Post on 08-Apr-2016
Universidade Federal do Rio Grande do Sul
Programa de Pós-Graduação em Ciência dos Materiais
AVALIAÇÃO DAS PROPRIEDADES FÍSICO-QUÍMICAS,
MECÂNICAS E TRIBOLÓGICAS DE FILMES FINOS
DE VC, Si3N4 E TiN/Ti
Cesar Aguzzoli
Tese de Doutorado
Porto Alegre, agosto de 2011
ii
Universidade Federal do Rio Grande do Sul
Programa de Pós-Graduação em Ciência dos Materiais
AVALIAÇÃO DAS PROPRIEDADES FÍSICO-QUÍMICAS,
MECÂNICAS E TRIBOLÓGICAS DE FILMES FINOS
DE VC, Si3N4 E TiN/Ti
Cesar Aguzzoli
Tese realizada sob a orientação do Prof. Dr. Israel Baumvol, apresentada ao Programa de Pós-Graduação em Ciência dos Materiais da Universidade Federal do Rio Grande do Sul em preenchimento parcial dos requisitos para a obtenção do título de Doutor em Ciência dos Materiais.
Porto Alegre 2011
iii
Agradecimentos
Ao Prof. Israel pelo seu empenho incansável em ensinar, orientar, exigir; pela sua
determinação em conduzir todo e qualquer meio necessário para que as pesquisas sejam
realizadas. Um modelo de pesquisador, um grande amigo e uma excelente pessoa;
A minha família pelo apoio, compreensão e amor;
Ao meu amor, Patrícia, pelo seu carinho, amor e companheirismo;
Aos professores e amigos: Carlos Figueroa, Gabriel Soares;
A Marga, a qual com seu empenho e dedicação contribuiu para a realização deste trabalho,
uma grande pessoa, uma grande profissional e uma grande amiga;
Ao Paulinho que contribuiu para este trabalho com seu grande empenho e genialidade;
Aos amigos e colegas dos laboratórios da UFRGS e UCS.
A todos que contribuíram direta e indiretamente e que não foram citados.
iv
Lista de trabalhos gerados a partir dos resultados descritos na Tese [1] Portolan, E.; Amorim, C.L.G.; Soares, G.V.; Aguzzoli, C.; Perottoni, C.A.; Baumvol, I.J.R.; Figueroa, C.A.; Thin Solid Films, Carbon occupancy of interstitial sites in vanadium carbide films deposited by direct current reactive magnetron sputtering, 2009, 517, 6493. [2] Aguzzoli, C.; Figueroa, C.A.; Soares, G.V.; Baumvol, I.J.R.; J. Mater. Sci., Physicochemical and structural characteristics of TiC and VC thin films deposited by DC reactive magnetron sputtering, 2010, 45, 4994. [3] Aguzzoli, C.; Figueroa, C.A.; de Souza, F.S.; Spinelli, A.; Baumvol, I.J.R.; Corrosion and nanomechanical properties of vanadium carbide thin film coatings of tool steel. Submetido. [4] Aguzzoli, C.; Marin, C.; Figueroa, C.A.; Soares, G.V.; Baumvol, I.J.R.; J. Appl. Phys., Physicochemical, structural, and mechanical properties of Si3N4 films annealed in O2, 2010, 107, 073521. [5] Filla, J.; Aguzzoli, C.; Sonda, V.; Farias, M.C.M.; Soares, G.V.; Baumvol, I.J.R.; Figueroa, C.A.; Surf. Coat. Technol., Nanoscale friction of partially oxidized silicon nitride thin films, 2011, 205, 4528. [6] Aguzzoli, C.; Tentardini, E.K.; Figueroa, C.A.; Kwietniewski, C.; Miotti, L.; Baumvol, I.J.R.; Appl. Phys. A, Atomic transport and chemical reaction in TiN/Ti nanolayers on plasma nitrided steel, 2009, 94, 263.
v
Sumário
Lista de trabalhos gerados a partir dos resultados descritos na Tese ........................................ iv
Lista de Figuras ........................................................................................................................ vii
Abreviaturas .............................................................................................................................. ix
Resumo ....................................................................................................................................... x
Abstract ..................................................................................................................................... xi
1. INTRODUÇÃO .................................................................................................................. 1
2. Métodos experimentais ..................................................................................................... 7
2.1. Preparação de amostras ............................................................................................... 7
2.2. Método de deposição ................................................................................................... 7
2.2.1. Pulverização catódica (sputtering) ....................................................................... 7
2.3. Técnicas de análise .................................................................................................... 11
2.3.1. Espectrometria de retroespalhamento Rutherford (RBS) ................................... 11
2.3.2. Espalhamento de íons com energia média (MEIS) ............................................ 13
2.3.3. Espalhamento de íons com energia baixa (LEIS) .............................................. 15
2.3.4. Perfilometria de concentração utilizando reação nuclear ressonante estreita (NRP) 17
2.3.5. Espectroscopia de fotoelétrons induzidos por raios X (XPS) ............................ 19
2.3.6. Difração de raios X (XRD) ................................................................................ 22
2.3.7. Reflectometria de raios X (XRR) ....................................................................... 23
2.3.8. Nanoindentação .................................................................................................. 25
2.3.9. Pino no disco ...................................................................................................... 28
2.3.10. Coeficiente de atrito ........................................................................................... 29
3. Carbeto de vanádio ......................................................................................................... 32
3.1. Corrosão..................................................................................................................... 37
3.1.1. Polarização cíclica .............................................................................................. 39
3.1.2. Espectroscopia de impedância eletroquímica .................................................... 40
3.1.3. Diagrama de Nyquist .......................................................................................... 42
3.1.4. Soluções e condições de trabalho ....................................................................... 43
3.1.5. Célula, eletrodos e corpos de prova ................................................................... 43
3.1.6. Instrumentação ................................................................................................... 44
3.1.7. Procedimentos .................................................................................................... 45
vi
3.2. Corrosão de filmes de VC ......................................................................................... 45
3.3. Discussão dos resultados de corrosão ........................................................................ 49
3.4. Conclusões Parciais ................................................................................................... 50
4. Nitreto de silício ............................................................................................................... 53
4.1. Composição elementar e taxa de deposição .............................................................. 56
4.2. Cristalografia e densidade real .................................................................................. 57
4.3. Propriedades mecânicas e tratamento térmico ........................................................... 57
4.4. Perfis de concentração em profundidade de oxigênio e nitrogênio após annealing em 18O2 e composição dos filmes ............................................................................................... 59
4.5. Atrito em escala nanoscópica .................................................................................... 59
4.6. Conclusões parciais ................................................................................................... 61
5. Nitreto de titânio sobre titânio ....................................................................................... 63
5.1. Resultados experimentais .......................................................................................... 66
5.2. Conclusões parciais ................................................................................................... 68
6. Conclusões finais e perspectivas .................................................................................... 70
REFERÊNCIAS BIBLIOGRÁFICAS ..................................................................................... 74
vii
Lista de Figuras
Figura 1 – Etapas para a preparação das amostras utilizadas neste trabalho. ............................ 7 Figura 2 – Efeitos de partículas energéticas em superfícies. ...................................................... 8 Figura 3 – Sputtering em três energias diferentes. (a) baixa, (b) e (c) alta energia. .................. 9 Figura 4 – Influência da energia no rendimento no processo de sputtering. ........................... 10 Figura 5 – Espectro de retroespalhamento Rutherford esquemático para um filme fino AB sobre um substrato leve C. ....................................................................................................... 11 Figura 6 – Esquema de vários processos de perda de energia para retroespalhamento a partir da superfície da amostra e ao longo da amostra. Energia é perdida por transferência de momento entre a partícula do feixe e da amostra e com a partícula incidente que atravessa o alvo antes e depois do espalhamento. ....................................................................................... 12 Figura 7 – Analisador da técnica de MEIS .............................................................................. 14 Figura 8 – Espectro equemático de MEIS. ............................................................................... 15 Figura 9 – Geometria de análise de LEIS e do analisador eletrostático de energia. ................ 16 Figura 10 – Espectros de He retroespalhado para as técnicas de LEIS e RBS para uma amostra de Si com Ag, Si e O na superfície. ......................................................................................... 17 Figura 11 – Seção de choque diferencial em função da energia de incidência dos prótons. ... 18 Figura 12 – Detecção das reações nucleares (a) na superfície do material, (b) ao longo da amostra e (c) na profundidade da amostra. .............................................................................. 19 Figura 13 – Técnica de XPS: (a) irradiação da amostra pelo feixe e (b) fóton arrancando elétron do nível interno. ........................................................................................................... 21 Figura 14 – Espectro de Ti em diferentes estados. ................................................................... 21 Figura 15 – Itens que compões um equipamento de difração de raios X. ................................ 22 Figura 16 – Esquema da técnica de XRR. ................................................................................ 24 Figura 17 – Espectro típico de XRR. ....................................................................................... 25 Figura 18 – Esquema da ponta de penetração em um equipamento de nanoindentação. ........ 26 Figura 19 – Representação de carga e descarga do penetrador em função da profundidade. .. 27 Figura 20 – (a) representação esquemática de ensaio pino no disco e (b) equipamento de pino-no-disco. ................................................................................................................................... 28 Figura 21 – Estrutura cristalina de VC. .................................................................................... 32 Figura 22 – Diagrama de fases do sistema V-C. ...................................................................... 33 Figura 23 – Volume de desgaste versus tempo de deposição. ................................................. 37 Figura 24 – (a) arranjo experimental e (b) célula eletroquímica típicos de ensaios de corrosão. .................................................................................................................................................. 39 Figura 25 – (a) Variação do potencial com o tempo e (b) curva resultante da corrente por potencial em um voltamograma cíclico típico. ........................................................................ 40 Figura 26 – Diagrama de Nyquist, com o vetor de impedância para um sistema eletroquímico simples. ..................................................................................................................................... 43 Figura 27 – (a) Eletrodos utilizados e (b) célula eletroquímica para ensaios de corrosão. ...... 44 Figura 28 – (a) EIS e (b) voltametria cíclica de filmes finos de VC sobre aço, variando a composição do plasma. ............................................................................................................ 46
viii
Figura 29 – (a) EIS e (b) voltametria cíclica de filmes finos de VC sobre aço, variando a temperatura do substrato durante a deposição. ......................................................................... 47 Figura 30 – Microscopia eletrônica de varredura de filme fino de VC sobre aço AISI H12, após corrosão em solução de 3,5% de NaCl. As imagens mostram os pites (a) e detalhe dos pites expondo o substrato (b). .................................................................................................. 48 Figura 31 – Espectro de espalhamento Raman para filmes de VC com diferentes composições à 20 °C. ..................................................................................................................................... 49 Figura 32 – Variação da dureza para os revestimentos TiN, CrN, TiAlN e CrAlN (indicados na legenda) depositados por PVD, após o tratamento térmico em diferentes temperaturas. Os pontos em 25 °C referem-se a revestimentos sem tratamento térmico. ................................... 54 Figura 33 – Diagrama de fases para o sistema N-Si. ............................................................... 55 Figura 34 – Diagrama de fases para o sistema N-Ti. ............................................................... 63 Figura 35 – Estrutura de TiN com camada intermediária de Ti sobre aço nitretado. .............. 64 Figura 36 – Estruturas estudadas no presente trabalho. ........................................................... 65
ix
Abreviaturas
Ecorr – potencial de circuito aberto
Epit – potencial de pite
Epro – potencial de proteção ou repassivação
EIS – espectroscopia de impedância eletroquímica (Electrochemical Impedance
Spectroscopy)
GAXRD – difração de raios X de baixo ângulo
H3/E2 – resistência a deformação plástica / resistência ao desgaste
LEIS – espalhamento de íons com energia baixa
MEIS – espalhamento de íons com energia média
NRP – perfilometria de concentração utilizando reação nuclear ressonante estreita
PVD – physical vapor deposition
RBS – espectrometria de retroespalhamento Rutherford
SCE – eletrodo de calomelano saturado
Si3N4 – nitreto de silício
Sputtering – pulverização catódica
TiN – nitreto de titânio
VC – carbeto de vanádio
XPS – espectroscopia de fotoelétrons induzidos por raios X
XRD – difração de raios X
XRR – reflectometria de raios X
Z – impedância
x
Resumo
Neste trabalho foram estudadas correlações entre estrutura e propriedades de certos
revestimentos baseados em filmes finos cerâmicos, mais especificamente carbeto de vanádio,
nitreto de silício e nitreto de titânio sobre titânio. As condições e parâmetros de deposição dos
filmes, tais como composição e fluxo dos gases reativos, temperatura do substrato e outras,
foram variados para obter filmes com composições, densidades e espessuras convenientes. As
características físico-químicas dos filmes foram determinadas mediante a utilização de um
grande número de ferramentas analíticas, descritas no texto. A avaliação do comportamento
mecânico, tribológico e de resistência à corrosão dos filmes também foram determinadas por
um apreciável número de métodos, os quais são descritos em detalhes no texto. Os resultados
indicam algumas correlações importantes entre dureza, resistência ao desgaste e resistência à
corrosão por um lado, e composição, densidade real e estrutura cristalina, por outro lado. Da
mesma forma, foi possível estabelecer fatos novos sobre a adesão de filmes finos a substratos
de aço e o transporte de diferentes espécies químicas envolvidas através de estruturas
TiN/Ti/aço nitretado. Perspectivas para a continuidade do trabalho de pesquisa aqui relatado
são discutidas no capítulo de Conclusões.
xi
Abstract
We report here on the investigation of correlations between structure and properties of
certain coatings based on ceramic thin films, more specifically vanadium carbide, silicon
nitride and titanium nitride on titanium. The films deposition conditions and parameters, such
as the reactive gases compositions and flux, the substrate temperature during deposition and
others, were varied in order to obtain films with convenient composition, density and
thickness. The physicochemical characteristics of the films were determined by a large
number of analytical techniques, as described in the text. The evaluation of the mechanical,
tribologic, and corrosion behavior of the thin film coatings was also determined by a
substantial number of techniques, all described in the text. The results indicate some
important correlations between hardness, wear and corrosion resistance on one hand, and
composition, real density, and crystalline structure on the other hand. In the same lines, it was
possible to establish new facts about adhesion of thin film coatings on steel substrates and the
transport of the involved chemical species across TiN/Ti/nitrided steel structures. The
prospects for continuations of this work are discussed in the Conclusões chapter.
