops.

Using the projector in other countries The power supply voltage and the shape of

the plug may vary depending on the regionor country you are using the projector in.When using the projector overseas, be sureto use an appropriate power cord for the coun-try you are in.

Temperature monitor function

If the projector starts to overheat due to setupproblems or blockage of the air vents, “ ” and“ ” will illuminate in the lower left cornerof the picture. If the temperature continues torise, the lamp will turn off, the temperature warn-ing indicator on the projector will blink, and aftera 90-second cooling-off period the projector willenter standby mode. Refer to “Maintenance In-dicators” on page 53 for details.

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM9

10

PDF operation manuals in several languages are included in the CD-ROM. To uti-lize these manuals, you need to install Adobe® Reader® on your computer (Win-dows® or Macintosh®).

Please download Adobe® Reader® from the Internet (http://www.adobe.com).

Accessing the PDF Manuals

How to Access the PDF Operation Manuals

• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first,then specify the desired file using the “File”, “Open” menu.

Note

For Windows®:1 Insert the CD-ROM in the CD-ROM drive.2 Double click the “My Computer” icon.3 Double click the “CD-ROM” drive.4 When you want to view the operation

manual1) Double click the “MANUALS” folder.2) Double click the language (name of the

folder) that you want to view.3) Double click the “MB67_” pdf file to ac-

cess the projector manuals.When you want to view the SETUPMANUAL1) Double click the “SETUP” folder.2) Double click the language (name of the

folder) that you want to view.3) Double click the “MB67_S” pdf file to ac-

cess the SETUP MANUAL.

For Macintosh®:1 Insert the CD-ROM in the CD-ROM drive.2 Double click the “CD-ROM” icon.3 When you want to view the operation

manual1) Double click the “MANUALS” folder.2) Double click the language (name of the

folder) that you want to view.3) Double click the “MB67_” pdf file to ac-

cess the projector manuals.When you want to view the SETUPMANUAL1) Double click the “SETUP” folder.2) Double click the language (name of the

folder) that you want to view.3) Double click the “MB67_S” pdf file to ac-

cess the SETUP MANUAL.

SETUP MANUALRefer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.

Connecting Pin Assignments .................................................. 2RS-232C Specifications and Commands ................................ 3Setting up the Projector Network Environment ....................... 7Controlling the Projector via LAN .......................................... 13Setting up the Projector Using RS-232C or Telnet ............... 18Troubleshooting ..................................................................... 28

XG-MB67X_EN2_CD_b 06.5.12, 6:39 AM10

11

Intro

du

ction

Accessories

Remote controlRRMCGA398WJSA

Two R-6 batteries (“AA” size, UM/SUM-3,

HP-7 or similar)

Power cord*

RGB cable(10' (3.0 m))

QCNWGA045WJPZ

• Operation manual (this manual (TINS-C517WJZZ) and CD-ROM (UDSKAA078WJZZ))

Optional accessories

Dust filter 3 RCA to 15-pin D-sub cable (10n (3.0 m)) Remote receiver Lamp unit

AN-DF1AN-C3CP2AN-MR2AN-XR20LP

Supplied accessories

For U.S. andCanada, etc.(6' (1.8 m))

QACCDA007WJPZ

For Europe,except U.K.(6' (1.8 m))

QACCVA011WJPZ

For U.K. andSingapore(6' (1.8 m))

QACCBA036WJPZ

For Australia, NewZealand and Oceania

(6' (1.8 m))QACCLA018WJPZ

(1) (2) (3) (4)

* Use the power cord that corresponds to the wall outlet in your country.

• Some of the optional accessories may not be available depending on the region. Please check withyour nearest Sharp Authorized Projector Dealer or Service Center.

Note

Lens cap (attached)CCAPHA024WJSA

DIN-D-sub RS-232C adaptor(5 57/64" (15 cm))

QCNWGA015WJPZ

XG-MB67X_EN2_CD_c 06.5.24, 1:51 PM11

12

33

40

53

32

32

30

31

52

30

15

28, 53

40, 51

29, 53

28, 29

40

Top View

STANDBY/ON buttonFor turning thepower on andputting theprojector intostandbymode.

Lamp indicator

Temperature warningindicator

Adjustment buttons(P/R/O/Q)For selecting menu items.

Volume buttons(–O/Q+)For adjusting the speakersound level.

ENTER buttonFor settingitems selectedor adjusted onthe menu. MENU/HELP button

For displayingadjustment andsetting screens, andhelp screen.

Front View

Focus ringFor adjustingthe focus.

INPUT button (P/R)For switching input mode1, 2, 3 or 4.

Remote controlsensor

HEIGHTADJUSTlever

Numbers in Z refer to the main pages in this operation manual where the topicis explained.

Part Names and Functions

Projector

KEYSTONEbuttonFor enteringthe KeystoneCorrectionmode.

Intake vent

Powerindicator

Zoom ringFor enlarging/reducing the picture.

Push both sides of the lens capto attach or remove.

XG-MB67X_EN2_CD_c 06.5.12, 6:40 AM12

13

Intro

du

ction

25

52

31

26

25

25 24

232425 27

21

2324

27

24

46

52


Terminals

Rear View

Refer to “INPUT Terminals and Connectable Main Equipment” on page 21.

AUDIO (INPUT3, 4) terminal(Shared forINPUT 3 and 4)

INPUT 3 terminalTerminal for connect-ing video equipmentwith an S-videoterminal.

INPUT 4 terminalTerminal forconnecting videoequipment.

Speaker

Rear adjustmentfoot

Kensington SecurityStandard connectorAC socket

Connect the suppliedPower cord.

Using the Kensington Lock• This projector has a Kensington Security Standard connector for use with a Kensington

MicroSaver Security System. Refer to the information that came with the system forinstructions on how to use it to secure the projector.

AUDIO OUTPUTterminalAudio output terminal ofequipment connected to theAUDIO INPUT terminal.

Intake vent

AUDIO (INPUT 1, 2)terminal (Shared forINPUT 1 and 2)

INPUT 1 andINPUT 2 terminalsTerminals forcomputer RGBand componentsignals.

OUTPUT (INPUT 1, 2)terminal(Shared computer RGB and componentsignals output terminal for INPUT 1 and 2)Terminal for connecting a monitor.

RS-232CterminalTerminal forcontrolling theprojector usinga computer.

Exhaust vent

LAN terminalTerminal forcontrolling theprojector usinga computer vianetwork.

XG-MB67X_EN2_CD_c 06.5.12, 6:40 AM13

14

33

40

32

36

32

4051

29 28

40

36

36

40

32

36

34


STANDBY buttonFor putting theprojector into thestandby mode.

KEYSTONE buttonFor entering theKeystone Correctionmode.

RETURN buttonFor returning to theprevious menu screenduring menu operations.

FORWARD/BACKbuttonsSame function as the[Page Down] and [PageUp] keys on a computerkeyboard when using theoptional Remote Receiver(AN-MR2).

BREAK TIMERbuttonFor displaying thebreak time.

AV MUTE buttonFor temporarilydisplaying a blackscreen and turningoff the sound.

PICTURE MODEbuttonFor selecting theappropriate picture.

ON buttonFor turning the power on.

Adjustment buttons(P/R/O/Q)• For selecting menu items.• For adjusting the Keystone

Correction when in theKeystone Correction mode.

MENU/HELP buttonFor displaying adjustmentand setting screens, andhelp screen.

ENTER buttonFor setting items selectedor adjusted on the menu.

RESIZE buttonFor switching the screensize (NORMAL,BORDER, etc.).

FREEZE buttonFor freezing images.

INPUT 1, 2, 3 and 4buttonsFor switching to therespective input modes.

Volume buttonsFor adjusting thespeaker sound level.

AUTO SYNC buttonFor automatically adjustingimages when connectedto a computer.

Part Names and Functions (Continued)

XG-MB67X_EN2_CD_d 06.5.12, 6:41 AM14

15

Intro

du

ction

• Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.

• Insert the batteries making sure the polarities correctly match the m and n marks inside the batterycompartment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.• Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.• Remove the batteries from the remote control once they have run out, as leaving them in can cause them

to leak.Battery fluid from leaked batteries is harmful to skin, therefore ensure that you first wipe them and thenremove them using a cloth.

• The batteries included with this projector may run down in a short period, depending on how they are kept.Be sure to replace them as soon as possible with new batteries.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

Incorrect use of the batteries may cause them to leak or explode. Pleasefollow the precautions below.

Inserting the Batteries

Attach the cover and slide it until it clicks into place.

Insert the batteries.• Insert the batteries making sure the polarities correctly match

the m and n marks inside the battery compartment.

Press the P mark on the cover and slide it in thedirection of the arrow.

1

2

3

Caution

• The signal from the remote control can be re-flected off a screen for easy operation. How-ever, the effective distance of the signal maydiffer depending on the screen material.

When using the remote control• Ensure that you do not drop it or expose it to

moisture or high temperature.• The remote control may malfunction under a

fluorescent lamp. In this case, move the pro-jector away from the fluorescent lamp.

Usable RangeThe remote control can be used to control theprojector within the ranges shown in the illustra-tion.

Remote control sensor

Remotecontrol signaltransmitters

Remote control

23n (7 m)30°

30°

Note

XG-MB67X_EN2_CD_d 06.5.12, 6:41 AM15

16

Quick Start

This section shows the basic operation (projector connecting with the computer). For details, seethe page described below for each step.

Setup and ProjectionIn this section, connection of the projector and the computer is explained using one example.

When connecting equipment other than a computer, seepages 24 and 25.

3. Remove the lens cap and turn the projector on

2. Connect the projector to the computer and plug the power cordinto the AC socket of the projector

On the projector On the remote control

KEYSTONE button

INPUT button

STANDBY/ONbutton

HEIGHTADJUST lever

Focus ring

STANDBY button

_PP. 21–27

_P. 28

ENTER button

ENTER button

6

4

3

7

8

3

7

6

8

KEYSTONEbutton

4

4

ON button

INPUT 1 button

4

1. Place the projector facing a wall or a screen _P. 18

XG-MB67X_EN2_CD_e 06.5.24, 1:52 PM16

17

Qu

ick Start

4. Adjust the projected image with the Setup Guide

Select the “INPUT 1” using the INPUT button on the projector or C INPUT 1 on the remotecontrol.

6. Select the INPUT mode

• When pressing the INPUT button on the projector, input mode switches in the followingorder: INPUT1 INPUT2 INPUT3 INPUT4

• When using the remote control, press the CINPUT 1/CINPUT 2/DINPUT 3/EINPUT4 button to switch the INPUT mode.

On theprojector

On the remotecontrol

On-screen display (RGB)

_P. 32

_P. 30

1 After the projector turns on, the Setup Guide appears. (When “Setup Guide” is set to “On”. npage 45)

2 Follow the steps in the Setup Guide and adjust the focus, screen size, and height (angle).

3 After adjusting the focus, height (angle) and screen size, press TENTER to finish the SetupGuide.

Correcting trapezoidal distortion using Keystone Correction.

7. Correct trapezoidal distortion

_P. 33

On the projector

On the remote control

Shrinksupper side.

Shrinkslower side.

5. Turn the computer on

8. Turn the Power offPress the STANDBY/ON button on the projector or the STANDBY button on the remote control,and then press the button again while the confirmation message is displayed to put the projectorinto standby mode.

• Unplug the power cord from the AC outlet after the cooling fan stops.