1
CAPÍTULO 1
1. INTRODUÇÃO
Neste trabalho investigamos características físico-químicas, mecânicas, tribológicas e
corrosivas de alguns revestimentos protetores de filmes finos de interesse prático. Os filmes
que fizeram o objeto do presente estudo são carbeto de vanádio sobre aço (VC/aço), nitreto de
silício sobre silício (Si3N4/Si), nitreto de titânio sobre aço (TiN/aço nitretado a plasma) e
nitreto de titânio sobre titânio sobre aço nitretado a plasma (TiN/Ti/aço nitretado a plasma).
Entre as características investigadas mencionamos aqui a composição química elementar dos
filmes, a distribuição em profundidade dos diferentes elementos químicos, a estrutura
cristalográfica, os compostos químicos formados nos filmes, a densidade real dos filmes,
juntamente com a nanodureza, o módulo de elasticidade a ela associado, a tensão elástica até
ruptura, o coeficiente de atrito, a taxa de desgaste, a corrosão e a adesão.
O objetivo principal é estabelecer correlações entre características físico-químicas dos
filmes e suas propriedades mecânicas, tribológicas e corrosivas, bem como correlações entre
características físico-químicas da interface filme/substrato e a adesão dos filmes ao substrato.
A literatura científica carece de tais correlações, especialmente daquelas bem
estabelecidas, pois a grande maioria das publicações trata somente dos aspectos físico-
químicos, ou somente dos aspectos mecânicos ou tribológicos, ou de corrosão, ou adesivos.
Para o aperfeiçoamento ou otimização de revestimentos protetores de aplicação industrial, é
crucial estabelecermos bases científicas confiáveis para o comportamento destes materiais em
que mais de uma propriedade atua. Esta é a contribuição que pretende aportar este trabalho.
Para que se tenha um melhor entendimento da razão de utilização de certos filmes finos
no presente trabalho, algumas considerações devem ser feitas. Nos próximos parágrafos são
2
descritos alguns revestimentos e técnicas atuais referentes à engenharia de superfícies e
revestimentos protetores para a utilização na indústria metal-mecânica.
Nas últimas décadas, a engenharia de superfícies vem se destacando pelas suas
aplicações em inúmeras áreas, entre elas a metalurgia fina, a microeletrônica, os biomateriais,
e outras [1,2]. Dentro da engenharia de superfícies, um dos processos amplamente utilizado é
o revestimento protetor por filmes finos, o qual a indústria metal-mecânica está utilizando em
grande escala [3,4]. Esses filmes finos podem ser depositados sobre o material comumente
utilizado para a confecção de ferramentas e moldes, aumentando a velocidade de avanço e a
vida útil dos mesmos, evitando assim o gasto nas operações de troca e obtendo diversos
ganhos de desempenho.
Entre os revestimentos protetores, o nitreto de titânio (TiN) vem sendo estudado e
utilizado há décadas e na indústria metal-mecânica é empregado em ferramentas e moldes,
devido a suas ótimas propriedades mecânicas e tribológicas [5,6]. No entanto, este
revestimento possui algumas limitações, tais como, degradação em temperaturas em torno de
800°C, coeficiente de atrito apreciável e baixa resistência à corrosão. Estas deficiências
motivaram a busca de novos revestimentos para a substituição do TiN [7]. Um dos objetivos
do presente trabalho é o estudo de diferentes revestimentos, tais como, VC e Si3N4, para a
possível substituição do TiN em processos e ferramentas para a indústria metal-mecânica
[8,9].
As condições de uso às quais são submetidos os componentes revestidos,
principalmente as ferramentas, estão sendo cada vez mais severas em relação ao desgaste
abrasivo e solicitação mecânica. Devido a isso, os revestimentos devem cumprir alguns
requisitos para a sua utilização prática [5]. Alguns desses requisitos são: propriedades
mecânicas e tribológicas estáveis a temperaturas acima de 800°C, adesão do filme ao
3
substrato, resistência à corrosão e outras. Os revestimentos utilizados ultimamente cumprem
com pelo menos um dos requisitos citados. Estudos recentes mostram que é possível obter
revestimentos que possuam vários desses requisitos.
Atualmente, os revestimentos que estão ganhando maior interesse dos estudos são
estruturas do tipo multicamada, tais como, TiN/VN, TiN/ZrN, TiAlN/VN [10,11]. Essas
estruturas são confeccionadas de maneira que cada monocamada possua espessuras na ordem
de nanometros e repetidas centenas de vezes uma após a outra, dependendo da espessura final
que se deseja. O objetivo principal da utilização dessas estruturas é o aumento significativo da
dureza, que em alguns casos pode chegar a valores superiores a 50 GPa [12], pois as
multicamadas induzem diversos efeitos nanoestruturais que ainda não foram completamente
explicados, mas que na prática observa-se um aumento de dureza e resistência ao desgaste.
Revestimentos de aços com filmes finos tais como VC e Si3N4 tem sido bastante
investigados por apresentarem boas características de adesão, dureza-desgaste e resistência à
corrosão [8,9].
Outras estruturas que estão sendo estudadas são os nanocompósitos de diversos
materiais em matrizes amorfas, por exemplo, TiC/a-C, nc-TiN/a-Si3N4, nc-TiB/a-Si3N4 [13].
A característica que apresenta o maior aumento em seu valor é a dureza, a qual em
determinadas estruturas pode ultrapassar 100 GPa [13]. Nessas estruturas, a principal
característica desejada é o tamanho controlado dos nanocristais, parâmetro que está sendo
otimizado para conferir essa dureza elevada. Outra propriedade investigada é a estabilidade da
dureza em temperaturas acima de 1000 °C, o que é interessante para os processos de
usinagem a seco que facilmente atingem temperaturas desta ordem. Estes revestimentos estão
começando a ser estudados, o Si3N4 sendo um bom exemplo e existe ainda muito trabalho
4
para ser feito como a seleção de materiais para as estruturas, otimização do tamanho dos
nanocristais, distribuição dos nanocristais na matriz, entre outras.
Para a indústria metal-mecânica, esses revestimentos estão longe de se tornarem
comuns, um dos principais motivos é o alto custo de deposição destas estruturas, além da
necessidade no avanço dos estudos para que esses revestimentos possuam uma boa adesão ao
substrato [14]. Com o estudo aprofundado dessas estruturas, as ferramentas na indústria
metal-mecânica terão maior resistência ao desgaste abrasivo, uma maior velocidade de avanço
e uma maior resistência à corrosão. Todas essas características contribuirão para um ganho na
vida útil da ferramenta, fazendo com que a mesma tenha que ser substituída com menor
frequência. No atual momento, a utilização de filmes monocamadas, como os estudados por
este trabalho, são a realidade dos revestimentos na indústria metal-mecânica e, portanto torna-
se essencial o conhecimentos das relações existentes entre as suas características para a sua
compreensão científica e técnica visando a utilização industrial.
No presente trabalho, foram investigados os parâmetros de deposição, a composição
química, o perfil de concentração em profundidade das diferentes espécies químicas, a
uniformidade, as características estruturais e o comportamento mecânico (dureza), tribológico
e corrosivo de filmes finos de VC, Si3N4, e TiN. A pressão parcial dos gases reativos, bem
como a temperatura do substrato foram os parâmetros variados na preparação de diferentes
amostras do mesmo filme.
Primeiramente, foram investigados filmes de VC. Determinamos a estrutura cristalina e
a estequiometria média de filmes finos de VC variando a pressão parcial do gás reativo e a
temperatura do substrato durante a deposição. Este estudo permitiu determinar a influência
destes parâmetros na estrutura cristalina de filmes de VC. Assim também, foi avaliada a
5
posição dos átomos de carbono nas estruturas de filmes de VC o que influência a estabilidade
da estrutura cristalina dos filmes.
Após, foram estudadas a taxa de deposição e a concentração versus profundidade
(perfilometria) do C, a dureza e módulo de elasticidade, o ambiente químico próximo da
superfície dos filmes e a taxa de desgaste. Finalmente, estudou-se o comportamento de filmes
de VC frente à corrosão. Neste último estudo, foi possível estabelecer correlações sólidas
entre propriedades físico-químicas dos filmes e seu comportamento frente à corrosão.
A seguir, foram estudados os filmes finos de Si3N4. Neste estudo foram variadas: i) a
temperatura do substrato durante a deposição, ii) a pressão parcial do gás reativo (N2) e iii) a
espessura dos filmes. Foi determinada a dependência da composição e da taxa de deposição
frente aos parâmetros i) e ii) acima. Em seguida, foi analisada a influência que a temperatura
do substrato durante a deposição exerce na estrutura cristalina destes filmes. Na sequência, a
avaliação da dureza e módulo de Young por nanoindentação. Finalizando o estudo, foi
realizado tratamento térmico das amostras em atmosfera de oxigênio até 1000 ºC, temperatura
típica que pode ser atingida durante o processo de usinagem a seco. Para o tratamento
térmico, foi utilizado um forno a vácuo com atmosfera controlada que permite a oxidação das
amostras à alta temperatura. Nessas amostras foi determinado o perfil de concentração de
oxigênio e nitrogênio, bem como as ligações químicas presentes. Finalmente, foi feito um
estudo detalhado do coeficiente de atrito em presença de cargas muito leves.
A estabilidade térmica da dureza dos filmes de Si3N4 até 1000 °C e o bom
comportamento potencial frente ao atrito e desgaste são correlacionados aqui com as
características físico-químicas descritas.
Finalmente, foram estudados o transporte de átomos através de interfaces de estruturas
do tipo TiN/aço nitretado e TiN/Ti/aço nitretado utilizando um traçador isotópico para o
6
transporte de N. Assim, também foram determinadas as composições químicas destas
interfaces. Neste trabalho foi utilizado um traçador isotópico (15N) para avaliar a migração
desta espécie química ao longo do filme e através das interfaces. Foi necessário utilizar esse
isótopo para diferenciar o nitrogênio da nitretação a plasma com aquele do filme depositado.
O objetivo deste estudo foi tentar relacionar a adesão de filmes de TiN sobre aços com
os estudos de transporte atômico dos diferentes elementos e a composição das interfaces. Da
mesma forma, tentou-se esclarecer a influência da camada intermediaria de Ti na adesão.
Estas correlações podem e devem ser estabelecidas porque a adesão é um fenômeno de
interface.
Este trabalho busca contribuir para estabelecer correlações entre estrutura e
propriedades dos materiais envolvidos. As ferramentas analíticas aqui utilizadas, avançadas e
variadas, são capazes de fornecer informações que não podem ser obtidas por outros métodos,
entre as quais mencionamos as reações nucleares ressonantes, os traçadores isotópicos e o
espalhamento de íons a baixíssimas energias. Estes métodos, juntamente com as
determinações de nano-dureza, módulo de elasticidade, coeficientes de atrito e desgaste e
corrosão permitiram contribuir para o objetivo geral, ou seja, estabelecer correlações entre
características físico-químicas dos filmes e suas propriedades mecânicas e tribológicas, bem
como correlações entre características físico-químicas da interface filme/substrato e a adesão
dos filmes ao substrato.
7
CAPÍTULO 2
2. Métodos experimentais
2.1. Preparação de amostras
A Figura 1 mostra um esquema da sequência da preparação das amostras para os
diversos estudos. Todas as amostras antes de serem tratadas foram polidas e limpas em banho
com acetona e ultrassom por 30 min. Para as amostras de aço AISI M2 e AISI H12 foram
utilizadas diversas granulometrias de lixas e na sequência polidas com pasta de diamante de 1
µm. Uma breve descrição das técnicas de preparação de amostras foi descrita na introdução.
Figura 1 – Etapas para a preparação das amostras utilizadas neste trabalho.
2.2. Método de deposição
2.2.1. Pulverização catódica (sputtering)
Esse processo de deposição de filmes finos foi descrito brevemente na introdução, mas
devido a grande importância e utilização no presente trabalho será aprofundado nesta seção
para um melhor entendimento do princípio físico-químico da técnica. A técnica de sputtering
é largamente empregada devido a obtenção de algumas vantagens frente a outros processos de
PVD, tais como:
8
• Alta pureza e densidade;
• Composição e estequiometria controladas;
• Baixa densidade de defeitos;
• Grande quantidade de materiais e compostos podem ser depositados;
• Uniformidade em espessura e reprodutibilidade;
• Baixa contaminação por partículas.
Durante o processo, inúmeros efeitos acontecem, os quais podem ocorrer com maior ou
menor probabilidade dependendo dos parâmetros escolhidos para a deposição. Alguns desses
efeitos são ilustrados na Figura 2 e o que se busca desse processo é a remoção de átomo do
alvo (sputtering), que representa apenas um dos efeitos que ocorrem.
Figura 2 – Efeitos de partículas energéticas em superfícies.
O sputtering de materiais é fortemente afetado pela energia da partícula incidente, o
qual é ilustrado em detalhe na Figura 3.