On-screen DisplayOn the

projectorOn the remote

control

_P. 29

XG-MB67X_EN2_CD_e 06.5.12, 6:42 AM17

18

Ceiling-mount Setup

It is recommended that you use the optionalSharp ceiling-mount bracket for this installa-tion. Before mounting the projector, contactyour nearest Sharp Authorized ProjectorDealer or Service Center to obtain the rec-ommended ceiling-mount bracket (sold sepa-rately).• AN-XRCM30 ceiling-mount bracket (for

U.S.A.).• AN-60KT ceiling-mount bracket, its AN-

TK201 and AN-TK202 extension tubes (forcountries other than the U.S.A.).

Invert the image by setting “Ceiling + Front”in “PRJ Mode”. See page 45 for use of thisfunction.

Setting up the Projector

Setting up the ProjectorFor optimal image quality, position the projector perpendicular to the screen with the projector’s feetflat and level. Doing so will eliminate the need for Keystone correction and provide the best imagequality. (See page 33.)

Side View

Standard Setup (Front Projection) Place the projector at the required distance from the screen according

to the desired picture size. (See page 20.)

Example of standard setup

Screen

Lens centerH

L

• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.

Note

XG-MB67X_EN2_CD_f 06.5.12, 6:43 AM18

19

Setu

p

300"

200"

100"84"60"

240"´180"

160"´120"80"´60"67"´50"48"´36"

34'3"–39'8"

(10.4 m – 12.1 m)22'10"–26'5"

(7.0 m – 8.1 m)11'5"–13'3"

(3.5 m – 4.0 m)9'7"–11'1"

(2.9 m – 3.4 m)6'10"–7'11"

(2.1 m – 2.4 m)

Projection (PRJ) ModeThe projector can use any of the 4 projection modes shown in the diagram below. Select the modemost appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu.See page 45.)

Table mounted, front projection Ceiling mounted, front projection

Menu item “Front”

Table mounted, rear projection(with a translucent screen)

Menu item “Ceiling + Front”

Ceiling mounted, rear projection(with a translucent screen)

Menu item “Rear” Menu item “Ceiling + Rear”

Indication of the Projection Image Size and Projection Distance

Picture Size

ProjectionDistance

Example: NORMAL Mode (4:3)

XG-MB67X_EN2_CD_f 06.5.12, 6:43 AM19

20

Setting up the Projector (Continued)

300 (762 cm)

270 (686 cm)

250 (635 cm)

200 (508 cm)

150 (381 cm)

100 (254 cm)

84 (213 cm)

80 (203 cm)

72 (183 cm)

60 (152 cm)

40 (102 cm)

610 cm (240)

549 cm (216)

508 cm (200)

406 cm (160)

305 cm (120)

203 cm (80)

171 cm (67)

163 cm (64)

146 cm (58)

122 cm (48)

81 cm (32)

48 cm

44 cm

40 cm

32 cm

24 cm

16 cm

14 cm

13 cm

12 cm

10 cm

6 cm

(19 5/64)

(17 11/64)

(15 57/64)

(12 23/32)

(9 17/32)

(6 23/64)

(5 11/32)

(5 3/32)

(4 37/64)

(3 13/16)

(2 35/64)

457 cm (180)

411 cm (162)

381 cm (150)

305 cm (120)

229 cm (90)

152 cm (60)

128 cm (50)

122 cm (48)

110 cm (43)

91 cm (36)

61 cm (24)

10.4 m (34 3)

9.4 m (30 10)

8.7 m (28 7)

7.0 m (22 10)

5.2 m (17 2)

3.5 m (11 5)

2.9 m (9 7)

2.8 m (9 2)

2.5 m (8 3)

2.1 m (6 10)

1.4 m (4 7)

12.1 m (39 8)

10.9 m (35 8)

10.1 m (33 1)

8.1 m (26 5)

6.0 m (19 10)

4.0 m (13 3)

3.4 m (11 1)

3.2 m (10 7)

2.9 m (9 6)

2.4 m (7 11)

1.6 m (5 3)

The formula for picture size and projection distance[m/cm]L1 (m) = 0.03794χL2 (m) = 0.04389χH (cm) = 0.3835χS (cm) = ±0.20754χ

Screen Size and Projection Distance

• Refer to page 18 concerning “Projection distance (L)” and “Distance from the lens center to thebottom of the image (H)”.

• Allow a margin of error in the values in the diagrams above.

NORMAL Mode (4:3)Picture (Screen) size

The formula for picture size and projection distance[m/cm]L1 (m) = 0.03482χL2 (m) = 0.04029χH (cm) = 0.16151χ

χ: Picture size (diag.) (in/cm)L: Projection distance (m/ft)L1: Minimum projection distance (m/ft)L2: Maximum projection distance (m/ft)H: Distance from the lens center to the bottom of the image (cm/in)

χ: Picture size (diag.) (in/cm)L: Projection distance (m/ft)L1: Minimum projection distance (m/ft)L2: Maximum projection distance (m/ft)H: Distance from the lens center to the bottom of the image (cm/in)S: Adjustable range of image position (cm/in) See page 44.

Projection distance [L]Diag. [χ] Width Height Minimum [L1] Maximum [L2]

STRETCH Mode (16:9)

250 (635 cm)

225 (572 cm)

200 (508 cm)

150 (381 cm)

133 (338 cm)

106 (269 cm)

100 (254 cm)

92 (234 cm)

84 (213 cm)

80 (203 cm)

72 (183 cm)

60 (152 cm)

40 (102 cm)

553 cm (218)

498 cm (196)

443 cm (174)

332 cm (131)

294 cm (116)

235 cm (92)

221 cm (87)

204 cm (80)

186 cm (73)

177 cm (70)

159 cm (63)

133 cm (52)

89 cm (35)

96 cm

86 cm

77 cm

58 cm

51 cm

41 cm

38 cm

35 cm

32 cm

31 cm

28 cm

23 cm

15 cm

(37 3/4)

(33 31/32)

(30 13/64)

(22 41/64)

(20 5/64)

(16)

(15 3/32)

(13 57/64)

(12 11/16)

(12 5/64)

(10 7/8)

(9 1/16)

(6 3/64)

52 cm

47 cm

42 cm

31 cm

28 cm

22 cm

21 cm

19 cm

17 cm

17 cm

15 cm

12 cm

8 cm

(20 27/64)

(18 25/64)

(16 11/32)

(12 1/4)

(10 7/8)

(8 21/32)

(8 11/64)

(7 33/64)

(6 55/64)

(6 17/32)

(5 57/64)

(4 29/32)

(3 17/64)

311 cm (123)

280 cm (110)

249 cm (98)

187 cm (74)

166 cm (65)

132 cm (52)

125 cm (49)

115 cm (45)

105 cm (41)

100 cm (39)

90 cm (35)

75 cm (29)

50 cm (20)

9.5 m (31 1)

8.5 m (28 0)

7.6 m (24 11)

5.7 m (18 8)

5.0 m (16 7)

4.0 m (13 2)

3.8 m (12 5)

3.5 m (11 5)

3.2 m (10 5)

3.0 m (9 11)

2.7 m (9 0)

2.3 m (7 6)

1.5 m (5 0)

11.0 m (36 0)

9.9 m (32 5)

8.8 m (28 10)

6.6 m (21 7)

5.8 m (19 2)

4.7 m (15 3)

4.4 m (14 5)

4.0 m (13 3)

3.7 m (12 1)

3.5 m (11 6)

3.2 m (10 4)

2.6 m (8 8)

1.8 m (5 9)

Note

Distance from the lens centerto the bottom of the image [H]

Picture (Screen) size Projection distance [L]Diag. [χ] Width Height Minimum [L1] Maximum [L2]

Distance from the lens center tothe bottom of the image [H]

Adjustable range ofimage position [S]

[Feet/inches]L1 (ft) = 0.03482χ / 0.3048L2 (ft) = 0.04029χ / 0.3048H (in) = 0.16151χ / 2.54

[Feet/inches]L1 (ft) = 0.03794χ / 0.3048L2 (ft) = 0.04389χ / 0.3048H (in) = 0.3835χ / 2.54S (in) = ±0.20754χ / 2.54

XG-MB67X_EN2_CD_f 06.5.12, 6:43 AM20

21

Co

nn

ection

s

Connections

INPUT Terminals and Connectable Main Equipment

INPUT 1, 2 terminal Connecting the computer. (See page 23.) Connecting video equipment with compo-

nent output terminal (DVD player, DTVdecoder, DVD recorder with hard disc,etc.). (See page 24.)

INPUT 3 terminalConnecting video equipment withS-video output terminal (VCR, DVDplayer, etc.). (See page 24.)

INPUT 4 terminalConnecting video equipment without S-video output terminal. (See page 25.)

AUDIO (INPUT 1, 2) terminalConnecting an audio cable(Shared audio input terminal forINPUT 1 and 2). (See pages 23and 24.)

AUDIO (INPUT 3, 4) terminalConnecting an audio cable(Shared audio input terminalfor INPUT 3 and 4). (Seepages 24 and 25.)

COMPUTER-RGB/COMPONENTOUTPUT terminalConnecting the monitor when you wantto simultaneously watch the projectionimage on the monitor. (See page 25.)

RS-232C terminalConnecting the computer tocontrol the projector. (Seepage 26.)

AUDIO OUTPUT terminalConnecting to an amplifier or otheraudio equipment with an audio cable(commercially available) (Sharedaudio output terminal for INPUT 1, 2,3 and 4).Use an audio cable with ø3.5 mmminijack plug to connect to thisterminal.

Rear View

LAN terminal(10 BASE-T/100 BASE-TX)Connecting the computer or the hubusing a LAN cable. (See page 27.)

XG-MB67X_EN2_CD_g 06.5.12, 6:44 AM21

22

Samples of Cables for Connection

Cables for a cameraor a video game

Equipment InputSignal Cable Terminal on the

projector

ø3.5 mm stereo audio cable(commercially available or available as Sharpservice part QCNWGA038WJPZ)

RGB cable (supplied)

S-video cable (commercially available)

Video cable (commercially available)

Computer

Audio-visualequipment

Camera/video game

RGBvideo

Computeraudio

S-video

S-video

Compo-nentvideo

Video

Audio

Cables for a camera or a video game/3 RCA(Component) to 15-pin D-sub cable (optional,AN-C3CP2)

ø3.5 mm minijack to RCA audio cable(commercially available)

INPUT1, 2

AUDIO INPUT

INPUT3

INPUT4

AUDIO INPUT

INPUT1, 2

INPUT3

Video

Audio

Cables for a cameraor a video game

Cables for a camera or a video game/ø3.5mm minijack to RCA audio cable (commer-cially available)

INPUT4

AUDIO INPUT

3 RCA (Component) to 15-pin D-sub cable(optional, AN-C3CP2)Compo-

nentvideo

INPUT1, 2

• For more details of connection and cables, refer to the operation manual of the connecting equipment.• You may need other cables or connectors not listed below.

RCA adaptor plug(commercially available)

RCA adaptor plug(commercially available)

or

or connect directly toAUDIO (INPUT 3, 4).

or

or

XG-MB67X_EN2_CD_g 06.5.12, 6:44 AM22

23

Co

nn

ection

s

Connecting to a Computer

To RGB output terminal

To audio output terminal

RGB Cable

* ø3.5 mm stereo ormono audio cable(commerciallyavailable oravailable as Sharpservice partQCNWGA038WJPZ)

RGB Cable

Before connecting, ensure that the power cord of the projector is unplugged from the ACoutlet and turn off the devices to be connected. After making all connections, turn on theprojector and then the other devices. When connecting a computer, ensure that it is the lastdevice to be turned on after all the connections are made.Ensure that you have read the operation manuals of the devices to be connected before makingconnections.