9
Figura 3 – Sputtering em três energias diferentes. (a) baixa, (b) e (c) alta energia.
Na Figura 3a é mostrado um átomo do material, representado pelos círculos abertos, que
é arrancado pela colisão de uma partícula pouco energética. Nesse caso a energia que a
partícula possui pode provocar somente um evento (remoção de um átomo). Já na Figura 3b e
c a energia é suficiente para gerar uma cascata de colisões e nota-se a movimentação dos
átomos em diferentes direções.
Além da energia dos íons incidentes, outros parâmetros são importantes para que o
fenômeno ocorra, tais como, massa do projétil, ângulo de incidência, massa do alvo e textura
do alvo. A maioria destes parâmetros são projetados pelos fabricantes de fontes de sputtering.
Uma grandeza usualmente utilizada para essa técnica é o rendimento (Y ou S) do processo,
que é definido por:
úáúá
Essa grandeza é influenciada por diversos parâmetros e na Figura 4 é mostrada a
influência do rendimento com a energia dos íons. A partir dessa figura conclui-se que o
rendimento é proporcional a energia dos íons até sua estabilização e consequentemente a
potência a qual o alvo é submetido. Para energias baixas (menores que 10 keV) a relação de Y
com a energia é praticamente linear, aumentando a energia não há variação significativa e
10
para altas energias o rendimento cai, devido a energia ser suficientemente alta para implantar
no alvo a partícula.
Figura 4 – Influência da energia no rendimento no processo de sputtering.
O rendimento para uma faixa de energias de 0,1 a 1 keV pode ser calculado pela
equação empírica:
5,2
! "/$ % &"/$'$/( )& % &*
+,,- ./"
Onde:
Usb = energia de ligação na superfície;
Zr = número atômico do alvo;
Zp = número atômico da partícula;
E = energia inicial da partícula incidente.
A partir da equação acima observa-se que o rendimento é máximo com projétil e alvo
de massa similar, devida a máxima transferência de energia em uma colisão elástica. Outros
fatores que influenciam no rendimento são a formação de liga ou compostos do projétil com o
alvo, diminuindo o rendimento e a possibilidade de canalização em alvos cristalinos.
11
2.3. Técnicas de análise
2.3.1. Espectrometria de retroespalhamento Rutherford (RBS)
A técnica consiste em incidir sobre a amostra um feixe monoenergético de íons de alta
energia, geralmente He+ com energia entre 1 e 3 MeV, e detectar a energia das partículas
retroespalhadas. A composição elementar do material analisado é obtida a partir do espectro
em energia das partículas retroespalhadas detectadas, bem como a quantidade de átomos
presentes [15,16,17], da qual pode ser extraída a espessura do filme, a partir do conhecimento
de sua densidade nominal. Na Figura 5 é mostrado um esquema do espectro de RBS de um
filme de composição genérica AB depositado em um substrato C, leve e de espessura infinita.
Figura 5 – Espectro de retroespalhamento Rutherford esquemático para um filme fino AB sobre um
substrato leve C.
Uma grandeza importante em RBS é o fator cinemático (K), utilizado na análise
elementar qualitativa. Esta grandeza depende da energia após o espalhamento (E) e da energia
inicial (E0):
/ +
12
A energia de partículas retroespalhadas a um dado ângulo depende de dois processos: a
perda de energia da partícula devido a transferência de momentum para o átomo alvo durante
o evento de retroespalhamento (descrito por K) e a perda de energia pela partícula durante a
passagem através da amostra sólida (ambos antes e depois do espalhamento). A Figura 6
mostra os eventos do retroespalhamento que ocorrem na superfície da amostra e em uma
profundidade d na amostra. Para o espalhamento na superfície da amostra a perda de energia
só é dada pela transferência de momento para o átomo do alvo.
A expressão do fator K em função dos diversos parâmetros envolvidos na colisão é:
/ 01.2 % !1"" 31.""2'./"1. %1" 4"
Onde:
M1 – Massa atômica da partícula incidente;
M2 – Massa atômica da partícula do alvo;
θ – Ângulo da trajetória da partícula antes e depois do espalhamento.
Figura 6 – Esquema de vários processos de perda de energia para retroespalhamento a partir da
superfície da amostra e ao longo da amostra. Energia é perdida por transferência de momento entre a partícula do feixe e da amostra e com a partícula incidente que atravessa o alvo antes e depois do
espalhamento.
13
A quantificação do espectro na RBS, embora possa ser feito de forma absoluta,
geralmente é realizada pela comparação das áreas dos picos de um padrão e da amostra que
está sendo medida. Usualmente, utiliza-se um padrão de bismuto (Bi) implantado em silício,
com uma quantidade conhecida de átomos de Bi. Com a quantidade de átomos por centímetro
quadrado e com a densidade do material que está sendo analisado, consegue-se estimar a
espessura do filme fino depositado [16]. A quantidade de átomos do material que se deseja
conhecer é dada, então pela equação:
56 578 ∙ :6;6 ∙;78:78 ∙
78"6"
Onde:
Q – Quantidade de átomos·cm-2 do elemento;
A – Área em baixo do sinal correspondente no espectro medido;
N – Número total de íons incidentes;
Z – Número atômico.
2.3.2. Espalhamento de íons com energia média (MEIS)
Esta técnica começou sendo desenvolvida como uma especialização da RBS,
desenvolvida pelo grupo FOM de Amsterdam. MEIS combina a técnica de RBS com uma
elevada resolução em energia, muito maior do que aquela usual em RBS. A resolução em
energia obtida pode ser de até 0,3 nm, enquanto em RBS dificilmente abrange resolução
menor que 10 nm. Este ganho na profundidade máxima é dado pela troca de detector em
relação a RBS que nesta é um detector de estado sólido, já no MEIS é um analisador toroidal
eletrostático mostrado na Figura 7 [18].
14
Figura 7 – Analisador da técnica de MEIS
A instrumentação é semelhante a técnica de RBS, sendo necessário um acelerador de
íon, uma câmara de ultra-alto vácuo (UHV) com goniômetro e um analisador eletrostático de
energia com detector sensível à posição como o descrito anteriormente. Esta técnica permite a
caracterização quantitativa com alta resolução em profundidade [19]. Na técnica em questão,
um feixe monoenergético de íons tipicamente de H+ com uma energia na ordem de 100 keV é
incidido na amostra e as partículas espalhadas são detectadas e analisadas. Esse espectro em
energia detectado também contém informações sobre a profundidade dos átomos do alvo,
pelo fato de que um íon incidente perde energia pelas colisões inelásticas com os elétrons do
alvo, tanto na entrada do mesmo quanto na saída das colisões. Devido a esta elevada
resolução em energia em relação a outras técnicas é possível detectar diferença isotópica dos
elementos [20].
A Figura 8 mostra um espectro característico de MEIS, de um filme de SiO2 com 5 nm
de espessura, sobre Si. No qual pode ser visto os elementos químicos separados, bem como os
isótopos de alguns elementos. A análise dos elementos químicos presentes nesta técnica é de
forma análoga a técnica de [21].
Analisador eletrostático de energia com detector sensível à posição
15
Figura 8 – Espectro equemático de MEIS.
2.3.3. Espalhamento de íons com energia baixa (LEIS)
A técnica de LEIS, assim como RBS e MEIS, é dada pela incidência de íons na amostra
e então medida a energia destes retroespalhados. Nesta técnica são, geralmente, utilizados
íons de He a uma energia entre 500 eV e 10 keV [22], na qual interagem com a matéria da
amostra e a energia final destes íons retroespalhados é detectada e medida por um analisador
eletrostático hemisférico, mostrado na Figura 9. Nesta técnica somente a primeira camada
atômica é analisada, pois íons aí espalhados não sofrerem neutralização, enquanto os íons que
chegam na segunda monocamada e suas posteriores são neutralizadas e, portanto, não são
analisadas em energia.
16
Figura 9 – Geometria de análise de LEIS e do analisador eletrostático de energia.
Este analisador eletrostático utilizado seleciona os íons que não neutralizaram e são
analisados em energia e detectados, assim contribuindo para o espectro. Esse é um dos
principais motivos pelo qual os picos do espectro são separados, diferenciando do RBS no
qual os picos formam patamares e se sobrepõem devido aos elementos químicos estarem
distribuídos em profundidade na amostra. Na Figura 10 mostra gráficos esquemáticos de
LEIS e RBS comparando ambas as técnicas.
17
Figura 10 – Espectros de He retroespalhado para as técnicas de LEIS e RBS para uma amostra de Si com Ag, Si e O na superfície.
2.3.4. Perfilometria de concentração utilizando reação nuclear ressonante estreita
(NRP)
Esta técnica permite determinar quantitativamente o perfil de concentração de
elementos leves, ou seja, a determinação da concentração em função da profundidade. A
diferença em relação a outras técnicas, por exemplo, RBS e MEIS, é a seletividade em
elementos atômicos. Para determinar o perfil de concentração de elementos leves com
nitrogênio, oxigênio, alumínio e silício em amostras são utilizados parâmetros de análise
específicos para a detecção de um isótopo do elemento desejado [23].
Um feixe de íons, geralmente H+, com energia de algumas centenas de keV até alguns
MeV é produzido em um acelerador e bombardeia a amostra. Reações nucleares com núcleos
de baixo número atômico são induzidas por este feixe. Os produtos destas reações,
tipicamente prótons, deutério, partículas α e raios γ, são detectadas, produzindo um espectro
de contagens de partículas versus energia [15]. Um exemplo das reações é:
18
; % → =." % > % ?.@
Como o objetivo desta análise é a determinação do perfil de concentração de elementos
leves, um feixe de prótons com energia de incidência correspondente a uma ressonância
estreita, intensa e isolada da curva de seção de choque da reação nuclear (Figura 11) é
utilizado. Na Figura 11 é mostrada a vantagem da utilização da energia de ressonância para a
reação 18O(p,α0)15N em 151 keV. Utiliza-se esta energia por: i) ser isolada, ou seja, não há
ressonância perto desta região, ii) intensa, possui uma seção de choque diferencial, ao redor
de 5 ordens de grandeza maior do que próxima à ressonância, iii) ter uma largura a meia
altura menor possível, que determina a sua resolução em profundidade.
Figura 11 – Seção de choque diferencial em função da energia de incidência dos prótons.
Para a obtenção do perfil de concentração, a incidência do feixe de íons na energia de
ressonância fará com que reações nucleares aconteçam, e a probabilidade destas reações
ocorrerem é significativa somente na superfície da amostra, pelo fato de perderem energia
pelas interações com o material. Então esse resultado das reações é detectado e com isso
gerado um espectro, mostrado na Figura 12a. A seguir a energia do feixe é aumentada para
19
que a reação ocorra não mais na superfície e sim ao longo da amostra que será detectada
gerando novamente um espectro, mostrado na Figura 12b. O alargamento do pico é devido ao
aumento na dispersão dos íons conforme eles entram no alvo [24].
(a) (b) (c)
Figura 12 – Detecção das reações nucleares (a) na superfície do material, (b) ao longo da amostra e (c) na profundidade da amostra.
Em ambos os espectros citados (Figura 12 (a) e (b)) é calculada a área abaixo da curva
que é proporcional à quantidade total de átomos presentes na fatia analisada. Fazendo esse
processo de passo em passo pode-se mapear a distribuição do elemento em função da
profundidade da amostra conforme mostrado na Figura 12 (c).
2.3.5. Espectroscopia de fotoelétrons induzidos por raios X (XPS)
XPS é uma técnica de fotoemissão, largamente utilizada para examinar o estado
químico de espécies próximas a superfícies sólidas e a distribuição de composição química
em função da profundidade [25]. Esta técnica envolve a ionização dos átomos pelo efeito
fotoelétrico, que é a emissão de elétrons por um material, quando exposto a uma radiação
eletromagnética. Ele pode ser observado quando a luz incide numa placa de metal, arrancando
elétrons dessa placa [26].
20
O mecanismo de emissão consiste em:
1°) absorção de raios X e promoção de um elétron do seu estado fundamental até o
estado final acima do nível de Fermi;
2°) transporte do elétron para a superfície;
3°) escape do elétron para a câmara de vácuo, com energia cinética dada pela equação:
A ℎC 3 3D
ou
ℎC 3 A 3D
Onde:
Eb – energia de ligação do elétron no sólido;
hυ – energia do fóton incidente;
Ek – energia cinética do elétron
W – função trabalho do espectrômetro.
A determinação da energia de ligação traz informação sobre o estado químico do
elemento. Na Tabela I é mostrada a variação da energia de ligação para as diferentes ligações
químicas do elemento Ti.
Tabela I – Energia de ligação para diferentes ligações do Ti
Ligação Energia de ligação (eV) TiO2 458,6 TiO 455,1 Ti-Ti 454,0 TiN 455,2
Na Figura 13 pode ser visto um esquema da técnica de XPS.
21
Figura 13 – Técnica de XPS: (a) irradiação da amostra pelo feixe e (b) fóton arrancando elétron do nível interno.
Após o elétron ser ejetado da superfície do material, ele chega ao analisador e são
contados quantos elétrons, com a mesma energia, estão sendo medidos. Então o gráfico de
contagens versus energia é obtido [27]. O analisador utilizado nesta técnica é o hemisférico
que consiste em duas cascas hemisféricas concêntricas. Aplicando uma diferença de potencial
entre elas permite-se a passagem de fotoelétrons com determinada energia os quais serão
detectados no final da calota.
Figura 14 – Espectro de Ti em diferentes estados.