* When using the ø3.5 mm mono audio cable, the volume level will be half ofwhen using the ø3.5 mm stereo audio cable.

• See page 58 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-tor. Use with computer signals other than those listed may cause some of the functions to not work.

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-est Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless thecomputer’s external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneouslywhen using a SHARP notebook computer). Refer to the specific instructions in your computer'soperation manual to enable your computer’s external output port.

Note

To INPUT1 terminal To AUDIO(INPUT1, 2)

terminal

Suppliedaccessory

Computer

XG-MB67X_EN2_CD_g 06.5.12, 6:44 AM23

24

L

R

Connecting to Video Equipment

The projector is equipped with input terminals that support component, S-video, and video signals.See the illustration below to connect with the audio-visual equipment.The image quality is highest in the order of the component signal, the S-video signal and the videosignal. If your audio-visual equipment has a component output terminal, use the COMPUTER/COMPONENT terminal (INPUT1 or INPUT 2) on the projector for video connection.

When using an S-video cable (INPUT3)

To S-video output terminal


S-video cable(commercially available)RCA audio cable (com-

mercially available)

When using a 3 RCA (Component) to 15-pin D-sub cable (INPUT1 or INPUT2)

3 RCA (Component)to 15-pin D-sub cable(optional: AN-C3CP2)

To AUDIO(INPUT1, 2)

terminal


ø3.5 mm minijack to RCAaudio cable (commerciallyavailable)

To component output (Y, CB/PB, CR/PR) terminalTo INPUT1terminal

To AUDIO(INPUT3, 4)

terminalTo INPUT3terminal

DVD, etc.

DVD, etc.

XG-MB67X_EN2_CD_g 06.5.12, 6:44 AM24

25

Co

nn

ection

s

L

R

To video output terminal

When using a composite video cable(INPUT4)To audio output terminal

Note

Composite video cable(commercially available)RCA audio cable (com-

mercially available)

To AUDIO (INPUT3, 4) terminal

To INPUT4terminal

Connecting to a Monitor with RGB Input Terminal

You can display computer images on both the projector and a separate monitor using two sets ofRGB cables.

To RGBinputterminal

To RGB outputterminal

To INPUT 1terminal

To OUTPUT(INPUT 1, 2)

terminal

RGB cable (commercially available)RGB cable

• RGB signals and Component signals can be output to the monitor.• For this connection, another RGB cable (commercially available) is required.

DVD, etc.

Computer Monitor

XG-MB67X_EN2_CD_g 06.5.12, 6:44 AM25

26

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-232C adaptor and an RS-232C serial control cable (cross type, commercially available), the com-puter can be used to control the projector and check the status of the projector. Refer to the “SETUPMANUAL” contained on the supplied CD-ROM for details.

When connecting to a computer using an RS-232C serial control cable and a DIN-D-sub RS-232C adaptor

To RS-232C terminal

To RS-232C terminal

DIN-D-sub RS-232Cadaptor

RS-232C serial control cable (cross type, commercially available)

Note• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the

operation manual of the computer for details.• Refer to page 3 of the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Speci-

fications and Commands”.

Info• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This

may damage your computer or projector.• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.

This may damage your computer.

Computer

DIN-D-subRS-232Cadaptor

Suppliedaccessory

XG-MB67X_EN2_CD_g 06.5.12, 6:44 AM26

27

Co

nn

ection

s

Connecting the Power Cord

Plug the supplied power cord into theAC socket on the rear of the projector.Then plug into AC outlet.

AC socket

Power cordSuppliedaccessory

When connecting to the LAN terminal using a LAN cable

TX/RX LED (yellow)Illuminates when transmit-ting/receiving data.

LINK LED (green)Illuminates when linked.

Hubor

Computer

LAN cable (Category 5 type,commercially available) To LAN terminal

* To ensure safety, do notconnect the LAN terminalwith any cables that maycause excessive voltagesuch as a telephone line.

Note• When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially

available).• When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially

available).

To AC outlet

XG-MB67X_EN2_CD_g 06.5.24, 1:53 PM27

28

Turning the Projector On/Off

Remove the lens cap and pressSSTANDBY/ON on the projector orfON on the remote control.• When System Lock is set, the keycode input box

appears. To cancel the keycode setting, input thekeycode that you have already set. See page 47for details.

• About the Lamp IndicatorThe lamp indicator illuminates to indicate thestatus of the lamp.

Green: The lamp is on.Blinking in green:The lamp is warming up

or shutting down.Red:The lamp is shut down abnormally

or the lamp should be replaced.• When switching on the projector, a slight flick-

ering of the image may be experienced withinthe first minute after the lamp has been illumi-nated. This is normal operation as the lamp’scontrol circuitry is stabilising the lamp outputcharacteristics. It should not be regarded asfaulty operation.

• If the projector is put into standby mode andimmediately turned on again, the lamp maytake some time to start projection.

STANDBY/ON button

Note

Lamp indicator

• English is the factory default language. If youwant to change the on-screen display to an-other language, change the language accord-ing to the procedure on page 45.

Info

Turning the Projector on

Note that the connections to external equip-ment and power outlet should be done be-fore performing the operations written be-low. (See pages 23 to 27.)

ON button

XG-MB67X_EN2_CD_h 06.5.12, 6:45 AM28

29

Basic

Op

eration

On-screen Display (confirmation message)

Turning the Power off (Put-ting the Projector intoStandby Mode)

• Do not unplug the power cord during projec-tion or cooling fan operation. This can causedamage due to rise in internal temperature,as the cooling fan also stops.

Info

R

STANDBYbutton

Power indicator

STANDBY/ON button

1

2

Press SSTANDBY/ON on the pro-jector or eSTANDBY on the re-mote control, then press that but-ton again while the confirmationmessage is displayed, to put theprojector into standby mode.

Unplug the power cord from the ACoutlet after the cooling fan stops.• The power indicator on the projector

blinks in green while cooling.• The power indicator changes to red when

the projector finishes cooling.

XG-MB67X_EN2_CD_h 06.5.12, 6:45 AM29

30

About the Setup Guide

After turning on the projector, the SetupGuide screen appears to assist you withprojector setup.

Press TENTER to exit the Setup Guidescreen.

Guidance items1 FOCUS2 HEIGHT ADJUST3 ZOOM

STANDBY/ONbutton

ENTER button

1 Adjusting the FocusYou can adjust the focus with the focusring on the projector.

Image Projection

Rotate the focus ring to adjust the fo-cus while watching the projected image.

Setup Guide screen

• The Setup Guide screen automatically high-lights the items in the following order:

1 FOCUS

3 ZOOM4 ENTER

2 HEIGHT ADJUST

However, you can adjust the focus, height(angle), or zoom regardless of the highlighteditem.

• If you do not want to display the Setup Guidefor the next time, set “Menu” - “SCR - ADJ” -“Setup Guide” to “Off”. (See page 45.)

Note

Focus ring

Adjusting the Projected Image

2 Adjusting the Screen SizeYou can adjust the screen size usingthe zoom ring on the projector.

Rotate the zoom ring to enlarge orshrink the screen size.

Zoom ring

XG-MB67X_EN2_CD_h 06.5.12, 6:46 AM30

31

Basic

Op

eration

3 Adjusting the Height

The height of the projector can be ad-justed using the adjustment feet at thefront and rear of the projector.When the screen is above the projec-tor, the projection image can be madehigher by adjusting the projector.

1

2

3

• Do not apply too much pressure on the pro-jector when the front adjustment foot comesout.

• When lowering the projector, be careful not toget your fingers caught in the area betweenthe adjustment foot and the projector.

• Hold the projector firmly while lifting or carry-ing.

• Do not hold by the lens area.

Use the rear adjustment foot tomake the projector level.• The projector is adjustable ±1 degree

from the standard position.

Remove your hands from theHEIGHT ADJUST lever of the pro-jector after its height has beenfinely adjusted.• The angle of projection is adjustable up

to 8 degrees from the surface on whichthe projector is placed.

Lift the projector to adjust itsheight while lifting the HEIGHTADJUST lever.

HEIGHTADJUST lever

Info

Rear adjustment foot

• When adjusting the height of the projector,trapezoidal distortion occurs. Follow the pro-cedures in Keystone Correction to correct thedistortion. (See pages 33 and 44.)

Note

Make smalladjustments.

XG-MB67X_EN2_CD_h 06.5.12, 6:46 AM31

32

Image Projection (Continued)

Displaying the Black Screenand Turning off the SoundTemporarily

Adjusting the Volume

Switching the Input Mode

PressC INPUT 1, C INPUT 2,DINPUT 3 or EINPUT 4 on the remotecontrol to select the input mode.• When pressing INPUT (P/R) on the projector,

input mode switches in the following order:INPUT1 INPUT2 INPUT3 INPUT4 .

• When “Auto Search” is set to “On”, INPUT (P/R) on the projector functions as the Auto Searchbuttons. (See page 46.)

Select the appropriate input mode forthe connected equipment.

Press K/L on the remote control or–O/Q+ on the projector to adjust the vol-ume.

• Pressing K/–O will lower the volume.• Pressing L/Q+ will raise the volume.• When the projector is connected to external

equipment, the volume level of the external equip-ment changes in accordance with the volumelevel of the projector. Set the projector’s volumeto the lowest level when turning the projector on/off or when changing the input signal.

• When you do not want to output the sound fromthe projector’s speaker while the projector is con-nected to external equipment, set “Speaker” in“PRJ-ADJ” menu to “Off”. (See page 46.)

Press MAV MUTE on the remote con-trol to temporarily display a blackscreen and turn off the sound.

• Pressing MAV MUTE again will turn the projectedimage back on.

Volume buttons

INPUTbuttons

AV MUTE button

On-screen Display

Note

Note On-screen Display

XG-MB67X_EN2_CD_h 06.5.12, 6:46 AM32

33

Basic

Op

eration

0KeystoneADJ. END

Correcting TrapezoidalDistortion

When the image is projected either fromthe top or from the bottom towards thescreen at an angle, the image becomesdistorted trapezoidally. The function forcorrecting trapezoidal distortion iscalled Keystone Correction.

• The Keystone Correction can be adjusted upto an angle of approximately ±13 degrees andthe screen can also be set up to an angle ofapproximately ±13 degrees (when the resizemode is set to “NORMAL” (see page 34)).

Note

1

2

3 Press g KEYSTONE.• The on-screen display of the Keystone

Correction mode will disappear.• You can also use d KEYSTONE on the

projector.

Press P/Q or O/R to adjust theKeystone Correction.• You can also adjust the Keystone Cor-

rection using the adjustment buttons onthe projector.

Press g KEYSTONE to enter theKeystone Correction mode.• You can also display the on-screen dis-

play of the Keystone Correction modewith d KEYSTONE on the projector.

• Press l RETURN while the on-screen dis-play of the Keystone Correction mode is onthe screen to return to the default setting.

Note

KEYSTONE button


RETURN button

ROn-screen display(Keystone Correction mode)

Shrinks upper side.(Move the slide bar in the + direction.)

Shrinks lower side.(Move the slide bar in the - direction.)

• While adjusting the image using KeystoneCorrection, straight lines and the edges of theimage may appear jagged.

Info

About the Auto Keystone Correction

• The projector automatically detects tilt and theAUTO KEYSTONE feature automatically cor-rects trapezoidal distortion.

• Automatic Keystone Correction may not work well in somecases, such as when the screen is leaning, temperature isextremely high or low, or zoom is at maximum or mini-mum. In these cases, fine adjust the Keystone Correctionfollowing steps 1 to 3.

• You can select “On” or “Off” for the Auto Keystone Correc-tion mode. (See page 44.)

Note

XG-MB67X_EN2_CD_h 06.5.12, 6:46 AM33

34

Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. De-pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.

Press HRESIZE.• See page 44 for setting on menu screen.

Computer

Input Signal

NORMAL

Output screen image

Computer Image type BORDER STRETCH

SXGA(1280K1024)

1280K720

4:3 aspect ratio

5:4 aspect ratio

16:9 aspectratio

* Mode for projecting an image with the originalaspect ratio without cutting any portions.

RESIZE button

SVGA (800 K 600)

XGA (1024 K 768)

SXGA (1280 K 960)

SXGA L (1400 K 1050)

SXGA (1280 K 1024)

1280 K 720

1024 K 768

J

768 K 576

J

1024 K 576

1024 K 576

1024 K 768 768 K 576 1024 K 576

NORMAL BORDER STRETCH

Other aspect ratios

4:3 aspect ratio

: Cutout area on which images cannot be projected.

Resolution lower than XGA

XGA

Resolution higher than XGA

XG-MB67X_EN2_CD_h 06.5.12, 6:46 AM34

35

Basic

Op

eration

VIDEO

• “STRETCH” is fixed when 540P, 720P or 1080I signals are entered.

: Cutout area on which images cannot be projected.: Area on which the image is not included in the original signals.

Input Signal

DVD / Video Image type

Output screen image

NORMAL BORDER STRETCH

480I, 480P, 576I,576P, NTSC, PAL,

SECAM

540P, 720P, 1080I

4:3 aspect ratio

Letter box

Squeezed 16:9 image

Squeezed 4:3 image

16:9 aspect ratio

16:9 aspect ratio(4:3 aspect ratio in

16:9 screen)

* Mode for projecting an image with the original aspect ratio without cutting any portions.

XG-MB67X_EN2_CD_h 06.5.12, 6:46 AM35

36

Auto Sync(Auto Sync Adjustment)

Operating with the Remote Control

Freezing a Moving Image

• When the optimum image cannot be achievedwith Auto Sync adjustment, use the help menufor manual adjustments. (See page 51.)

Auto Sync function works when detect-ing input signal after the projector turnson.Press FAUTO SYNC to manually ad-just with Auto Sync function.

Press NFREEZE.• The projected image is frozen.

Press NFREEZE again to returnto the moving image from the cur-rently connected device.

1

2

Note

Selecting the Picture Mode

Press GPICTURE MODE.• When pressing GPICTURE MODE, the picture

mode changes in the following order:Standard Presentation Movie Game sRGB

You can select the appropriate picturemode for the projected image, such asmovie or video game.

• See page 42 for details on the picture mode.

Note

FREEZE button

AUTO SYNCbutton


BREAK TIMERbutton

PICTURE MODEbutton

Displaying and Setting theBreak Timer

Press k BREAK TIMER.• The timer starts to count down from 5

minutes.

1

2Press P /R /O /Q to adjust thelength of the break time.• Increases with P or Q

5 minutes s 6 minutes s 60 minutes• Shortens with O or R

4 minutes s 3 minutes s1 minute• The break time can be set in units of one

minute (up to 60 minutes).

ROn-screen display

Canceling the break time display function

Press k BREAK TIMER.*

* “sRGB” is displayed only when RGB signal isinput.

• Break Timer does not function while the pro-jector is operating the “Auto Sync”, “FREEZE”or “AV MUTE” functions.

Note

XG-MB67X_EN2_CD_i 06.5.12, 6:47 AM36

37

Usefu

lF

eatures

The following shows the items that can be set in the projector.

Menu Items

“Screen adjustment (SCR-ADJ)” menu

INPUT 1 (Component)/INPUT 2(Component)/INPUT 3/INPUT 4

INPUT 1 (RGB)/INPUT2 (RGB)

“Picture” menu

Picture SCR PRJ Net.


000K8 5 0 0

BrightRedBlue


Standard

BrightReset

SEL./ADJ. ENTER END

Help


000

K8 5 0 0

BrightColorTint

0Sharp

1CLR TempBright BoostProgressive 3D Progressive

Standard

ResetSEL./ADJ. ENTER END


Lamp Setting Bright

ResizeImage Shift 0

0KeystoneAuto KeystoneOSD DisplayBackgroundSetup GuidePRJ ModeLanguage

FrontEnglish

OnLogoOnOff

Normal

SEL./ADJ. ENTER END

Pict. SCR - ADJ PRJ Net. Help

Main menu Sub menu

Picture

Page 42

+30-30Contrast

+30-30

+30-30

+30-30

+30-30

+30-30

+30-30

Tint

Color

Sharp

Bright

Red

Blue

*2*3

*2

*2

*1

*1

Progressive

Lamp Setting

*2

Reset

5500K6500K7500K8500K9300K10500K

2D Progressive3D ProgressiveFilm Mode

BrightEco + Quiet

CLR Temp

Bright Boost [0/1/2]

Page 42

Page 43

Page 43

Page 43

Page 43

Page 43

StandardPresentationMovieGamesRGB*1

Picture Mode

Main menu Sub menu

SCR - ADJ

Page 44

Language

Image Shift

Resize

Page 44

Page 44

Page 44

Page 44

Page 45

Page 45

Page 45

Page 45

Page 45

Keystone

Auto Keystone [On/Off]

OSD Display [On/Off]

Background

Setup Guide [On/Off]

PRJ Mode

NormalBorderStretch

LogoBlueNone

FrontCeiling + FrontRearCeiling + Rear

EnglishDeutschEspañolNederlandsFrançaisItalianoSvenskaPortuguês

+127-127

+96-96

*1 Items when inputting RGB signal through INPUT 1 orINPUT 2.

*2 Items when inputting component signal through INPUT 1 orINPUT 2, or when selecting INPUT 3 or INPUT 4.

*3 “Tone” will appear on the menu screen only when PAL orSECAM signals are input (including when forcibly changedto those input signals). There is basically no need to adjust“Tone”, but you can adjust the picture tone with thisadjustment when inputting PAL or SECAM signals.

• You can adjust the menu items with icons ( , ,and ) using the respective buttons on the re-mote control.

XG-MB67X_EN2_CD_i 06.5.12, 6:47 AM37

38

“Projector adjustment (PRJ-ADJ)” menu

Pict.

Auto Search

SCR PRJ - ADJ Net.

Auto SyncAuto Power OffSystem Sound

System Lock

h

OnOnOnOn

SEL./ADJ. ENTER END

0Lamp Timer(Life) 100%

Help

Speaker OnRS-232C 9600 bpsFan Mode Normal

Disable

Main menu Sub menu

PRJ - ADJ

Page 46Auto Search [On/Off]

Auto Sync [On/Off]

Auto Power Off [On/Off]

System Sound [On/Off]

Speaker [On/Off]

System Lock

Lamp Timer(Life)

Page 46

Page 46

Page 46

Page 46

Page 46

Page 47

Page 47

Old CodeNew CodeReconfirm

Fan Mode

Page 47NormalHigh

RS-232C

Page 479600 bps115200 bps

Menu Items (Continued)

“Network” menu

Pict.

Password

SCR PRJ Network

DHCP Client

SEL./ADJ. ENTER END

Projector

MAC Address

XG-MB67X

0 8 : 0 0 : 1 F : B 1 : B 7 : 7 4

Help

Disable

On

TCP/IP

Main menu Sub menu

Network

Page 49Password [Enable/Disable]

DHCP Client [On/Off]

TCP/IP

MAC Address

Projector

Page 49

Page 50

Page 50

Page 50

Page 50

XG-MB67X_EN2_CD_i 06.5.12, 6:47 AM38

39

Usefu

lF

eatures

Pict.

There is no picture or audio

SCR Net.PRJ Help

Vertical stripes or flickering image appearData image is not centeredColor is faded or poorPicture is darkThe image is distorted

Reset all adjustments to default settings

SEL. ENTER END

“Help” menu The items you can set with the “Help”menu

“Help” menu n Page 51• Vertical stripes or flickering image appear

Auto SyncAdjust vertical noiseAdjust horizontal noise

• Data image is not centeredAuto SyncH-PosV-Pos

• Color is faded or poorINPUT 1 or INPUT 2

Signal type: Auto/RGB/ComponentINPUT 3 or INPUT 4

Video System: A u t o / P A L / S E C A M /NTSC3.58/NTSC4.43/PAL-M/PAL-N/PAL-60

* The selectable items vary depending on the in-put signal and the selected input mode.

XG-MB67X_EN2_CD_i 06.5.12, 6:47 AM39

40

Using the Menu Screen

Menu Selections (Adjustments)

Example: Adjusting “Bright”.• This operation can also be performed by using the buttons on the projector.

Press BMENU.• The “Picture” menu screen for the se-

lected input mode is displayed.


Example: “Picture” screen menu for INPUT 1(RGB) mode

Press Q or O and select “Picture”to adjust.

1

2

ENTER button

RETURN button

Menu item


000K8 5 0 0

BrightRedBlue


Standard

BrightReset

SEL./ADJ. ENTER END


MENU/HELPbutton

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

• Press lRETURN toreturn to the previousscreen when the menuis displayed.

XG-MB67X_EN2_CD_i 06.5.12, 6:47 AM40

41

Usefu

lF

eatures

Press P or R and select “Bright”to adjust.• The selected item is highlighted.

• Press hENTER again to return to theprevious screen.

Press O or Q to adjust the itemselected.• The adjustment is stored.

Press BMENU/HELP.• The menu screen will disappear.

3

4

5

0Bright

Picture

SEL./ADJ. Rtn. Menu END


1 500K8 5 0 0

BrightRedBlue


Standard

BrightReset

SEL./ADJ. Single ADJ END


Note


000K8 5 0 0

BrightRedBlueCLR TempBright BoostLamp Setting

Standard

BrightReset

SEL./ADJ. Single ADJ END

ResizeImage Shift 0

0KeystoneAuto Keystone Off

Normal

1


Pict. SCR - ADJ PRJ Net. Help

Items to be adjusted

• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Time”,“FREEZE”, or “AV MUTE” functions.

Note

To adjust the projectedimage while watching itPress hENTER.• The selected item (e.g. “Bright”) is dis-

played by itself at the bottom of thescreen.

• When pressing P or R, the following item(“Red” after “Bright”) will be displayed.

The item displayed by itself

XG-MB67X_EN2_CD_i 06.5.12, 6:47 AM41

42

Picture Adjustment (“Picture” menu)

Selectableitems

Standard

Presentation

Movie

Game

*sRGB

Q Example: “Picture” screen menu forINPUT 1 (RGB) mode

Q Example: “Picture” screen menu forINPUT 3 mode


000K8 5 0 0

BrightRedBlue


Standard

BrightReset

SEL./ADJ. ENTER END


Description

For standard image

Brightens portions of image formore enhanced presentations.