22
Na Figura 14 é mostrado um espectro típico de XPS para o Ti, na qual pode ser visto os
dois picos característicos (2p3/2 e 2p1/2) deste elemento, devidos às interações spin-órbita. O
deslocamento dos picos do espectro nessa figura é devido ao estado oxidado do Ti, ou seja, na
parte de cima há Ti metálico e na parte de baixo o Ti está oxidado. Portanto há um
deslocamento dos picos no espectro por causa da diferença na energia de ligação dos dois
diferentes estados químicos presentes.
2.3.6. Difração de raios X (XRD)
Esta técnica é utilizada em larga escala em ciência dos materiais, pela sua grande
versatilidade e precisão. Com ela pode-se identificar as fases cristalinas presentes nos
materiais, bem como medir diversas propriedades estruturais, como tamanho de grão, tensões,
entre outras [28].
A Figura 15 mostra o esquema dos itens que compõem um difratômetro, onde pode ser
visto o feixe de raios X incidindo na amostra, o feixe difratado com ângulo de 2θ que é
detectado.
Figura 15 – Itens que compões um equipamento de difração de raios X.
23
A técnica de XRD para materiais cristalinos é baseada na difração de raios X, que são
radiações eletromagnéticas com comprimento de onda da ordem de 1 Å. Devido ao seu
campo elétrico associado, há interação com partículas carregadas, por exemplo, elétrons em
um sólido. Essa interação faz com que os elétrons emitam radiação e quando essas radiações
interagem uma com a outra de forma construtiva, ocorre difração. Para que ocorra interação
construtiva dois critérios devem ser satisfeitos: i) satisfazer a lei de Bragg e ii)
posicionamento dos átomos na célula unitária permitir que ocorra interferência construtiva
[29].
Para a identificação do composto analisado há padrões de espectros que são comparados
com a amostra analisada. Listas extensas de padrões são encontradas para determinado fim
[30].
Uma variação dessa técnica é a difração de raios X de baixo ângulo (GAXRD), que
consiste em utilizar um baixo ângulo de incidência dos raios X na amostra. A finalidade é
minimizar a contribuição do substrato no difratograma. Em muitos casos, nenhum pico do
substrato é medido, devido à baixa penetração do feixe de raios X na amostra, com isso há
somente difração no filme fino.
2.3.7. Reflectometria de raios X (XRR)
É uma técnica não destrutiva que fornece informações sobre espessura, homogeneidade,
rugosidade e densidade de filmes finos com monocamada ou multicamadas em substratos
planos. Esta técnica pode ser aplicada para o estudo de superfícies e interfaces de filmes finos
em resolução atômica, sem ser necessário utilizar materiais cristalinos [31]. A configuração
experimental para uma análise típica de XRR está mostrada na Figura 16. A curva de
refletividade obtida consiste num gráfico que relaciona a intensidade dos raios X refletidos
24
com o ângulo de incidência (θ). A medida de reflectometria consiste em variar esse ângulo de
um valor próximo de zero até alguns graus. Para ângulos entre zero e o valor do ângulo crítico
de reflexão externa total (θc), reflexão total irá ocorrer, como mostra a parte superior da
Figura 16. Acima de θc, a onda penetra no material, mostrado na parte inferior da Figura 16.
O valor de θc para um dado material depende de sua densidade eletrônica e da radiação
incidente. A profundidade até a qual a radiação irá penetrar aumenta rapidamente com o
ângulo, ocorrendo um aumento na absorção e, consequentemente, uma diminuição da
intensidade da radiação refletida. O resultado é um declive na curva de refletividade. O
ângulo crítico é medido como o ponto inicial dessa rápida queda na intensidade.
Figura 16 – Esquema da técnica de XRR.
Um espectro típico de uma análise de XRR é mostrado na Figura 17, onde são vistos a
interferência dos raios X refletidos para diferentes interfaces, camadas e multicamadas em
substratos planos. Podem ocorrer oscilações (franjas de Kiessig) ou efeitos de difração na
intensidade de raios X que depende do ângulo de incidência. A amplitude das franjas depende
da rugosidade da superfície e interface e da densidade eletrônica relativa dos materiais [31].
25
Figura 17 – Espectro típico de XRR.
2.3.8. Nanoindentação
A técnica de nanoindentação é utilizada para determinar propriedades mecânicas de
superfícies e filmes finos. Podem-se obter, também, perfis de dureza em profundidade,
preparando as amostras para análise em seção transversal. Sua característica fundamental é a
possibilidade de estudar as primeiras camadas atômicas, sendo que podem ser realizadas
medidas que atinjam de 10 até 1800 nm de profundidade [32].
Nos sistemas de nanoindentação, as medidas de dureza ocorrem de forma análoga às
dos testes mecânicos tradicionais (microdureza) onde as propriedades são obtidas de medidas
simples de carga mecânica, deslocamento e tempo. Um penetrador, geralmente com ponta de
diamante, é impulsionado em direção à superfície da amostra, enquanto a carga aplicada e o
deslocamento do penetrador são medidos. Na figura 18 é mostrado um esquema do
dispositivo de análise.
2θ (graus)
Inte
nsid
ade
(cps
)
26
Figura 18 – Esquema da ponta de penetração em um equipamento de nanoindentação.
Os resultados da carga como uma função do deslocamento nos materiais são muito
similares, e contêm, aproximadamente, as mesmas informações que são obtidas utilizando um
27
teste de compressão convencional. Nos testes convencionais, a área de contato permanece
constante durante todo o ensaio. Já com o indentador, a área se modifica com a penetração
[32]. Na Figura 19 é mostrado como o gráfico de carga e descarga varia com a profundidade.
Figura 19 – Representação de carga e descarga do penetrador em função da profundidade.
O principal objetivo de medidas de nanoindentação é a determinação das propriedades
de deformação plástica dos materiais, principalmente da dureza (H) e do módulo de
elasticidade (E) de filmes finos ou de camadas superficiais de sólidos. Em uma medida de
nanodureza, uma força (carga) P é aplicada a um indentador (uma ponta de diamante com
uma determinada forma) em contato com a superfície da amostra. Geralmente isto é feito em
três etapas. Inicialmente, a carga é aplicada com uma taxa pré-determinada até atingir um
valor máximo Pmax. Feito isto, a força é mantida constante por um determinado intervalo de
tempo, permitindo assim a acomodação do material. Em uma última etapa, a carga sob
controle é retirada ficando impressa sua marca na amostra (impressão residual).
28
2.3.9. Pino no disco
Pino no disco é um dos vários tipos de ensaio de desgaste, onde duas espécies são
requeridas. O primeiro consiste em um pino de raio conhecido que é posicionado
perpendicularmente em relação a um disco. Uma esfera rígida de aço ou de um material
cerâmico como a alumina ou carbeto de silício, frequentemente utilizados como pinos.
Usualmente, este pino se mantém estático enquanto a disco gira de forma rotacional. O plano
do disco pode ser orientado de forma horizontal ou vertical. A Figura 20a mostra a
representação esquemática do ensaio de pino no disco e na Figura 20b uma foto do
equipamento utilizado para ensaios deste tipo.
Figura 20 – (a) representação esquemática de ensaio pino no disco e (b) equipamento de pino-no-disco.
O pino é pressionado contra o disco através de um carregamento específico por meio de
um braço ou por uma alavanca presa por um peso. Outros carregamentos também são usados
como hidráulicos e pneumáticos. Os dados dos testes de desgaste pela perda de volume do
disco e do pino são computados separadamente. A quantidade de desgaste é determinada
através de técnicas metrológicas. Em alguns casos o teste de desgaste é medido através do
volume desgastado pela distância de escorregamento.
(a) (b)
29
A quantidade desgastada depende de muitos fatores como a força do carregamento
aplicada, as características da máquina, a velocidade de deslizamento e as propriedades do
material. Os testes de pino no disco não reproduzem todas as condições que podem ser
experimentadas. Não há certeza que a taxa de desgaste se comportará de maneira pré-
determinada sobre diferentes condições [33].
2.3.10. Coeficiente de atrito
O atrito pode ser definido como a força que se opõe ao movimento relativo entre duas
superfícies. Genericamente, a magnitude da força de atrito é descrita em termos de um
coeficiente de atrito, que é a razão entre a força de atrito e a força normal que pressiona os
corpos entre si. O coeficiente de atrito com essa descrição foi proposto originalmente por
Leonardo da Vinci, por volta de 1500 [34]. Na tecnologia moderna, o coeficiente de atrito é
considerado como sendo variável e dependente de parâmetros operacionais (umidade,
temperatura, velocidade e pressão de contato), de lubrificantes, de propriedades do substrato e
dos filmes superficiais [35]. A dependência em geral é maior com as propriedades das
superfícies e com o acabamento superficial, do que com as propriedades do substrato; porém,
as propriedades do substrato influenciam tanto na cinética de adsorção das espécies químicas,
como no acabamento originado do processamento deste [35].
Em termos de valores do coeficiente de atrito, a característica do atrito, por não ser uma
propriedade intrínseca de um material e nem de uma combinação de materiais, traz
complexidade no uso de valores tabelados como fonte de dados para projeto [36]. Os valores
na maioria das vezes são obtidos com algumas combinações de materiais e em condições
estabelecidas com sistemas laboratoriais que empregam geometrias simples. Obviamente, as
30
informações tabeladas fornecem orientações apenas e uma análise mais criteriosa deve ser
efetuada nos casos mais críticos.
É possível verificar que o atrito é sensível aos mesmos parâmetros e aos mesmos tipos
gerais de fenômenos envolvidos no desgaste, ou seja, aqueles relacionados com as
modificações das tribossuperfícies. E como resultado dessa dependência comum, alterações
nas tribossuperfícies que resultam em mudanças no desgaste frequentemente produzem
modificações também no atrito, e vice-versa. O monitoramento do atrito durante ensaios de
desgaste podem auxiliar na identificação dos fenômenos de transição do desgaste, embora se
ressalte que as tendências observadas no desgaste não são necessariamente as mesmas do
atrito [37]. O atrito está relacionado à energia total dissipada pelo sistema, sendo essa energia
constituída de duas partes: energia na forma de calor e energia na forma de desgaste [37]. A
energia na forma de desgaste é normalmente pequena em comparação à energia na forma de
calor. A razão entre essas duas energias pode variar para diferentes tribossistemas e diferentes
mecanismos de desgaste.
Se duas superfícies em contato apresentarem tendência a se mover uma em relação à
outra, surge uma força ''resistente'': a força de atrito. No caso de a forca aplicada não ser
suficiente para colocar o corpo em movimento, a força de atrito se opõe a força aplicada e é
chamada força de atrito estático. Esta não possui um valor único e pode variar entre zero a um
certo valor máximo, chamado força de atrito estático máximo (fe máx). Com boa aproximação,
este valor e independente da área de contato e é proporcional a força normal que a superfície
exerce sobre o corpo. A constante de proporcionalidade é o ''coeficiente de atrito estático''
(µe). Assim, podemos escrever:
EFGáH = IF ∙ JK
31
No caso de ocorrer movimento, aparece a chamada força de atrito cinético (fc) entre as
superfícies, que tem sentido contrário ao do movimento. A teoria prevê que ela seja constante,
independente da área de contato e proporcional à força normal exercida por uma das
superfícies sobre a outra. Esta proporcionalidade é expressa através do chamado ''coeficiente
de atrito cinético'' (µc):
EL IL ∙ JK
As constantes de atrito estático e cinético podem dizer muito sobre as características das
superfícies em contato. É interessante destacar que o coeficiente de atrito estático máximo é
sempre maior que o coeficiente de atrito cinético [38].
32
CAPÍTULO 3
3. Carbeto de vanádio
Dentre os muitos revestimentos protetores existentes, alguns já mencionados na
introdução, este capítulo estuda em particular o carbeto de vanádio (VC), que é candidato a
ser utilizado na indústria metal-mecânica como revestimento para discos de corte, fresas,
matrizes, entre outras ferramentas. As principais características que justificam a utilização
para esse fim são elevada dureza, resistência ao desgaste e resistência à corrosão. Outra
característica importante deste carbeto é a estrutura cristalina. A estrutura é do tipo cúbica de
face centrada (fcc), como pode ser observado na Figura 21.
Figura 21 – Estrutura cristalina de VC.
Na Figura 22 é mostrado o diagrama de fases para o sistema V-C [39].
33
Figura 22 – Diagrama de fases do sistema V-C.
O primeiro estudo realizado foi com amostras de VC, variando a pressão parcial do gás
reativo, neste caso metano (CH4), e a temperatura do substrato durante a deposição e
determinando a estrutura cristalina e estequiometria desses filmes finos. O substrato utilizado
foi silício monocristalino e a deposição foi pela técnica de magnetron sputtering reativo.
Os resultados obtidos pela combinação de RBS com reação nuclear ressonante
12C(α,α)12C são descritos nas Figuras 3 e 4 do Anexo 1, nas Figuras 1,2,3,4 e 5 do Anexo 2 e
na Figura 1 do Anexo 3. As análises de RBS foram realizadas com íons de He+ com energia
de 2 MeV e o detector com ângulo de retroespalhamento de 165°. Análises de reação nuclear
ressonante foram realizadas com energia de 4,26 MeV. Embora as condições de deposição
sejam diferentes entre algumas das amostras destas figuras, estes resultados mostram que é
possível depositar filmes estequiométricos ([C]/[V]=1 ou, simplesmente C/V = 1) a pressões
34
bem baixas de metano e que, em geral, a razão C/V diminui com o aumento da temperatura
do substrato. Os parâmetros de deposição para filmes estequiométricos são pressão parcial de
argônio 3x10-3 mbar, pressão parcial de metano 0,5 x 10-3 mbar e temperatura do substrato
400 °C. Além disto, os perfis de C indicam filmes homogêneos em profundidade. As taxas de
deposição parecem depender somente da potência transferida ao alvo de sputtering.