Gives natural tint to theprojected image.

Gives sharpness to theprojected image.

For high fidelity reproduction ofimages from a computer.


000

K8 5 0 0

BrightColorTint

0Sharp

1CLR TempBright BoostProgressive 3D Progressive

Standard

ResetSEL./ADJ. ENTER END


Lamp Setting Bright

Menu operation n Page 40

• You can also press G PICTURE MODE on the remote control to select the picture mode. (Seepage 36.)

• *sRGB is an international standard of color reproduction regulated by the IEC (InternationalElectrotechnical Commission). As the fixed color area has been decided by the IEC, the images aredisplayed in a natural tint based on an original image, when “sRGB” is selected.For additional information about the sRGB function, visit “http://www.srgb.com/”.You cannot set the items, “Red”, “Blue”, “CLR Temp”, “Bright Boost”, when “sRGB” is selected.

Note

1 1 1 1 1 Selecting the Picture Mode

• When “sRGB” is selected, the projected image may become dark, but this does not indicate amalfunction.

Info

• “sRGB” is displayed only when RGB signal is input.• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are

retained in memory.

CLR Temp

8500K

8500K

6500K

8500K

–

Lamp Setting

Bright

Bright

Eco + Quiet

Bright

Bright

The default settings of each item when selecting Picture Mode

Bright Boost

1

2

0

2

–

XG-MB67X_EN2_CD_j 06.5.12, 6:48 AM42

43

Usefu

lF

eatures

44444 Progressive

• In NTSC or PAL60Hz, even if the 3D Progres-sive mode has been set, the three-two pulldown enhancement will be enabled automati-cally when the film source has been entered.

• When the image is blurred or noisy, switch tothe optimal mode.

• When using progressive inputs, inputs are di-rectly displayed so that 2D Progressive, 3DProgressive and Film Mode cannot be se-lected.

* The film source is a digital video recording with theoriginal encoded as is at 24 frames/second. Theprojector can convert this film source to progres-sive video at 60 frames/second with NTSC andPAL60Hz or at 50 frames/second with PAL50Hzand SECAM to play back a high-definition image.

Selectableitems

2DProgressive

3DProgressive

Film Mode

Description

Useful to display fast-moving imagessuch as sports.

Useful to display relatively slow-moving images such as drama anddocumentary more clearly.

Reproduces the image of film source*clearly. Displays the optimized image offilm transformed with three-two pull down(NTSC and PAL60Hz) or two-two pulldown (PAL50Hz and SECAM) enhance-ment to progressive mode images.

Note

55555 Lamp Setting

Select-ableitems

Eco +Quiet

Bright

Bright-ness

Approx.80%

100%

Powerconsumption(When using

AC 110V)

308W

385W

Lamp Life

Approx.3,000hours

Approx.2,000hours

Fansound

Low

Normal

• When “Lamp Setting” is set to “Eco+Quiet”,the power consumption will decrease and thelamp life will extend. (Projection brightnessdecreases approximately 20%.)

Note

22222 Adjusting the Image

*1 Not adjustable/selectable when selecting“sRGB”.

*2 Not displayed in the RGB input mode.*3 “Tone” will appear on the menu screen only when

PAL or SECAM signals are input (including whenforcibly changed to those input signals). There isbasically no need to adjust “Tone”, but you canadjust the picture tone with this adjustment wheninputting PAL or SECAM signals .

Q button

For morecontrast.

For morebrightness.

For stronger red.

For strongerblue.

For more colorintensity.

For making skintones greenish.

For moresharpness.

For morevividness.

AdjustmentItems

Contrast

Bright

Red*1

Blue*1

Color*2

Tint*2 *3

Sharp*2

Bright Boost*1

O button

For lesscontrast.

For lessbrightness.

For weaker red.

For weakerblue.

For less colorintensity.

For making skintones purplish.

For lesssharpness.

For high fidelitycolor reproduc-tion.

Note• “Bright Boost” and “CLR Temp” cannot be set

when “sRGB” is selected.• To reset all adjustment items, select “Reset”

and press hENTER.

33333 Adjusting the ColorTemperature

• Values on “CLR Temp” are only for generalstandard purposes.

Note

Selectableitems

5500K6500K7500K8500K9300K10500K

Description

For lower color temperature forwarmer, reddish incandescent-likeimages.

For higher color temperature forcooler, bluish, fluorescent-like images.


P

R

XG-MB67X_EN2_CD_j 06.5.12, 6:48 AM43

44

Adjusting the Projected Image(“SCR - ADJ” menu)

Pict.

ResizeImage Shift 0

0

SCR - ADJ PRJ Net.

KeystoneAuto KeystoneOSD DisplayBackgroundSetup GuidePRJ ModeLanguage

FrontEnglish

OnLogoOnOff

Normal

SEL./ADJ. ENTER END

Help

87654

3

21

11111 Setting the Resize Mode

• For details of the Resize mode, see pages 34and 35.

• You can also press HRESIZE on the remotecontrol to set the resize mode. (See page 34.)

Note

22222 Adjusting the ImagePosition

You can move the projected image vertically.

Q button

• You cannot set this item when “Resize” is setto “Normal”.

Note

O button


33333 Keystone Correction

When the image is projected either from the topor from the bottom towards the screen at anangle, the image becomes distortedtrapezoidally. The function for correcting trap-ezoidal distortion is called Keystone Correction.

For Manual Keystone Correction

Set “Auto Keystone” on the “SCR - ADJ”menu to “Off”, select “Keystone”, andthen adjust with the slide bar.

For Auto Keystone Correction

Set “Auto Keystone” on the “SCR - ADJ”menu to “On”.

O buttonQ buttonManual Correction

• The Keystone Correction can be adjusted upto an angle of approximately ±13 degrees withthe “Auto Keystone” and up to an angle ofapproximately ±13 degrees with the manual“Keystone” (when “Resize” is set to “Normal”).

Note

See page 33 for details of Keystone Correction.

XG-MB67X_EN2_CD_j 06.5.12, 6:48 AM44

45

Usefu

lF

eatures

The projector can switch the on-screen displaylanguage among 11 languages.

Selectable items

Front

Ceiling + Front

Rear

Ceiling + Rear

Description

Normal image (Projected fromthe front of the screen)

Inverted image (Projectedfrom the front of the screenwith an inverted projector)

Reversed image (Projectedfrom the rear of the screen orwith a mirror)

Reversed and inverted image(Projected with a mirror)

66666 Selecting the SetupGuide

88888 Selecting the On-screenDisplay Language

Selectable items

On

Off

Description

Displaying the Setup Guidewhen turning the projector on.

Not displaying the SetupGuide.

77777 Reversing/InvertingProjected Images

EnglishDeutschEspañolNederlandsFrançaisItalianoSvenskaPortuguês

44444 Setting the On-screenDisplay


Selectableitems

On

Off

Description

All On-screen Displays are displayed.

INPUT/VOLUME/AV MUTE/FREEZE/AUTO SYNC/RESIZE/PICTURE MODE/“An invalid button has been pressed.”are not displayed.

55555 Selecting the BackgroundImage

Selectable items

Logo

Blue

None

Description

Sharp logo screen

Blue screen

—

See page 19 for details of Projection (PRJ) Mode.

XG-MB67X_EN2_CD_j 06.5.12, 6:48 AM45

46

Adjusting the Projector Function (“PRJ - ADJ” menu)

Auto SearchAuto SyncAuto Power OffSystem Sound

System Lock

h

OnOnOnOn

SEL./ADJ. ENTER END

0Lamp Timer(Life) 100%

Pict. SCR PRJ - ADJ Net. Help

Speaker OnRS-232C 9600 bpsFan Mode Normal

Disable

11111 Auto Search FunctionThis function automatically searches for andswitches to the input mode in which signals arebeing received, when the projector is turned on,or when the INPUT button is pressed.

When “Auto Search” is set to “On”• If two or more input signals are found, the pro-

jector selects the input source in the order ofINPUT 1 n INPUT 2 n INPUT 3 n INPUT 4when you press INPUT (P/R) on the projector.

• While “Auto Search” is set to “On”, pressC INPUT 1,C INPUT 2, D INPUT 3 orEINPUT 4 on the remote control to selectan input mode other than the input mode se-lected by the projector.

Note

22222 Auto Sync (Auto SyncAdjustment)


• Auto Sync adjustment is also performed bypressing F AUTO SYNC on the remote con-trol.

• The Auto Sync adjustment may take some timeto complete, depending on the image of thecomputer connected to the projector.

• When the optimum image cannot be achievedwith Auto Sync adjustment, use manual ad-justments. (See page 51.)

Note

Selectable items

On

Off

Description

Auto Sync adjustment willoccur when the projector isturned on or when the inputsignals are switched, whenconnected to a computer.

Auto Sync adjustment is notautomatically performed.

• When the Auto Power Off function is set to“On”, 5 minutes before the projector entersstandby mode, the message “Enter STANDBYmode in X min.” will appear on the screen toindicate the remaining minutes.

Selectableitems

On

Off

Description

When no input signal is detected formore than 15 minutes, the projector willautomatically enter standby mode.

The Auto Power Off function will bedisabled.

Note

33333 Auto Power OffFunction

55555 Speaker Setting

Selectableitems

On

Off

Description

The audio signal is output from theinternal speaker.

The audio signal is not output from theinternal speaker.

44444 Setting the ConfirmationSound (System Sound)

Selectableitems

On

Off

Description

A confirmation sound is made whenthe projector turns on/off.

No confirmation sound is made.

XG-MB67X_EN2_CD_j 06.5.12, 6:48 AM46

47

Usefu

lF

eatures

Info

This function prevents unauthorized use of theprojector. Once this function is activated, usersmust enter the correct keycode each time theprojector is turned on. We suggest you recordthe keycode in a safe place where only au-thorized users have access.

• If you lose or forget your keycode, contact yournearest Sharp Authorized Projector Dealer orService Center (see page 61). Even if the prod-uct warranty is valid, the keycode reset willincur a charge.

Select “System Lock”, then presshENTER or Q.• The screen for entering the keycode

appears.

1

88888 System Lock Function

77777 Fan Mode Setting


This function changes the fan rotation speed.

Selectableitems

Normal

High

Description

Suitable for normal environments.

Select this when using the projector ataltitudes of approximately 1,500meters (4,900 feet) or more.

66666 Selecting the TransmissionSpeed (RS-232C)

Make sure that both the projector and computerare set for the same baud rate.

Selectableitems

9600bps

115200bps

Description

Transmission speed is slow.

Transmission speed is rapid.

P

R

99999 Checking the Lamp LifeStatus

You can confirm the cumulative lamp usage timeand the remaining lamp life (percentage).

• It is recommended that the lamp be changedwhen the remaining lamp life becomes 5%.

• The lamp life may vary depending on the us-age condition.

Lamp usage condition

Operated exclusivelywith Lamp Setting set to“Eco +Quiet”

Operated exclusivelywith Lamp Setting set to“Bright”

100%

Approx.3,000hours

Approx.2,000hours

5%

Approx.150 hours

Approx.100 hours

Remaining lamp life

Note

“Life”

a Setting/Changing the keycode

When “Fan Mode” is set to “High”, the fan rotationspeeds up, and the fan noise becomes louder.

Press the 4 buttons on the remotecontrol or on the projector to en-ter the preset keycode in “OldCode”.• When setting the keycode for the first

time, press R on the projector for fourtimes.

Setting the System Lock

PRJ - ADJ


– – – –– – – –– – – –

2

• If you input a wrong keycode, the cursorreturns to the first point of the “Old Code”.

• The preset keycode is 4 R buttons onthe projector. When you press the R but-ton four times, the keycord input screendisappears.

Note

XG-MB67X_EN2_CD_k 06.5.12, 6:49 AM47

48

Input screen for keycode

• You can not use the following buttons forkeycode:• S STANDBY/ON• f ON• e STANDBY• h ENTER• l RETURN• B MENU/HELP

• System lock function recognizes eachbutton on the remote control or on theprojector as an individual button, evenif they share the same button name. Ifyou used the buttons on the projectorin setting your keycode, the keycodecannot be canceled with the remotecontrol.

Press the 4 buttons on the remotecontrol or on the projector to en-ter the new keycode in “NewCode”.

3

Note


Locking the OperationButtons on the Projector(Keylock Function)Use this function to lock the operationbuttons on the projector.

a Taking the Keylock offHold down T ENTER on the projector forabout 5 seconds.

ROn-screen Display

a Locking the Operation ButtonsHold down T ENTER on the projector forabout 5 seconds while the projector is beingturned on.

ROn-screen Display

• The keylock function does not affect the op-eration with the remote control buttons.

• You cannot use the keylock function while theprojector is warming up.

• When the projector is in standby mode, youcan release the keylock by holding downT ENTER and S STANDBY/ON on the pro-jector simultaneously for about 5 seconds.

• Keylock does not function while the projectoris: displaying the “Setup Guide” or “Menu”screens, in standby mode, warming up,changing input signals, operating “Auto Sync”function, in “FREEZE” mode or on the “Sys-tem Lock” screen during warming up.

Info

Adjusting the Projector Function (“PRJ - ADJ” menu) (Continued)

NoteTo cancel the keycode that you have alreadyset

• Press R on the projector for four times in steps2 and 3 above.

When the System Lock is set• When System Lock is set, the keycode input

screen appears after the power is turned on.When it appears, enter the right keycode tostart projection.

Enter the same keycode in “Re-confirm”.

Setting the System Lock

PRJ - ADJ


* * * *– – – –– – – –

System Lock – – – –

4

XG-MB67X_EN2_CD_k 06.5.12, 6:50 AM48

49

Usefu

lF

eatures

Setting up the Projector Network Environment (“Network” menu)

If you do not want others to change the settingfor the “Network” menu, set a password.

Select “Password”, then presshENTER or Q.• The screen for entering the password

appears.

1

11111 Setting a Password

Press P or R to set the first digitin “New Password”, then press Q.

2

Enter the remaining 3 digits, thenpress hENTER.• To return to the previous digit, press O.

3

Enter the same password in “Re-confirm”, then press hENTER.• The status for “Password” changes to

“Enable”.

4

Note• Once after the password is set, you must en-

ter the password to change the “Network”menu settings.

Select “Password”, then presshENTER or Q.• The screen for entering the password

appears.

1

Enter the password in “Old Pass-word” using P, R, Q and O, thenpress hENTER.

Enter the password in “New Pass-word” using P, R, Q and O, thenpress hENTER.

Enter the same password again in“Reconfirm” using P, R, Q and O,then press hENTER.

Note• If you do not need the password protection

for the “Network” menu settings anymore,press hENTER without entering new pass-word in steps 3 and 4.

• To cancel the password settings, press lRETURN.

If you forget the passwordIf you forget the password, perform the fol-lowing procedure to delete it, then set a newpassword.

On the projector, pressS→T→S→T→S→T→U.

Note• If TENTER is held down for more than 5

seconds, the operation buttons on the pro-jector will be locked. (See page 48.)

• You cannot use the buttons on the remotecontrol to delete the password.

2

3

4

a Setting a Password

a Changing the Password

Pict.

Password

SCR PRJ Network

DHCP Client

SEL./ADJ. ENTER END

Projector

MAC Address

XG-MB67X

0 8 : 0 0 : 1 F : B 1 : B 7 : 7 4

Help

Disable

On

TCP/IP


Setting the Password

Old PasswordNew PasswordReconfirm

–– – ––– – –

– – – –

Network

XG-MB67X_EN2_CD_k 06.5.12, 6:50 AM49

50

33333 TCP/IP Setting

44444 Confirming theProjector Information

You can confirm the MAC address and projectorname.

Selectable items

IP Address

Subnet Mask

Gateway

Description

Factory default setting:192.168.150.002Enter an IP address appropri-ate for the network.

Factory default setting:255.255.255.000Set the subnet mask to thesame as that of the computerand equipment on thenetwork.

Factory default setting: 000.000. 000. 000* When not in use, set to “000.000. 000. 000”.

Displayed items

MAC Address

Projector

Description

The MAC address of theprojector is displayed.

The projector name isdisplayed. (Factory preset :XG-MB67X)

• Confirm the existing network’s segment (IPaddress group) to avoid setting an IP addressthat duplicates the IP addresses of other net-work equipment or computers. If“192.168.150.002” is not used in a networkwith an IP address of “192.168.150.XXX”, youdon’t have to change the projector IP address.

• For details about each setting, consult yournetwork administrator.

Note

Set the TCP/IP manually.

Select “Off” for “DHCP Client”,then press hENTER.

1

2 Select “TCP/IP”, then presshENTER.

Enter “IP Address” using P, R, Qand O, then press hENTER.

3

4 Enter “Subnet Mask” using P, R,Q and O, then press hENTER.

5 Enter “Gateway” using P, R, Q andO, then press hENTER.

Setting up the Projector Network Environment (“Network” menu)(Continued)

22222 DHCP Client Setting

Connect the LAN cable before turning the pro-jector on. If not, the DHCP Client function doesnot work.

Selectable items

On

Off

Description

Obtains configurationparameters for TCP/IP networkautomatically.

Sets the TCP/IP manually.

Select “On” for “DHCP Client”, then presshENTER. “Obtaining IP Address...” appears,then the menu screen appears. Confirm the pa-rameters of IP Address, Subnet Mask and Gate-way on the TCP/IP screen.

If the DHCP server is not available, “Could notobtain IP Address.” appears.

In this case, set the TCP/IP manually. (See theitem 3.)


• For information on how to change the projec-tor name, see “SETUP MANUAL” containedin the supplied CD-ROM.

Note

Setting the TCP/IP

Subnet MaskIP Address

Gateway

15 5 .29 2 .

0 0 0 .

15 5 .26 8 .

0 0 0 .

15 5 .25 0 .

0 0 0 .

00 000 2

0 0 0

Network

XG-MB67X_EN2_CD_k 06.5.12, 6:50 AM50

51

Usefu

lF

eatures

Troubleshooting with the “Help” menu

Utilizing the “Help” menu func-tions

This function advises you to solve the problems during usage.

• You can adjust the items with check marks ().• The items in the “Help” menu change, de-

pending on the input signal or setting that youhave selected.

• If the problem is not solved, refer to“Troubleshooting”. (See pages 59 and 60.)

• When selecting “sRGB” in "Picture Mode”, theitem “Color is faded or poor” is not displayed.This means you cannot change input signaltypes.

• When you select “Reset all adjustments to de-fault settings” and then press ENTER, thescreen for entering the password appears if apassword has been set. (See page 49.)

Press O or Q to adjust.

If the image is not improved, se-lect “Adjust horizontal noise.”,then press hENTER.

Select “Initiate “Auto Sync” Ad-justments”, then press hENTER.

Press P or R to select “Verticalstripes or flickering image ap-pears” on Help menu, then presshENTER.

Example: When image flickering appears

Operation to solve image flickering when pro-jecting the computer RGB signal.

3

4

5

6

There is no picture or audioVertical stripes or flickering image appearData image is not centeredColor is faded or poorPicture is darkThe image is distorted

Reset all adjustments to default settings

SEL. ENTER END

If there is no change after performing "Auto Sync"adjustments, adjust the following items.

Initiate “Auto Sync” Adjustments.

Help

Vertical stripes or flickering image appear

Vertical stripes or flickering image appear

Adjust vertical noiseAdjust horizontal noiseReset the 2 items aboveReturn

Cur. sig. freq: H 43 kHz / V 60 Hz

SEL. ENTER END

Pict. SCR Net.PRJ Help

Note

Press BMENU/HELP.1

2 Press O or Q to select “Help”, thenpress hENTER.


ENTER button

MENU/HELPbutton

0PhaseSEL./ADJ. Rtn. Menu END

Help

XG-MB67X_EN2_CD_k 06.5.12, 6:50 AM51

52

Cleaning the lens Use a commercially available blower or lens

cleaning paper (for glasses and camera lenses)for cleaning the lens. Do not use any liquid typecleaning agents, as they may wear off thecoating film on the surface of the lens.

As the surface of the lens can easily getdamaged, be sure not to scrape or hit the lens.

Cleaning the exhaust and intake vents Use a vacuum cleaner to clean dust from the

exhaust vent and the intake vent.

Cleaning the projector Ensure that you have unplugged the power

cord before cleaning the projector. The cabinet as well as the operation panel is

made of plastic. Avoid using benzene orthinner, as these can damage the finish on thecabinet.

Do not use volatile agents such as insecticideson the projector.Do not attach rubber or plastic items to theprojector for long periods.The effects of some of the agents in the plasticmay cause damage to the quality or finish of theprojector.

Wipe off dirt gently with a soft flannel cloth. When the dirt is hard to remove, soak a cloth in

a mild detergent diluted with water, wring thecloth well and then wipe the projector.Strong cleaning detergents may discolor, warpor damage the coating on the projector. Makesure to test on a small, inconspicuous area onthe projector before use.

Maintenance

Thinner

• If you want to clean the air vents during pro-jector operation, be sure to pressS STANDBY/ON on the projector oreSTANDBY on the remote control and putthe projector into standby mode. After thecooling fan has stopped, clean the vents.

Info

Wax

Mild detergent

Mild detergent dilutedwith water

XG-MB67X_EN2_CD_l 06.5.12, 6:51 AM52

53

Ap

pen

dix

Maintenance Indicators

About the lamp indicator

When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will bedisplayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp willautomatically turn off and then the projector will automatically enter standby mode. At this time, thelamp indicator will illuminate in red.

If you try to turn on the projector a fourth time without replacing the lamp, the projector willnot turn on.

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,“ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lampwill turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-tor will enter standby mode. After “ ” appears, be sure to perform the measures described on page54.

Lamp indicator

The warning lights (power indicator, lamp indicator and temperature warning indicator) on theprojector indicate problems inside the projector.

If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminatered, and the projector will enter standby mode. After the projector has entered standby mode,follow the procedures given below.

Temperature warning indicator

Power indicator

Lamp indicator

Red onPower indicator

Indicators on the Projector

Green on

Normal (Standby)

Normal (Power on)

Green on

Green blinks

Normal

The lamp is warming up or shutting down.

Temperature warningindicator

Off

Red on

Normal

The internal temperature is abnormallyhigh. (See page 54.)

Red blinks Abnormal (See page 54.)

Red on The lamp is shut down abnormally orrequires to be changed. (See page 54.)

Green blinks Normal (Cooling)

Top View

XG-MB67X_EN2_CD_l 06.5.12, 6:51 AM53

54

• If the temperature warning indicator illuminates, and the projector enters standby mode, follow thepossible solutions above and then wait until the projector has cooled down completely before plug-ging in the power cord and turning the power back on. (At least 10 minutes.)