Quanto à estrutura cristalina dos filmes depositados, os resultados são mostrados nas
Figuras 1, 2, 5 e 6 do Anexo 1, na Figura 7 do Anexo 2 e na Figura 8 do Anexo 3. As análises
de difração de raios foram realizadas utilizando radiação Cu Kα (λ = 1.5418 Å), tensão de 40
kV e corrente de 30 mA. Estes resultados mostram uma estrutura cúbica de face-centrada,
com a predominância dos planos (111) e (200), os quais interceptam sítios de C intersticiais
tetraedrais e octaedrais, respectivamente. Ora, a intensidade dos picos correspondentes deve
crescer com o aumento da densidade de átomos de C em cada um destes planos. Nesse estudo
é proposto um mecanismo de difusão intersticial dos átomos de carbono na estrutura cristalina
fcc de filmes finos de VC, bem como a dependência com a temperatura do substrato durante a
deposição na ocupação dos sítios intersticiais octraédricos e tetraédricos dos átomos de
carbono.
No presente caso, átomos de C podem ocupar sítios tetraedrais ou octaedrais. A Figura
5 do Anexo 1 mostra que a razão de intensidades I111/I200 diminui com o aumento da
temperatura do substrato durante a deposição (ou temperatura de deposição). Esta razão de
intensidades foi simulada [40], com resultados mostrados na Tabela 1 do Anexo 1. O
decréscimo de I111/I200 com o aumento da temperatura, indica que átomos de C em sítios
tetraédricos metaestáveis na estrutura fcc migram para sítios octaédricos mais estáveis. A
Figura 6 do Anexo 1 mostra as duas possíveis situações cristalográficas do C. Finalmente, a
Figura 9 do Anexo 3, a qual foi obtida mediante rotação no plano da amostra, revela que
existe uma forte orientação preferencial nos filmes da VC depositados no presente trabalho.
35
As densidades reais dos filmes de VC do presente trabalho foram determinadas por
reflectometria de raios X, utilizando radiação Cu Kα com passo de 0,002°. A Figura 10 do
Anexo 2 e a Figura 4 do Anexo 3 revelam que as densidades para filmes depositados a 400 oC
e duas pressões diferentes de CH4, são de 6.4 e 5.6 g.cm-3, que são valores limites aqui
adotados para esta temperatura de deposição. A Figura 4 do Anexo 3 mostra ainda que a
densidade real dos filmes cai substancialmente para temperaturas de deposição menores.
A composição química dos filmes nos primeiros 10 nm abaixo da superfície foi
investigada usando XPS nas regiões de fotoelétrons 2p do vanádio e 1s do carbono. As
análises foram realizadas com uma fonte de raios X de MgKα (1256.3 eV), a resolução em
energia do espectrômetro é 0,9 eV. A região de fotoelétrons 2p do V mostra a existência de
ligações V-C e V-O, enquanto a região dos fotoelétrons 1s do C mostram ligações C-V, e
diferentes ligações C-C. Os espectros de fotoelétrons são mostrados na Figura 9 do Anexo 2.
A dureza, o coeficiente de atrito e a resistência ao desgaste é outra característica
relevante de revestimentos protetores, visto que as ferramentas de corte sofrem,
principalmente, desgaste abrasivo na sua utilização durante os processos de usinagem. Uma
das maneiras de avaliar o desgaste é o uso de análises tribológicas como pino no disco, na
qual a amostra (disco) gira enquanto o pino, um material com dureza elevada, é pressionado
com uma força constante sobre o disco. Após a análise há a formação de uma trilha no disco,
pelo desgaste do pino, com isso é avaliado o quanto o material é desgastado. Há também um
método de avaliar o desgaste de filmes finos pela razão entre duas propriedades mecânicas, a
dureza e o módulo de elasticidade, na forma H3/E2, conhecido como módulo de deformação
até ruptura. Para tanto essas duas propriedades podem ser medidas por nanoindentação. Essa
razão avalia a resistência à deformação plástica do filme fino, o que dá um indicativo do
desgaste. Com esse método é mais fácil obter comparativos entre amostras diferentes, visto
que os parâmetros de nanoindentação são mais constantes que o método exposto acima.
36
Na sequência do estudo, as propriedades mecânicas e tribológicas de filmes de VC
sobre silício monocristalino depositados pela técnica de magnetron sputtering reativo. O tipo
de substrato não tem uma influência significativa sobre a dureza e módulo de Young, pois
tratam-se de medidas de nano-dureza, nas quais a profundidade de inspeção é somente da
ordem de 20% da espessura do filme. Para os ensaios de desgaste do tipo pino-no-disco, foi
usado um substrato de aço AISI H12. Nesse estudo foram estabelecidas correlações entre os
parâmetros de deposição, tais como pressão parcial do gás reativo e temperatura do substrato
durante a deposição, e as características mecânicas e tribológicas dos filmes finos de VC. Os
resultados estão mostrados na Figura 11 do Anexo 2 e na Figura 7 do Anexo 3. Foi utilizado
um indentador do tipo Berkovich, com taxa de carga de 0,04 mN.s-1 e profundidade máxima
da indentação de 40 nm. Para filmes de VC estequiométricos com C/V=1, a dureza, o módulo
de Young e o módulo de deformação elástica até ruptura, H3/E2, aumentam com o aumento de
temperatura. Por outro lado, para uma determinada temperatura de deposição, a razão H3/E2
cresce até uma razão C/V de 1.2 e decresce para valores maiores desta razão.
Os valores da razão H3/E2 aqui determinados são considerados altos pela literatura,
fazendo com que filmes de VC sejam fortes candidatos a revestimentos protetores, pois
possuem uma significativa resistência ao desgaste. Ensaios de desgaste do tipo pino-no-disco
também foram realizados aqui, mostrando que filmes com espessura em torno de 1 µm não
sofrem desgaste abrasivo significativo. Um resultado típico de ensaio de desgaste é mostrado
na Figura 23. Nota-se que para filmes suficientemente espessos, situação em que a resistência
ao desgaste do filme predomina, o desgaste volumétrico é muito pequeno, talvez mesmo
inexistente. A analise de desgaste foi realizada com um pino de alumina (Al2O3), carga 20 N e
60 rpm de rotação.
37
Figura 23 – Volume de desgaste versus tempo de deposição.
3.1. Corrosão
Estudos de corrosão dos revestimentos protetores são, em geral, insatisfatórios. Quando
expostos a um meio corrosivo, observa-se corrosão galvânica local do substrato, uma vez que
eletrólito pode atingir o substrato de aço por transporte através de poros e microfissuras. Um
par galvânico é formado, o revestimento composto sendo em geral o eletrodo mais nobre.
Como consequência o substrato de aço deverá dissolver anodicamente. Além disto, os filmes
depositados por PVD possuem uma microestrutura colunar e problemas de corrosão em
aplicações são atribuídos a vazios nestas colunas, a pinholes, e fissuras eventualmente
existentes. Investigamos aqui as propriedades de corrosão de aços revestidos com filmes de
VC, o que não existe na literatura. O aço escolhido para substrato é o AISI H12, o qual já
tinha sido utilizado em ensaios pino-no-disco.
As medidas eletroquímicas, incluindo impedância, foram realizadas com um
equipamento Voltalab 10, modelo PGZ 100 Radiometro Copenhagen
potenciostato/galvanostato. O meio corrosivo foi uma solução aerada 3.5% de NaCl. Uma
célula de vidro com parede dupla foi utilizada para realizar os ensaios de corrosão. O eletrodo
38
de trabalho foi um disco de aço AISI H12 montado sobre num tubo de vidro com epoxy
Araldite.
A corrosão pode ser definida como a deterioração de um material, geralmente metálico,
que se dá na sua superfície por ação química ou eletroquímica do meio ambiente, com ou sem
esforço mecânico [41]. A deterioração causada pela interação físico-química entre o material
e seu meio operacional representa alterações prejudiciais indesejáveis, sofridas pelo material,
tais como desgaste, variações de composição química ou modificações estruturais, tornando-o
inadequado para o uso. Sendo a corrosão, em geral, um processo espontâneo, está
constantemente transformando os materiais metálicos de modo que a durabilidade e
desempenho dos mesmos deixam de satisfazer os fins a que se destinam. Uma das formas de
corrosão mais comuns é a chamada puntiforme ou por pite, que é a corrosão que se processa
em pontos ou em pequenas áreas localizadas na superfície produzindo pites, que são
cavidades que apresentam o fundo em forma angulosa e profundidade geralmente maior do
que seu diâmetro. Neste trabalho a corrosão de filmes de VC sobre aço foi estudada, com o
objetivo de otimizar os parâmetros de deposição, de maneira a tornar estes filmes resistentes
à corrosão. Não encontramos na literatura estudo de corrosão de filmes de VC sobre aço.
A seguir são descritos os dois métodos utilizados para avaliar a corrosão neste trabalho.
Esta descrição é feita aqui, em separado dos métodos experimentais, pois demanda uma
exposição mais ampla.
Na Figura 24a é mostrado um arranjo experimental típico de corrosão, e na Figura 24b
uma célula eletroquímica típica.
39
Figura 24 – (a) arranjo experimental e (b) célula eletroquímica típicos de ensaios de corrosão.
3.1.1. Polarização cíclica
O teste eletroquímico mais comum para a corrosão localizada é a voltametria de
polarização cíclica. Referindo-nos à Figura 24, este teste envolve a polarização anódica do
material a partir do potencial de circuito aberto até uma predeterminada densidade de corrente
(conhecido como vértice de densidade de corrente). Neste ponto o potencial decresce até a
corrente ser revertida [42,43], como mostrado na Figura 25.
A cinética de processos eletródicos é comumente estudada por polarização cíclica,
técnica esta que envolve o monitoramento da corrente quando o potencial do eletrodo de
trabalho é variado com o tempo. A Figura 25a ilustra o voltamograma cíclico, na qual o
potencial é variado linearmente entre E1 e E2 e em seguida entre E2 e E1. A taxa de variação
do potencial em relação ao tempo é conhecida como velocidade de varredura de potencial.
Um voltamograma cíclico fornece indicações sobre a reversibilidade das reações de
transferência de elétrons, precedidas ou seguidas por reações químicas, relativamente lentas e
dos efeitos de adsorção, mostrado na Figura 25b. Aplica-se um potencial a partir do potencial
de circuito aberto (Ecorr), aumentando no sentido positivo (anódico) até haver uma grande
variação na corrente. Quando o valor da densidade de corrente programado for atingido, é
(a) (b)
40
revertido o potencial, o qual passa a decrescer na direção negativa (catódica). O potencial
onde a densidade de corrente aumenta rapidamente é potencial de pite (Epit). Quando o pite
ocorre, há um laço de histerese na volta, e o potencial do laço quando ele fecha é o de
proteção ou repassivação (Epro). O potencial final deve ser o Epro, determinado por
experimentos preliminares. Se o potencial de pite e de proteção forem iguais, há uma pequena
tendência de formação de pites. Se o potencial de proteção for mais positivo (anódico) que o
potencial de pite, então não há tendência de formação de pites. Se o potencial de proteção for
mais negativo que o de pite, então pites ocorrem [44].
Figura 25 – (a) Variação do potencial com o tempo e (b) curva resultante da corrente por potencial em um
voltamograma cíclico típico.
3.1.2. Espectroscopia de impedância eletroquímica
A espectroscopia de impedância eletroquímica (Electrochemical Impedance
Spectroscopy – EIS) é uma técnica poderosa para a caracterização de uma grande variedade
de sistemas eletroquímicos e para a determinação da contribuição de processos individuais de
eletrodo ou eletrólito nestes sistemas. Pode ser usada para investigar a dinâmica de cargas
ligadas ou móveis nas regiões de volume ou de interface de qualquer tipo de material líquido
ou sólido [42].
(b) (a)
41
A impedância de um circuito elétrico representa o nível de dificuldade que uma corrente
elétrica alternada encontra para percorrer este circuito. Pode ser expressa em termos de
elementos de circuito elétrico: resistência, capacitância e indutância [45]. O princípio desta
técnica consiste em aplicar um sinal alternado de pequena amplitude (5 a 20 mV) a um
eletrodo inserido num eletrólito. Compara-se, então, a perturbação inicial (aplicada) com a
resposta do eletrodo, pela medida da mudança de fase dos componentes de corrente e
voltagem e pela medida de suas amplitudes. Isto pode ser feito nos domínios de tempo ou nos
domínios de frequência, utilizando-se um analisador de espectro ou um analisador de resposta
de frequência, respectivamente [46]. É importante salientar que a perturbação inicial é uma
perturbação de potencial (DE), do tipo senoidal, que deve ser imposta no estado estacionário
do sistema e a resposta do eletrodo é uma corrente (DI), também senoidal, porém com uma
diferença de fase f em relação ao sinal aplicado. Portanto, a impedância, que se representa por
Z, mede a relação entre DE e DI.
O conceito básico envolvido em EIS é que uma interface pode ser vista como uma
combinação de elementos de circuito elétricos passivos, i.e., resistência, capacitância e
indutância. Quando uma corrente alternada é aplicada a estes elementos, a corrente resultante
é obtida usando a lei de Ohm.