• If the power is turned off for a brief moment due to power outage or some other cause while usingthe projector, and the power supply recovers immediately after that, the lamp indicator will illumi-nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,replace the power cord in the AC outlet and then turn the power on again.

• The cooling fan keeps the internal temperature of the projector constant and this function is con-trolled automatically. The sound of the cooling fan may change during operation because the fanspeed may change and this is not a malfunction.

• Do not unplug the power cord after the projector has entered standby mode and while the coolingfan is running. The cooling fan runs for about 90 seconds.

Maintenance indicatorProblem

The internaltemperature isabnormallyhigh.

The lamp doesnot illuminate.

Time to changethe lamp.

The lamp doesnot illuminate.

The powerindicator blinksin red when theprojector is on.

Cause

• Blocked air intake

• Cooling fanbreakdown

• Internal circuitfailure

• Clogged air intake

• The lamp is shutdown abnormally.

• Remaining lamp lifebecomes 5% orless.

• Burnt-out lamp• Lamp circuit failure

• The lamp unit coveris open.

Possible Solution

• Relocate the projector toan area with properventilation. (see page 8)

• Take the projector to yournearest Sharp AuthorizedProjector Dealer or ServiceCenter (see page 61) forrepair.

• Disconnect the power cordfrom the AC outlet, andthen connect it again.

• Carefully replace the lamp.(See page 56.)

• Take the projector to yournearest Sharp AuthorizedProjector Dealer or ServiceCenter (see page 61) forrepair.

• Please exercise care whenreplacing the lamp.

• Securely install the cover.

• If the power indicator blinksin red even when the lampunit cover is securelyinstalled, contact yournearest Sharp AuthorizedProjector Dealer or ServiceCenter (see page 61) foradvice.

Abnormal

Red on(Standby)

Red on

Red on(Standby)

Redblinks

Tempera-ture

warningindicator

Lampindicator

Powerindicator

Normal

Off

Green on(Greenblinks

when thelamp is

warmingup or

turningoff.)

Green on/Red on

Greenblinks

(Cooling)

Info

Maintenance Indicators (Continued)

XG-MB67X_EN2_CD_l 06.5.12, 6:51 AM54

55

Ap

pen

dix

Regarding the Lamp

Lamp It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes

5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life(percentage) can be checked with the on-screen display. (see page 47)

Purchase a replacement lamp of type AN-XR20LP from your place of purchase, nearest SharpAuthorized Projector Dealer or Service Center.

Caution Concerning the Lamp This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

failure can be attributed to numerous sources such as: excessive shock, improper cooling, surfacescratches or deterioration of the lamp due to a lapse of usage time.The period of time up to failure largely varies depending on the individual lamp and/or the conditionand the frequency of use. It is important to note that failure can often result in the bulb cracking.

When the lamp replacement indicator and on-screen display icon are illuminated, it is recommendedthat the lamp be replaced with a new one immediately, even if the lamp appears to be operatingnormally.

Should the lamp break, there is also a possibility that glass particles may spread inside of theprojector. In such a case, it is recommended you contact your nearest Sharp Authorized ProjectorDealer or Service Center to assure safe operation.

Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in thelamp may be vented into the room from the exhaust vent. Because the gas in this lamp includesmercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In caseof exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and maycause burn or injury.

Carefully change the lamp by following the instructions described in this section. * If you wish,you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or ServiceCenter.

* If the new lamp does not light after replacement, take your projector to the nearest Sharp AuthorizedProjector Dealer or Service Center for repair.

IMPORTANT NOTE TO U.S. CUSTOMERS:The lamp included with this projector is backed by a 90-day parts and labor limitedwarranty. All service of this projector under warranty, including lamp replacement,must be obtained through a Sharp Authorized Projector Dealer or Service Center.For the name of the nearest Sharp Authorized Projector Dealer or Service Center,please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp DisposalInformationwww.lamprecycle.org or 1-800-BE-SHARP U.S.A. ONLY

XG-MB67X_EN2_CD_l 06.5.12, 6:51 AM55

56

Removing and Installing theLamp Unit

• Make sure that you remove the lamp unit bythe handle. Do not touch the glass surface ofthe lamp unit or the inside of the projector.

• To avoid injury to yourself and damage to thelamp, be sure to carefully follow the stepsbelow.

• Do not loosen other screws except for thelamp unit cover and lamp unit.

Press SSTANDBY/ON on the pro-jector or eSTANDBY on the re-mote control to put the projectorinto standby mode.• Wait until the cooling fan stops.

Warning!• Do not remove the lamp unit from the projec-

tor right after use. The lamp and parts aroundthe lamp will be very hot and may cause burnsor injury.

Disconnect the power cord.• Unplug the power cord from the AC

socket.• Leave the lamp until it has fully cooled

down (about 1 hour).

Remove the lamp unit cover.• Turn the projector over. Loosen the user

service screw (1) that secures the lampunit cover. Remove the lamp unit cover(2).

1

2

Lamp unitAN-XR20LP

Info

Optionalaccessory

AC socket

User service screw(for lamp unit cover)

1

2

3

STANDBY/ON button

Regarding the Lamp (Continued)

XG-MB67X_EN2_CD_l 06.5.24, 1:53 PM56

57

Ap

pen

dix

Remove the lamp unit.• Loosen the securing screws from the

lamp unit. Hold the lamp unit by thehandle and pull it in the direction of thearrow. At this time, keep the lamp unithorizontal and do not tilt it.

Resetting the Lamp TimerReset the lamp timer after replacing the lamp.

Insert the new lamp unit.• Press the lamp unit firmly into the lamp

unit compartment. Fasten the securingscrews.

Replace the lamp unit cover.• Align the tab on the lamp unit cover

(1)and place it while pressing the tab(2) to close it. Then tighten the user ser-vice screw to secure the lamp unit cover.

4

5

6

Connect the power cord.• Plug the power cord into the AC socket

of the projector.

Reset the lamp timer.• While simultaneously holding downUMENU/HELP, TENTER and R on theprojector, press SSTANDBY/ON on theprojector.

• “LAMP 0000H” is displayed, indicatingthat the lamp timer is reset.

• Make sure to reset the lamp timer only whenreplacing the lamp. If you reset the lamp timerand continue to use the same lamp, this maycause the lamp to become damaged or ex-plode.

1

2

Info

AC socket

Securing screws

Handle

ENTER button

MENU/HELPbutton

R button

• If the lamp unit and lamp unit cover arenot correctly installed, the power will notturn on, even if the power cord is con-nected to the projector.

Info2

1

STANDBY/ONbutton

XG-MB67X_EN2_CD_l 06.5.24, 1:53 PM57

58

DTV

• When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.• Optimum image quality will be achieved by matching your computer’s output resolution to the

projector’s native resolution (1024 x 768).

Computer

Computer Compatibility Chart

• Multiple signal supportHorizontal Frequency: 15-70 kHz,Vertical Frequency: 45-85 Hz,Pixel Clock: 12-108 MHzSync signal:Compatible with TTL level

• Compatible with sync on green signalThe following is a list of modes that conform to VESA. However, this projector supports othersignals that are not VESA standards.

27.031.537.527.031.537.927.031.527.031.537.926.231.534.737.937.543.331.435.137.946.648.146.953.740.348.456.560.068.755.066.267.564.064.034.937.849.760.268.7

607085607085607060708550607072758550566070727585506070758560707560606760757575

640 × 350

640 × 400

720 × 350

720 × 400

640 × 480

800 × 600

1,024 × 768

1,152 × 864

1,280 × 1,0241,400 × 1,050

640 × 480800 × 600832 × 624

1,024 × 7681,152 × 870

MAC 13"

MAC 16"

PC

VGA

SVGA

XGA

SXGA

SXGA+VGA

XGASXGA

PC/MAC

MAC 19"MAC 21"

SVGA

Signal

480I

480P

540P

576I

576P

720P

1035I

1035I

1080I

1080I

Horizontal Frequency (kHz)

15.7

31.5

33.8

15.6

31.3

45.0

28.1

33.8

28.1

33.8

Vertical Frequency (Hz)

60

60

60

50

50

60

50

60

50

60

Note

• Compatible with the signals below inintelligent compression: SXGA, SXGA+

• Intelligent Compression and ExpansionSystem resizing technology

ResolutionHorizontal Frequency

(kHz)Vertical Frequency

(Hz) VESA Standard Display

Upscale

True

Intelligent Compression

Upscale

Intelligent CompressionTrue

XG-MB67X_EN2_CD_l 06.5.12, 6:51 AM58

59

Ap

pen

dix

Troubleshooting

No picture and no soundor projector does not

start.

Sound is heard but nopicture appears (or picture

is dark).

Color is faded or poor.

Picture is blurred;noise appears.

Picture appears but nosound is heard.

An unusual sound isoccasionally heard from

the cabinet.Maintenance indicator onthe projector illuminates

or blinks in red.

Problem Check

• Projector power cord is not plugged into the wall outlet.

• Power to the external connected devices is off.

• The selected input mode is wrong.

• Cables incorrectly connected to the projector.

• Remote control battery has run out.

• External output has not been set when connecting notebookcomputer.

• The lamp unit cover is not installed correctly.


• “Bright” is set to minimum position.

• Depending on the computer you are using, an image may not beprojected unless the signal output setting of the computer isswitched to the external output. Refer to the computer’s operationmanual for how to switch its signal output settings.

• Image adjustments are incorrectly set.• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower

the “Bright Boost” value.

(Video Input only)

• Video input system is incorrectly set.

• Adjust the focus.

• The projection distance exceeds the focus range.

(Computer Input only)

• Perform “Fine Sync” Adjustments (“Clock” Adjustment)

• Perform “Fine Sync” Adjustments (“Phase” Adjustment)

• Noise may appear depending on the computer.


• Volume is set to minimum.• When the projector is connected to an external device and the

volume is set to minimum, the sound is not output even if you turn upthe volume of the external device.

• “Speaker" is set to “Off”.

• If the picture is normal, the sound is due to cabinet shrinkagecaused by room temperature changes. This will not affect operationor performance.

• See “Maintenance Indicators”.

Page

27

–

32

23–27

15

23

56, 57

23–27

43

–

43

51

30

20

51

51

–

23–27

32

46

–

53

48The projector cannot beturned on or put into thestandby mode using theSTANDBY/ON button on

the projector.

• The keylock is set.If the keylock is set to “ON”, all the buttons are locked.

XG-MB67X_EN2_CD_l 06.5.12, 6:51 AM59

60

Problem

Picture is green onINPUT 1 (COMPONENT)/INPUT 2 (COMPONENT).

Picture is pink (no green)on INPUT 1 (RGB)/INPUT

2 (RGB).

Picture is too bright andwhitish.

The cooling fan becomesnoisy.

The lamp does not lightup even after the

projector turns on.

The lamp suddenly turnsoff during projection.

The image sometimesflickers.

The lamp needs muchtime to turn on.

Picture is dark.

Check

• Change the input signal type setting.• When you cannot select an input signal type, select “Color is faded

or poor” in the “Help” menu, after selecting an item other than“sRGB” in “Picture Mode”, and then select an input signal type.

• Image adjustments are incorrectly set.

• When temperature inside the projector increases, the cooling fanruns faster.

• The lamp indicator is illuminating in red.Replace the lamp.

• Cables incorrectly connected to the projector or the connectedequipment works improperly.

• Select “Vertical stripes or flickering image appear” in the “Help”menu and make the necessary adjustments.

• If this happens frequently, replace the lamp.

• The lamp will eventually need to be changed.While the remaining lamp life draws to a close, replace the lamp.

Page

5142, 51

43

–

53, 56

23–27

51

56

56

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operationor interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

Troubleshooting (Continued)

XG-MB67X_EN2_CD_l 06.5.12, 6:51 AM60

61

Ap

pen

dix

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, firstrefer to the “Troubleshooting” section on pages 59 and 60. If this operation manualdoes not answer your question, please contact the SHARP Service departmentslisted below.

U.S.A. Sharp Electronics Corporation1-888-GO-SHARP (1-888-467-4277)[email protected]://www.sharp-usa.com

Canada Sharp Electronics of Canada Ltd.(905) 568-7140http://www.sharp.ca

Mexico Sharp Electronics CorporationMexico Branch(525) 716-9000http://www.sharp.com.mx

Latin America Sharp Electronics Corp. LatinAmerican Group(305) [email protected]://www.siempresharp.com

Germany Sharp Electronics (Europe) GMBH01805-234675http://www.sharp.de

U.K. Sharp Electronics (U.K.) Ltd.08705 274 [email protected]://www.sharp.co.uk

Italy Sharp Electronics (Italy) S.P.A.(39) 02-89595-1http://www.sharp.it

France Sharp Electronics France01 49 90 35 [email protected]://www.sharp.fr

Spain Sharp Electronica Espana, S.A.93 [email protected]://www.sharp.es

Switzerland Sharp Electronics (Schweiz) AG0041 1 846 63 [email protected]://www.sharp.ch

Sweden Sharp Electronics ( Nordic ) AB(46) 8 [email protected]://www.sharp.se

Austria Sharp Electronics (Europe) GMBHBranch Office Austria0043 1 727 19 [email protected]://www.sharp.at

Benelux SHARP Electronics Benelux BV0900-SHARPCE (0900-7427723)Nederland9900-0159 Belgiumhttp://www.sharp.nlhttp://www.sharp.behttp://www.sharp.lu

Australia Sharp Corporation of Australia Pty.Ltd.1300-135-022http://www.sharp.net.au

New Zealand Sharp Corporation of New Zealand(09) 634-2059, (09) 636-6972http://www.sharp.net.nz

Singapore Sharp-Roxy Sales (S) Pte. [email protected]://www.sharp.com.sg

Hong Kong Sharp-Roxy (HK) Ltd.(852) [email protected]://www.sharp.com.hk

Taiwan Sharp Corporation (Taiwan)0800-025111http://www.sharp-scot.com.tw

Malaysia Sharp-Roxy Sales & Service Co.(60) 3-5125678

U.A.E. Sharp Middle East [email protected]

Thailand Sharp Thebnakorn Co. [email protected]://www.sharp-th.com

Korea Sharp Electronics Incorporated ofKorea(82) [email protected]://www.sharpkorea.co.kr

India Sharp Business Systems (India)Limited(91) 11- [email protected]

XG-MB67X_EN2_CD_m 06.5.12, 6:52 AM61

62

Specifications

ProjectorXG-MB67XNTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas InstrumentsPanel size: 0.55" (14 mm), 1chip XGA DMDNo. of dots: 786,432 dots (1,024 [H] × 768 [V])1–1.15 × zoom lens, F2.4–2.6, f = 18.7–21.5 mm300 W DC lamp15-pin mini D-sub connectorY: 1.0 Vp-p, sync negative, 75 Ω terminatedPB: 0.7 Vp-p, 75 Ω terminatedPR: 0.7 Vp-p, 75 Ω terminated600 TV lines (DTV720P)15-pin mini D-sub connectorRGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminatedHORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)VERTICAL SYNC. SIGNAL: Same as above4-pin mini DIN connectorY (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminatedC (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminatedRCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ωterminated45–85 Hz15–70 kHz12–108 MHz9-pin mini DIN connector8-pin RJ-45 modular connectorø3.5 mm minijack or RCA terminal: 0.5 Vrms, more than 22 kΩ (stereo)ø3.5 mm minijack: 0.5 Vrms, less than 2.2 kΩ

4 cm × 2.85 cm oval × 1AC 110–240 V3.6 A50/60 Hz385 W (Lamp Setting “Bright”)/308 W (Lamp Setting “Eco + Quiet”) with AC 110 V367 W (Lamp Setting “Bright”)/300 W (Lamp Setting “Eco + Quiet”) with AC 240 V9.3 W (AC 110 V) – 10.0 W (AC 240 V)1,450 BTU/hour (Lamp Setting “Bright”)/1,160 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 110 V1,380 BTU/hour (Lamp Setting “Bright”)/1,130 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 240 V41°F to 95°F (+5°C to +35°C)–4°F to 140°F (–20°C to +60°C)Plastic38 kHz12 13/32" × 4 19/64" × 11 1/32" (315 (W) × 109 (H) × 280 (D) mm) (main body only)12 13/32" × 4 47/64" × 11 37/64" (315 (W) × 120 (H) × 294 (D) mm) (including adjust-ment foot and projecting parts)8.6 lbs. (3.9 kg)Remote control, Power cord for U.S. and Canada, etc., Power cord for Europe,except U.K., Power cord for U.K. and Singapore, Power cord for Australia, NewZealand and Oceania, RGB cable, DIN-D-sub RS-232C adaptor, Operationmanual (Printed and CD-ROM)

Product typeModel

Video system

Display methodDMD panel

LensProjection lamp

Component input signal(INPUT1/2)

Horizontal resolutionComputer RGB input

(INPUT 1/2)/output(OUTPUT) signal

S-video input signal(INPUT 3)

Video input signal(INPUT 4)

Vertical frequencyHorizontal frequency

Pixel clockRS-232C terminal

LAN terminalAudio input signal

Audio output signal(AUDIO OUTPUT 1-4)

Speaker systemRated voltageInput current

Rated frequencyPower consumption

Power consumption (standby)Heat dissipation

Operating temperatureStorage temperature

CabinetI/R carrier frequency

Dimensions (approx.)

Weight (approx.)Replacement parts

As a part of policy of continuous improvement, SHARP reserves the right to make design andspecification changes for product improvement without prior notice. The performance specifica-tion figures indicated are nominal values of production units. There may be some deviations fromthese values in individual units.

XG-MB67X_EN2_CD_m 06.5.12, 6:52 AM62

63

Ap

pen

dix

Dimensions

Units: inches (mm)

12 13/32 (315)

3 1/16 (77.5)

2 19/32

(65.5)1 53/64

(46.2)

3 5/32 (80)

1 55

/64 (4

7)2

7 /8 (7

3)

2 61/64

(75)

1 11/32 (33.8)

4 19

/64 (1

09)

1 7 /

8 (4

7.5)

4 7 /

64 (1

04)

7 /16

(11)

11 1 /

32 (2

80)

23/6

4 (9

)13

/64 (5

)7 /

16 (1

1)

ø9 7/64 (69.2)

XG-MB67X_EN2_CD_m 06.5.12, 6:52 AM63

64

AC socket ....................................................... 27Accessories ................................................... 11Adjustment buttons ........................................ 40Adjust horizontal noise ........................... 39, 51Adjust vertical noise ............................... 39, 51Aspect ratio ....................................................34AUDIO INPUT terminal .................... 23, 24, 25AUDIO OUTPUT terminal ............................. 21Auto Keystone Correction .............................. 44Auto Power Off ............................................... 46Auto Search ................................................... 46Auto Sync

(Auto Sync adjustment) ........... 36, 39, 46, 51AUTO SYNC button ....................................... 36AV MUTE button ............................................ 32

BACK button .................................................. 14Background ....................................................45Blue ................................................................ 43BORDER ................................................ 34, 35BREAK TIMER button ...................................36Bright ............................................................. 43Bright Boost ................................................... 43

Clock ..............................................................51CLR Temp (Color Temperature) .................... 43Color ..............................................................43Contrast ......................................................... 43

DHCP Client .................................................. 50DIN-D-sub RS-232C adaptor ........................ 26

ENTER button ................................................ 40Exhaust vent ........................................... 13, 52

Fan Mode ....................................................... 47Fine Sync ....................................................... 51Focus ring ...................................................... 30FORWARD button ......................................... 14FREEZE button ............................................. 36Front adjustment foot ..................................... 31

H-Pos ...................................................... 39, 51HEIGHT ADJUST lever ................................. 31Help ................................................................ 51

Image shift ..................................................... 44INPUT 1 terminal .............................. 23, 24, 25INPUT 1 – 4 modes ....................................... 32INPUT 2 terminal .............................. 23, 24, 25INPUT 3 terminal ........................................... 24INPUT 4 terminal ........................................... 25INPUT buttons ............................................... 32Intake vent ........................................ 12, 13, 52

Kensington SecurityStandard connector .................................... 13

Keycode ......................................................... 47Keylock ........................................................... 48KEYSTONE button ........................................ 33Keystone Correction ...................................... 44

Lamp ....................................................... 11, 55

Index

Lamp indicator ............................................... 53Lamp Setting ................................................. 43Lamp Timer (Life) .......................................... 47Lamp unit ....................................................... 56LAN terminal .................................................. 27Language (on-screen display language) ...... 45Lens Cap ....................................................... 12

MAC Address ................................................. 50MENU/HELP button ................................ 40, 51

Network .......................................................... 50NORMAL ................................................ 34, 35

ON button ......................................................28Optional accessories .....................................11OSD Display .................................................. 45OUTPUT (INPUT1, 2) terminal ..................... 25

Password ....................................................... 49PDF ................................................................10Phase ............................................................. 51Picture Adjustment ........................................ 42Picture Mode .......................................... 36, 42PICTURE MODE button ................................ 36Power cord ..................................................... 27PRJ - ADJ ......................................................46PRJ Mode ............................................... 19, 45Progressive ....................................................43

R-6 batteries .................................................. 15Rear adjustment foot .....................................31Red ................................................................43Remote control .............................................. 14Remote control sensor .................................. 15Replacing the lamp ................................. 55, 56Resize ..................................................... 34, 44RESIZE button ............................................... 34RETURN button ............................................. 40RGB cable ..................................................... 23RS-232C terminal .......................................... 26

SCR - ADJ ..................................................... 44Screen Size and Projection Distance ...................... 20Setup Guide ............................................ 30, 45Sharp ............................................................. 43Speaker .......................................................... 46STANDBY button ........................................... 29STANDBY/ON button .............................. 28, 29STRETCH ............................................... 34, 35Supplied accessories .................................... 11System Lock .................................................. 47System Sound ............................................... 46

TCP/IP ........................................................... 50Temperature warning indicator ...................... 53Tint ................................................................. 43

Video System ................................................ 39Volume buttons .............................................. 32V-Pos ....................................................... 39, 51

Zoom ring ....................................................... 30

XG-MB67X_EN2_CD_m 06.5.19, 11:29 AM64

XG-MB67X_EN2_CD__cover 06.5.12, 6:53 AM6

XG-MB67X Operation Manual · O CD-ROM fornecido contém instruções de operação em Inglês,...

Documents

Transcript of XG-MB67X Operation Manual · O CD-ROM fornecido contém instruções de operação em Inglês,...