As principais vantagens desta técnica são: a) fornece informações sobre a cinética do
processo, pela determinação da velocidade de corrosão; b) técnica é precisa e reprodutiva,
apropriada para ambientes de alta resistividade como é o caso de cerâmicos, solo e concreto;
c) fornece dados a respeito do mecanismo de controle eletroquímico, indicando se o processo
corrosivo se dá por ativação, concentração ou difusão; d) caracteriza o estado do duto e a
morfologia da corrosão; e) a técnica é não-destrutiva e não perturbativa, uma vez que sinais
aplicados são de pequena amplitude, de forma que o potencial de corrosão não é alterado; f)
permite o acompanhamento da evolução do estado passivo ou ativo ao longo do tempo.
42
O conceito de resistência elétrica pode ser definido pela lei de Ohm, onde resistência é a
forma de um circuito resistir a um fluxo de corrente e pode ser matematicamente expresso
por:
R = V / I
Onde:
R – resistência (Ω); V – tensão (V); I – corrente (A).
Entretanto, esta relação é limitada a um circuito elementar, o resistor. No mundo real,
alguns sistemas complexos são forçados a abandonar o simples conceito de resistência [47].
Para isto, utiliza-se um conceito mais elaborado chamado de impedância (Z) cuja função é
medir a tendência de um sistema resistir, ou impedir o fluxo de corrente elétrica alternada
(AC). A expressão matemática equivalente pode ser descrita como:
Z = Vas / Iac
Na EIS, uma corrente alternada de frequência variável é aplicada a amostra, sendo a
frequência alta para reações rápidas e baixa para reações lentas. Isto permite que um espectro
de impedância acumule uma grande quantidade de informações eletroquímicas em um único
experimento.
A espectroscopia de impedância eletroquímica pode medir tanto a resistência de um
material, quanto sua capacitância em uma célula eletroquímica. A EIS permite também
monitorar simultaneamente a taxa de corrosão de um substrato metálico, quando este está
exposto ao eletrólito ou quando o eletrólito permeia por falhas no recobrimento.
3.1.3. Diagrama de Nyquist
O diagrama de Nyquist consiste de uma série de pontos, cada um representando a
grandeza e a direção do vetor de impedância para uma frequência particular. O diagrama é um
43
plano complexo de coordenadas cartesianas, onde se tem na abscissa a parte real (termos
resistivos) e na ordenada a parte imaginária (termos capacitivos ou indutivos). Os dados de
impedância representados no plano cartesiano sob uma larga variação, que gera configurações
típicas, de acordo com o mecanismo eletroquímico predominante [48]. A Figura 26 mostra
um diagrama de Nyquist típico.
Figura 26 – Diagrama de Nyquist, com o vetor de impedância para um sistema eletroquímico simples.
3.1.4. Soluções e condições de trabalho
O eletrodo de trabalho foi obtido de uma placa comercial do aço–ferramenta AISI H12
e moldado em um tubo de vidro preso com resina epóxi Araldite®, sem tratamento térmico.
NaCl de pureza analítica da Sigma® foi utilizado sem purificação prévia. Para o preparo das
soluções foi utilizada água filtrada, destilada e deionizada. Foi utilizada solução estoque de
NaCl 3,5% (m/V) para a realização dos ensaios de corrosão. Para todos os experimentos, 75
mL de solução estoque de NaCl 3,5% foram adicionados à célula. Todos os ensaios foram
realizados com a solução não desaerada e em temperatura ambiente.
3.1.5. Célula, eletrodos e corpos de prova
Os testes eletroquímicos foram realizados em uma célula para três eletrodos com parede
dupla de vidro. Como eletrodo de trabalho foi utilizado um disco de aço–ferramenta AISI
44
H12 revestido com carbeto de vanádio (VC) de dimensões de 8 x 8 cm. A limpeza da
superfície do eletrodo foi realizada antes de cada ensaio. Para os ensaios brancos (com placas
de aço AISI H12 sem revestimento de VC) o eletrodo de trabalho era polido até brilho
especular com uma lixa d’água de granulometria 1200, limpo em banho de ultrassom, lavado
com acetona, etanol e água destilada. Após a imersão do eletrodo de trabalho na célula
eletroquímica, foi aplicado um potencial de – 1200 mV (vs. ESCE) para limpar a superfície de
qualquer impureza ou produto de corrosão que tenha se formado no curto período de tempo
entre o polimento e a imersão do eletrodo na célula. O eletrodo auxiliar foi um bastão de
grafite, e o eletrodo de referência o eletrodo de calomelano saturado (SCE) conectado à célula
por uma ponte salina constituída de KCl saturado com capilar de Luggin-Habber. Todos os
potenciais mencionados no texto são medidos em relação ao potencial do SCE. Na Figura 27a
é mostra a célula utilizada e na Figura 27b os eletrodos utilizados.
Figura 27 – (a) Eletrodos utilizados e (b) célula eletroquímica para ensaios de corrosão.
3.1.6. Instrumentação
Os ensaios eletroquímicos, incluindo impedância, foram realizados em um potenciostato
Voltalab 10, modelo PGZ 100 da Radiometer Copenhagen, conectado a um microcomputador
usando o software VoltaMaster 4.0 para aquisição e análise dos dados. Para a preparação das
(a) (b)
Eletrodo de trabalho
Eletrodo auxiliar
Eletrodo de referência
Eletrodo de referência
Eletrodo auxiliar
Eletrodo de trabalho
45
soluções estoque de NaCl 3,5% uma massa adequada do sal foi pesada em uma balança
analítica Shimadzu Libror AEX 200G.
3.1.7. Procedimentos
As curvas de potencial de circuito aberto (PCA) versus tempo foram obtidas de acordo
com as normas ASTM G5 e curvas de polarização cíclica foram obtidas de acordo com a
norma ASTM G61, que é recomendada para a avaliação da tendência de materiais sofrerem
corrosão por pites em soluções contendo íons cloreto. O potencial de circuito aberto do
eletrodo de trabalho foi medido por 60 minutos antes da realização dos experimentos de
impedância eletroquímica e de polarização cíclica. A varredura de potenciais para os ensaios
de polarização começou sempre a partir de valores mais negativos em relação ao PCA medido
anteriormente, e seguiu na direção de potenciais positivos até atingir uma densidade de
corrente máxima de 1,5 mA.cm-2. Neste ponto, a variação potenciodinâmica foi invertida para
a direção negativa até atingir um valor de potencial de – 0,250 V em relação ao PCA.
O potencial de pite (Epit) foi obtido no ponto onde a densidade de corrente aumenta
acentuadamente durante a varredura de potenciais na direção positiva. E o potencial de
proteção (Epro) ou de repassivação foi obtido no ponto em que a curva de polarização se
fecha durante a varredura de potenciais na direção negativa.
Espectroscopia de impedância eletroquímica foi realizada em circuito aberto com uma
onda sinusoidal de 10 mV de amplitude, em frequências na faixa de 100 kHz a 5 mHz. Os
resultados de impedância foram representados pelos diagramas de Nyquist.
3.2. Corrosão de filmes de VC
Para avaliar a proteção contra corrosão foram realizadas duas análises, polarização
cíclica e espectroscopia de impedância eletroquímica (EIS). Com estas duas análises foi
46
possível determinar quais os melhores parâmetros de deposição de filmes de VC, por
magnetron sputtering reativo, que tornem estes filmes pouco suscetíveis à corrosão. Para
tanto, foram variados três diferentes parâmetros de deposição: a) pressão parcial de CH4,
levando a filmes de composição diferentes e b) temperatura do substrato durante a deposição.
No primeiro experimento a pressão parcial de metano foi variada desde filmes
subestequimétricos até superestequiométricos. Como pode ser visto na Figura 28 os filmes
com maior quantidade de carbono, no caso C/V = 2,5 (33% CH4), obtiveram um melhor
comportamento frente à corrosão. Na Figura 28a são mostradas as curvas obtidas pela análise
de EIS e como pode ser visto há uma maior resistência nas amostras com C/V = 2,5 (33% de
CH4), o que impede a passagem de elétrons e consequentemente o processo de corrosão
eletroquímica. Na Figura 28b mostra o resultado da análise de voltametria cíclica e como
pode ser visto a corrosão se dá por pite e quanto maior a composição de carbono maior a
proteção contra corrosão localizada. Esses resultados demonstram que a quantidade elevada
de carbono passiva o filme e dá melhor estabilidade eletroquímica. Com estes resultados os
filmes seguintes de VC foram depositados com C/V = 2,5 (33% CH4 e 67% Ar).
Figura 28 – (a) EIS e (b) voltametria cíclica de filmes finos de VC sobre aço, variando a composição do plasma.
47
No experimento seguinte foi variada a temperatura do substrato durante a deposição do
filme de VC. Na Figura 29 são mostrados os resultados das análises a diferentes temperaturas,
variando desde a ambiente até a 400 °C. Na Figura 29a pode ser visto que a temperatura de
400 °C há uma maior resistência a passagem de elétrons, comprovando uma melhor
resistência à corrosão. Na Figura 29b foi comprovado que a corrosão é localizada do tipo pite
e que a melhor resistência à corrosão se dá nas amostras com o substrato a 400 °C.
Figura 29 – (a) EIS e (b) voltametria cíclica de filmes finos de VC sobre aço, variando a temperatura do substrato durante a deposição.
Uma imagem típica de um pit de corrosão, obtida por microscopia eletrônica de
varredura, é mostrada aqui na Figura 30. O substrato no fundo do pit pode ser visto, expostos
ao meio corrosivo. A morfologia dos pits é do tipo aberta, como prevista pelos ensaios de
EIS. Quando expostos a um meio agressivo, os substratos de aço sofrem corrosão galvânica
local. Como os revestimentos protetores duros não são muito densos, o eletrólito pode atingir
o substrato de aço através de pores ou microfissuras. Um par galvânico é formado, o
revestimento sendo eletroquimicamente o mais nobre. Como consequência, o substrato de aço
começa a se dissolver anodicamente. Além disto, revestimentos depositados por técnicas de
PVD, como o sputtering, se caracterizam por possuir uma micro-estrutura colunar, sendo os
48
problemas de corrosão em aplicações geralmente atribuídos aos vazios entre estas colunas, ou
a pinholes ou aos eventualmente existentes microcraks.
Figura 30 – Microscopia eletrônica de varredura de filme fino de VC sobre aço AISI H12, após corrosão em solução de 3,5% de NaCl. As imagens mostram os pites (a) e detalhe dos pites expondo o substrato (b).
Análises complementares foram realizadas pelo método do espalhamento Raman. Os
resultados são apresentados na Figura 31. As análises foram realizadas a temperatura
ambiente (20 °C) com um laser de estado sólido (λ = 473 nm). Os espectros Raman podem ser
deconvoluidos em dois picos (ou bandas) gaussianos mais um background linear. O pico ao
redor de 1350 cm-1 é atribuído a uma banda de desordem (D), em quanto aquele ao redor de
1582 cm-1 é atribuído a grafite (G). A razão de intensidades ID/IG representa a densidade de
defeitos no filme contendo carbono, servindo usualmente para determinar a quantidade de
carbono amorfo. Como todos os filmes com C/V > 1tem a mesma razão ID/IG, podemos dizer
que eles têm a mesma quantidade de carbono amorfo. Por outro lado, filmes com C/V = 1 ou
menor, não apresentam nenhum indício de carbono amorfo.
49
Figura 31 – Espectro de espalhamento Raman para filmes de VC com diferentes composições à 20 °C.
O carbono amorfo acima da estequiometria existente nos filmes de VC consiste
principalmente de aglomerados aromáticos nanoscópicos, além de C em solução na matriz
cristalina. Assim sendo, a inibição da corrosão devido a trajetórias rápidas na estrutura
colunar dos revestimentos pode ser devida ao bloqueio pelos nano-aglomerados que ali se
inserem. Alternativamente, nanoclusters de carbono em solução sólida nos filmes VC podem
preencher os pinholes ali existentes ou atuar como barreira ao transporte de espécies
corrosivas.
3.3. Discussão dos resultados de corrosão
Os ensaios de corrosão aqui realizados mostram uma proteção que aumenta com a
concentração de carbono nos filmes e com a temperatura de deposição.
No caso da concentração de C nos filmes, isto pode ser atribuído ao bloqueio de
caminhos fáceis para migração de espécies corrosivas pelos nano-aglomerados de carbono
amorfo, entre eles vazios entre colunas, pinholes e micro-fissuras. Porém, como discutido
50
abaixo, o aumento da proteção com o aumento da concentração de C merece uma discussão
mais aprofundada.
Quanto à temperatura de deposição, a Figura 4 do Anexo 3 mostra que o aumento da
mesma de 20 para 400 oC leva a um aumento de 13% na densidade real dos filmes de CV,
aumento este muito significativo. Assim, um primeiro mecanismo de proteção é a formação
de mais e melhores barreiras ao transporte de espécies corrosivas pela simples compactação
dos filmes depositados a maiores temperaturas.
Outro causa possível para o aumento da proteção em temperaturas de deposição mais
altas está baseada no fato de, embora concentrações maiores de C, como C/V = 2.5,
aumentarem a resistência à corrosão, a quantidade de nanoclusters é aproximadamente a
mesma para todos C/V > 1. Assim, a maior resistência à corrosão dos filmes VC pode ser
devida a migração de C de sítios intersticiais tetraedrais para sítios intersticiais octaedrais em
temperaturas de deposição mais altas, resultando numa maior disponibilidade dos sítios
intersticiais tetraedrais, os quais são sítios mais reativos do C.
3.4. Conclusões Parciais
Os filmes de VC aqui estudados apresentaram propriedades mecânicas que encorajam
sua utilização ou, pelo menos, a continuação dos estudos aqui apresentados.
A dureza H e o módulo de Young E dos filmes aumentam com a razão C/V até a
unidade, ou seja, até a estequiometria, decrescendo para valores de C/V maiores. Um
comportamento bastante similar foi observado para o módulo de deformação até ruptura,
H3/E2, o qual atinge um máximo de 1 GPa, para C/V = 1.2 A dureza máxima dos filmes é de
26 GPa. Ensaios de desgaste do tipo pino-no-disco confirmam o valor muito baixo do
desgaste previsto pelo critério H3/E2.
51
O aumento da dureza dos filmes pode ser atribuído a diferentes causas. Inicialmente, a
compactação dos filmes pelo aumento na temperatura de deposição pode auxiliar no aumento
da dureza. Porém, isto só é verdade até certa concentração de C intersticial, no caso até 1.
Acima de C/V = 1, o excesso de C promove a formação de clusters de C que constituem
caminhos fáceis para penetração da ponta de indentação. Quanto à resistência ao desgaste, C
intersticial, bem como certa quantidade de clusters nanoscópicos de C, ainda que pequena,
constituem excelentes candidatos a lubrificantes sólidos. O papel do grafite como lubrificante
sólido é bem conhecido, mas o papel de nanoclusters de C não é bem conhecido e o presente
trabalho abre uma janela nesta direção. Não pode ser negligenciado aqui o papel de uma
estrutura intersticial octaedrica, mais estável, capaz de moderar o desgaste abrasivo.
A corrosão de aço AISI H12 revestido com filmes VC também foi fortemente reduzida.
Porém, diferentemente das propriedades mecânicas e tribológicas, a proteção máxima é obtida
para o maior valor de C/V aqui utilizado, ou seja, 2.5. Por outro lado, a proteção é máxima
para o maior valor da temperatura de deposição, ou seja, 450 oC.
Os ensaios de corrosão aqui realizados mostram uma proteção que aumenta com a
temperatura de deposição e com a concentração de carbono nos filmes.
Quanto à temperatura de deposição, um aumento de 13% na densidade real dos filmes
de CV, pode ser responsável por mais e melhores barreiras ao transporte de espécies
corrosivas pela simples compactação dos filmes depositados a maiores temperaturas.
Outro causa possível para o aumento da proteção em temperaturas de deposição mais
altas está baseada no fato de, embora concentrações maiores de C, como C/V = 2.5,
aumentarem a resistência à corrosão, a quantidade de nanoclusters é aproximadamente a
mesma para todos C/V > 1. Assim, a maior resistência à corrosão dos filmes VC pode ser
devida a migração de C de sítios intersticiais tetraedrais para sítios intersticiais octaedrais em
52
temperaturas de deposição mais altas, resultando numa maior disponibilidade dos sítios
intersticiais tetraedrais, os quais são sítios mais reativos do C.
Os resultados aqui apresentados indicam a possibilidade de otimizar revestimentos de
VC para melhorar concomitantemente a resistência à corrosão e ao desgaste do aço revestido.
Isto pode ser feito controlando a temperatura do substrato durante deposição e a composição
dos filmes ou, ainda, pelo uso de multicamadas ou filmes de composição que varia
gradualmente para atingir as propriedades desejadas. Pesquisas nesta direção estão atualmente
em andamento.
53
CAPÍTULO 4
4. Nitreto de silício
Existe atualmente um interesse crescente em materiais e revestimentos que possuam
apreciáveis dureza e tenacidade em altas temperaturas. Tal interesse está ligado
principalmente a ferramentas para usinagem, corte e perfuração a seco, assim como a moldes
para injeção de metais, além de outras aplicações [49,50]. A tecnologia para trabalho a seco é
importante econômica e ecologicamente, uma vez que o uso de lubrificantes líquidos envolve
altos custos e altos danos ao ambiente [51].
As desvantagens dos revestimentos baseados em Ti limitam severamente suas
aplicações em altas temperaturas. Isto coloca um desafio, uma vez que a maioria das
ferramentas para altas temperaturas envolvem formação de uma camada de óxido protetora
quando interage com o ambiente. Tal camada de óxido deve ser estável, densa, aderente, e de
crescimento lento, além de, obviamente, possuir alta dureza, alta resistência à corrosão e
oxidação e baixos coeficientes de atrito e desgaste em altas temperaturas. Estas condições não
são preenchidas por revestimentos a base de Ti acima de 800 oC [52], o que impede seu uso
em temperaturas tão altas quanto 1000 oC que são atingidas pela superfície da ferramenta
durante trabalho. Nestas temperaturas, o óxido de Ti se degrada, dando origem a formação de
camadas porosas e não protetoras.
A Figura 32 apresenta um gráfico da dureza do material em função da temperatura de
tratamento térmico em atmosfera de oxigênio, onde é observado que para os materiais
atualmente utilizados como revestimentos tais como, TiN, CrN, TiAlN e CrAlN, todos eles
quando submetidos a altas temperaturas, apresentam redução na dureza [49].
54
Figura 32 – Variação da dureza para os revestimentos TiN, CrN, TiAlN e CrAlN (indicados na legenda) depositados por PVD, após o tratamento térmico em diferentes temperaturas. Os pontos em 25 °C
referem-se a revestimentos sem tratamento térmico.
O nitreto de silício (Si3N4) é um candidato promissor como revestimento para uso em
temperaturas, mesmo acima de 1000 oC, porque ele conserva sua razoavelmente alta dureza,
sua estabilidade termodinâmica, resistência à corrosão e oxidação nas altas temperaturas
desejadas aqui. Assim, como a maioria dos revestimentos perdem dureza acima de uma certa
temperatura (ao redor de 800 oC), é importante verificar o comportamento de revestimentos
de Si3N4 nestas temperaturas e acima delas. Também a velocidade de crescimento e a
composição de óxidos ou oxinitretos em altas temperaturas merece ser avaliada [53,54,55]. Na
Figura 33 é mostrado o diagrama de fases para o sistema N-Si [56].
55
Figura 33 – Diagrama de fases para o sistema N-Si.
Os substratos de silício monocristalino (001) e carbono amorfo utilizados neste trabalho
foram previamente limpos em um banho de acetona P.A. durante 30 minutos em uma
lavadora ultrassônica. Após as amostras de Si foram limpas com uma solução 10% de ácido
fluorídrico.
As deposições dos filmes de nitreto de silício foram realizadas em pela técnica de
magnetron sputtering reativo, no qual foi utilizado um alvo de silício de alta pureza (>
99,99%) e nitrogênio como gás reativo. Foi utilizada uma fonte de rádio frequência (13,56
MHz). A densidade de potência no alvo foi de 7,7 W.cm-2.
A fim de investigar a estabilidade térmica e resistência à oxidação dos revestimentos de
Si3N4 depositados, as amostras foram colocadas em um forno de quartzo de pressão estática
56
resistivamente aquecido, o qual foi bombeado a uma pressão inferior a 2 x 10-7 mbar, antes de
ser pressurizado com oxigênio enriquecido a 97 % no isótopo de massa 18, posteriormente
denominado tratamento térmico em 18O2. O tratamento térmico foi realizado durante 1 hora
com pressão de 100 mbar de 18O2, em três diferentes temperaturas, ou seja, 250 °C, 500 °C e
1000 °C. A utilização do isótopo raro 18O nos permite distingui-lo do oxigênio anteriormente
incorporado nos filmes devido à contaminação ou devido à exposição ao ar atmosférico.
A composição elementar dos filmes foi avaliada por RBS, utilizando íons de He+ com
uma energia de 2 MeV e um ângulo de detecção de retroespalhamento de 165º. A estrutura
cristalina dos filmes foi determinada por XRD, utilizando um ângulo de incidência constante
de 1° e radiação de Cu Kα (λ = 1,5418 Å). As densidades dos filmes foram obtidas por XRR,
as medições utilizaram radiação de Cu Kα e um ângulo de incidência de 0,002°.
A dureza e módulo de elasticidade reduzido foram obtidos pela técnica de
nanoindentação com um penetrador Berkovich, com carga de 0,03 N.s-1 e uma profundidade
de indentação máxima de 20 nm. Os perfis de 18O e 15N foram determinados por NRP,
utilizando as ressonâncias estreitas (Γ = 100 eV e 120 eV) nas curvas de seção transversal das
reações nucleares do 18O(p,α)15N e 15N(p,α,γ)12C em 151 keV e 429 keV, respectivamente.
XPS foi realizada utilizando radiação Mg Kα (1253,6 eV) em um ângulo de 60º, a fim de
avaliar os ambientes químicos de Si e N.
4.1. Composição elementar e taxa de deposição
A composição elementar de filmes de Si3N4 depositados sobre substratos de carbono, em
função da pressão parcial de N2 no plasma ou em função da temperatura de deposição foram
determinados por RBS. A Figura 1 do Anexo 4 mostra os resultados, aonde vemos que filmes
estequiométricos são formados, na temperatura de deposição de 400 oC, para pressões parciais
57
de N2 no plasma maiores do que 1 × 10-3 mbar. Deposição a temperatura ambiente não leva a
filmes estequiométricos em nenhuma pressão parcial de N2 no plasma.
4.2. Cristalografia e densidade real
A cristalografia dos filmes foi determinada por GAXRD. Os resultados são mostrados
na Figura 2 do Anexo 4, para filmes depositados a 20, 200 e 500 oC. Vê-se que os filmes são
essencialmente amorfos, com exceção daqueles depositados a 500 oC aonde são observados
picos atribuídos a fase metaestável α-Si3N4.
A densidade real e a espessura dos filmes foram determinadas por XRR, conforme
mostrado na Figura 3 do Anexo 4. A espessura foi também determinada a partir dos
resultados de RBS, usando a densidade real. A densidade real é de 3.01 g.cm-3 e a taxa de
deposição da ordem de 1.6 nm.s-1. As densidades superficiais de Si e N são mostradas na
Figura 4 do Anexo 4, em função do tempo de deposição.
4.3. Propriedades mecânicas e tratamento térmico
A dureza, o módulo de Young e o módulo de deformação elástica até ruptura dos filmes
de Si3N4 (H3/E2) são mostrados na Figura 5 do Anexo 4. Os valores ao redor de 23 GPa para a
dureza são consistentes com a literatura para Si3N4 amorfo. Porém, a dureza diminui
acentuadamente com a temperatura do substrato. O motivo deste decréscimo está associado
com o tipo de tensão interna nos filmes. Embora não tenhamos feito observação experimental
das tensões internas, de acordo com a literatura, nas pressões de gás do plasma aqui utilizadas,
o stress interno é do tipo compressivo. Então, o decréscimo da dureza para temperaturas de
deposição acima de 200 oC pode ser atribuído a relaxação da tensão compressiva interna. O
58
mesmo mecanismo pode, de acordo com a literatura, explicar o decréscimo do módulo de
Young, enquanto que o valor de H3/E2 permanece constante, ao redor de 0.25 GPa.
Os filmes de Si3N4 do presente trabalho foram submetidos a tratamento térmico em
atmosfera de 18O2. O objetivo do tratamento térmico em atmosfera de oxigênio é simular
condições de trabalho de ferramentas revestidas. Os resultados de dureza para filmes
depositados em diferentes temperaturas em função da temperatura de posterior tratamento
térmico (ou annealing) em oxigênio são mostrados na Figura 6a do Anexo 4. Em geral,
observa-se um decréscimo da dureza para annealing até 200 oC e, à partir daí, a dureza volta a
aumentar, atingindo o mesmo valor máximo obtido para deposição a 100 oC sem annealing
posterior. A Figura 6b do Anexo 4 mostra os valores de E e de H3/E2 em função da
temperatura de deposição de amostradas posteriormente tratadas termicamente em oxigênio a
1000 oC. Como o módulo de Young cai continuamente, isto resulta num aumento de H3/E2 até
um valor máximo de 0.5 para a maior temperatura de deposição, 500 oC.
O comportamento descrito no parágrafo anterior pode ser discutido à luz de resultados
de GAXRD mostrados na Figura 7 do Anexo 4, obtidos após tratamento térmico em oxigênio
a diferentes temperaturas. Na temperatura de annealing de 1000 oC, observa-se claramente a
cristalização na fase β-Si3N4, além da fase α-Si3N4 já observada anteriormente. Podemos
discutir o que foi observado, admitindo uma competição entre a relaxação das tensões
compressivas, que favorecem o decréscimo da dureza, e a cristalização numa fase estável, que
favorece o aumento da dureza. No caso de annealing em oxigênio a 1000 oC, o efeito da
cristalização vence a competição e a dureza aumenta.
59
4.4. Perfis de concentração em profundidade de oxigênio e nitrogênio após annealing em
18O2 e composição dos filmes
Os perfis de concentração de oxigênio e nitrogênio foram determinados por NRP,
usando as reações 18O(p,α)15N e 15N(p,α)18O próximos as ressonâncias a 151 e 429 keV,
respectivamente. As curvas de excitação da reação 18O(p,α)15N e os perfis de 18O são
mostrados na Figura 8 e as curvas de excitação e perfis de 15N na Figura 9 do Anexo 4. Os
filmes de Si3N4 resistem muito bem à oxidação em altas temperaturas, pois mesmo após
tratamento térmico a 1000 oC por 4 h, a penetração máxima de oxigênio no filme de Si3N4
atinge apenas 9 nm. Da mesma forma, vê-se que nitrogênio é parcialmente perdido da mesma
região próxima a superfície do filme, provavelmente substituído por oxigênio.
Efetivamente, as análises por XPS mostradas na Figura 10 do Anexo 4 revelam a
existência exclusivamente de ligações Si-N para os filmes como depositados, enquanto que os
filmes tratados termicamente em oxigênio apresentam também ligações Si-O-N.
4.5. Atrito em escala nanoscópica
O comportamento dos filmes de Si3N4 em ensaios de nanoatrito também foi estudado
aqui, após tratamento térmico em oxigênio. Os ensaios de atrito foram realizados no mesmo
equipamento de nanoindentação, realizado com módulo para testes nanotribológicos. O
avanço da ponta foi de 1 µm.s-1 e distância total de 300 µm.
Na Figura 3 do Anexo 5 são mostrados os coeficientes de atrito em função da distância
de deslizamento para diferentes cargas normais. Os filmes foram depositados a 500 oC e
posteriormente tratados termicamente em oxigênio a 500 e 1000 oC. Os valores médios dos
coeficientes de atrito também são apresentados em cada figura. Para as amostras tratadas
termicamente, existe substancial flutuação dos valores dos coeficientes de atrito, o que foi
60
confirmado por medidas repetidas. Por outro lado, antes de tratamento térmico, os
coeficientes de atrito podem ser considerados independentes de carga, enquanto que após
tratamento térmico os coeficientes de atrito variam substancialmente com a carga.
Como o coeficiente de atrito também depende da rugosidade da superfície, isto foi
determinado aqui, com resultados mostrados na Figura 4 do Anexo 5. Nota-se que, assim
como o coeficiente de atrito, a rugosidade dos filmes também aumenta com o aumento da
temperatura de annealing em oxigênio. Assim, provavelmente, o aumento destas duas
grandezas está associado ao aumento da rugosidade.
Novos resultados que ajudam a entender as observações descritas até aqui são
apresentados a seguir. A Figura 5 do Anexo 5 mostra medidas de profundidade de indentação
com ponta Berkovich com 5, 10 e 20 mN em filmes depositados a 500 e tratados
termicamente em oxigênio a 1000 oC. As profundidades de indentação são 110, 190 e 260
nm, respectivamente. Nestas condições de indentação, os filmes não sofreram descolamento
(spalling) e, consequentemente, os coeficientes de atrito medidos correspondem aqueles de
filmes bem aderidos. A situação de indentação com uma ponta Berkovich é representada
esquematicamente na Figura 5a do Anexo 5. Cálculos trigonométricos dão um comprimento
máximo do lado de contato projetado de 900 nm para uma indentação de 260 nm, consistente
com a observação por MEV mostrada na Figura 5b do Anexo 5, na qual a largura do trilho de
desgaste é de aproximadamente 1000 nm. Considerando uma ponta de Berkovich ideal, a
proporção da camada de oxinitreto em contato com o indentador é 17.4, 10.3 e 7.5%, para
cargas normais de 5, 10 e 20 mN, respectivamente. Assim, profundidades de penetração
menores resultam numa proporção maior de óxido em contato com o indentador e, portanto,
um efeito de lubrificação maior.
61
Os resultados apresentados acima podem ser discutidos à luz de modelos de química dos
cristais. Existe uma relação bem estabelecida entre potenciais iônicos (ϕ = Z/r) e coeficiente
de atrito de vários óxidos [57,58]. Aqui, Z representa a carga catiônica e r o raio catiônico.
Óxidos com potenciais iônicos maiores (cátions com carga maior e/ou raio menor) possuem
cátions blindados pelos ânions ao redor e, portanto, seus coeficientes de atrito são menores.
Aqui, nós estendemos a aproximação da química de cristais aplicando-a a óxidos e nitretos,
assim como adotando a densidade de carga, localizada nos centros catiônicos, ao invés do
numero de valência usado até agora. De acordo com a literatura [59,60], Z/r vale 2.03 para
Si3N4 e 3.59 para SiO2. Portanto, o coeficiente de atrito a baixa carga de Si3N4 parcialmente
oxidado deve ser menor do que o de Si3N4, concordando com os resultados apresentados aqui.
4.6. Conclusões parciais
Os filmes de Si3N4 do presente trabalho são essencialmente amorfos, com exceção
daq1ueles depositados a 500 oC. Estes filmes são estequiométricos para qualquer temperatura
de deposição acima de 100 oC. A dureza e o módulo de Young variam com a temperatura do
substrato, o que é atribuído a relaxação de stress compressivo interno nos filmes. Os filmes de
Si3N4 resistem muito bem à oxidação em altas temperaturas, com uma profundidade máxima
de penetração do oxigênio de 7.5 nm após 1 h de oxidação. O comportamento da dureza após
annealing em oxigênio resulta, possivelmente, da competição entre dois processos: a
relaxação de tensões internas, que tende a diminuir a dureza e a cristalização dos filmes, que
tende a aumentar a dureza. Como a cristalização prevalece para annealing a 1000 oC, os
filmes mantém a sua alta dureza nestas temperaturas.
O coeficiente de nano-atrito a baixa carga de filmes após oxidação diminui
substancialmente devido à presença da fina camada de oxinitretos formada. A química dos
62
cristais, estendida pelo cálculo dos potenciais iônicos Z/r em SiO2 e Si3N4 mediante a adoção
da densidade de carga em sítios catiônicos, ao invés do número de valência até aqui utilizado,
pode explicar este fenômeno. Efetivamente, o potencial iônico do SiO2 é quase o dobro
daquele do Si3N4 e, portanto, o coeficiente de atrito de uma camada de Si3N4 parcialmente
oxidada é menor do que o coeficiente de atrito de um filme de Si3N4.
63
CAPÍTULO 5
5. Nitreto de titânio sobre titânio
Como exposto no Capítulo de Introdução desta tese, revestimentos protetores de nitreto
de titânio (TiN) são largamente utilizados da indústria metal-mecânica e os estudos sobre este
revestimento são realizados há várias décadas. O diagrama de fases para o sistema N-Ti é
mostrado na Figura 34 [39]. No presente trabalho, estudamos transporte atômico e
composição ao longo do filme e interfaces, buscando contribuir para a compreensão do
fenômeno de adesão entre o revestimento e o substrato. Para tanto, correlações entre a
composição das interfaces e a adesão do revestimento ao substrato foram estabelecidas, bem
como foi investigada a camada de adesão e sua correlação com a adesão do filme ao substrato.
Figura 34 – Diagrama de fases para o sistema N-Ti.
64
Na maioria das aplicações industriais, é utilizada uma camada de transição entre o
substrato e o revestimento, chamada de camada de adesão, a qual consiste, normalmente, em
um filme fino de um metal de transição [61]. No caso de revestimentos de TiN é comumente
utilizado um filme de Ti, portanto a estrutura formada fica sendo [substrato de aço + filme de
Ti + filme de TiN], como mostrado na Figura 35. Esta camada de adesão produz um aumento
significativo da adesão dos filmes ao substrato. Porém, os mecanismos responsáveis pelo
aumento da adesão não foram bem esclarecidos ainda, devido à complexidade do fenômeno
de adesão. Neste último, estão envolvidos fenômenos de interface em escala atômica, ou seja,
a maneira pela qual os átomos do filme e substrato estão distribuídos e ligados, sendo,
portanto necessário técnicas avançadas de análise de superfície.
Figura 35 – Estrutura de TiN com camada intermediária de Ti sobre aço nitretado.
O substrato de aço aqui utilizado é o AISI M2, o mesmo que é utilizado para confecção
de discos de corte, fresas e brocas. Também foi utilizada a nitretação a plasma do substrato de
aço, outro processo amplamente empregado no setor industrial. A nitretação a plasma é um
processo comumente utilizado em situações como esta, ou seja, quando há deposição de
revestimentos protetores em aços. O principal objetivo da nitretação neste caso é aumentar a
dureza na região próxima à superfície do substrato. Com isso, evita-se a diferença abrupta da
dureza do substrato em relação à do filme, visto que em muitas situações estas podem chegar
a diferenças de uma ordem de grandeza [62]. Com a utilização destes processos de superfície,
M2
Ti
M2 nitretado
TiN
65
ou seja, nitretação a plasma do substrato, revestimento com filme de TiN (estrutura duplex),
além da camada intermediária de Ti, há um ganho significativo principalmente em aumento
da adesão e resistência ao desgaste [63,64,65].
No estudo aqui realizado, os substratos de AISI M2 foram nitretados a plasma em
condições semelhantes àquelas que a indústria utiliza e, após nitretados, filmes de TiN ou
TiN/Ti foram depositados pela técnica de magnetron sputtering reativo. A temperatura de
deposição escolhida para o presente estudo, 450 oC, é a mais comumente utilizada em
processos industriais.
O presente estudo investiga a composição química e o transporte atômico dos diferentes
elementos nas regiões de interface. Buscamos correlacionar estas características físico-
químicas com o aumento da adesão de um filme de TiN ao substrato de aço quando uma
camada intermediária de Ti é introduzida. Para viabilizar o estudo do transporte atômico do
N, foi utilizado em alguns casos o gás N2 isotopicamente enriquecido com seu isótopo 15N. As
estruturas estudadas podem ser vistas na Figura 36.
Figura 36 – Estruturas estudadas no presente trabalho.
66
5.1. Resultados experimentais
A Figura 1a do Anexo 6 mostra resultados de RBS para filmes de TiN de 20 nm de
espessura depositados sobre substrato de carbono (grafite). O espectro mostrado confirma a
razão Ti/N de aproximadamente 1 e uma pequena contaminação com oxigênio tanto na
superfície quanto na interface do filme de TiN. Este fator é importante para o desempenho do
filme, visto que oxigênio ao longo do filme diminui sua dureza. Afora esta, verificou-se
experimentalmente que não há nenhuma outra contaminação nas amostras e que o oxigênio
está presente somente na superfície e nas interfaces.
O mesmo perfil de oxigênio é observado por NRP, usando a reação 18O(p,α)18O ao
redor da ressonância a 151 keV, conforme mostrado na Figura 1b do Anexo 6.
Para amostradas preparadas nas diferentes rotas de deposição de filmes mostradas
acima, foram determinadas as curvas de excitação para a reação 15N(p,α)15N ao redor da
ressonância a 429 keV e os perfis de 15N delas extraídos, como mostrados na Figura 2 do
Anexo 6. No caso de aços nitretados em atmosfera de 15N e após revestidos com TiN ou com
TiN/Ti por sputtering reativo em plasma contendo N2 natural, o 15N do aço nitretado em 15N2
propaga-se até atingir a superfície do filme. Nos filmes depositados em plasma contendo 15N2,
o 15N é observado migrando até a região do substrato nitretada em N2, sendo que as
concentrações de 15N são maiores em TiN/aço nitretado do que em TiN/Ti/aço nitretado. Este
ultimo fato é confirmado para amostras nitretadas em 15N e, após, revestidas com filmes de
TiN em atmosfera de N2. Portanto, a camada intermediária de Ti constitui uma região de
difusão rápida, que favorece a migração de N.
As análises de composição química das nano-estruturas aqui estudadas foram
determinadas por XPS. A Figura 3 do Anexo 6 mostras as regiões de fotoelétrons N 1s, O 1s e
Ti 2p. Na estrutura TiN/Ti/aço nitretado, a componente mais intensa da região N 1s é
67
associada a N ligado em nitretos metálicos tais como TiN, CrN e FeN, bem como uma
componente menos intensa associada a N em oxinitretos metálicos. Já para as estruturas
TiN/aço nitretado, a componente mais intensa é associada a N ligado em TiN, além do
oxinitreto de titânio, o qual neste caso é relativamente mais significante do que em TiN/Ti/aço
nitretado. Os fotoelétrons O 1s das estruturas TiN/Ti/aço nitretado têm uma componente
dominante associada a O em TiO2, a qual não pode ser muito bem distinta de CrOx e FeOx,
além de uma componente menor associada a oxinitretos. Para as estruturas TiN/aço nitretado,
parece que a camada intermediária de Ti favorece a formação de óxidos e oxinitretos, em
detrimento à formação de TiN. Os fotoelétrons Ti 2p confirmam estas composições, mas não
há evidencia de Ti metálico.
Perfis de Ti foram determinados por MEIS, com uma resolução de 0.5 nm. O substrato
usado neste caso particular foi Si, uma vez que os elementos metálicos do aço mascarariam
todo o sinal de Ti. Os resultados são mostrados na Figura 4a do Anexo 6. Os filmes foram
depositados a 450 oC e, posteriormente, aquecidos a 550 e 650 oC. O espectro não mostra uma
transição abrupta entre o TiN e o Ti, pois a concentração de Ti nestes dois materiais é muito
semelhante. A transição na interface filme/Si como depositado, no entanto, é abrupta. Para as
temperaturas superiores a 450 oC, observa-se claramente uma migração de Ti para o Si,
indicando que uma migração de Ti ainda bem maior deve ocorrer do Ti para o aço nitretado.
Finalmente, a composição elementar da camada atômica mais superficial das amostras
foi analisada por LEIS. Os espectros de retroespalhamento são mostrados Figura 4b do Anexo
6, para íons de hélio incidentes a 1 keV em amostras TiN/Ti/aço nitretado e para TiN/aço
nitretado.
Como LEIS é uma técnica sensível somente à superfície, os espectros da Figura 4b
descrevem qualitativamente a composição das superfícies. Vê-se que, na superfície mais
68
externa, O substitui N mediante por mecanismo de troca, formando TiO2. O fato mais
chocante, no entanto, é a presença na superfície dos metais de maior concentração na liga do
substrato de aço, tais como Fe, Cr, Mo, Si e W. Além disto, vê-se que a concentração destes
elementos metálicos é muito maior para estruturas TiN/Ti do que para estruturas TiN,
consistentemente com observações prévias deste trabalho.
5.2. Conclusões parciais
Utilizando o traçador isotópico 15N e a técnica de NRP, observou-se a migração de
átomos de nitrogênio ao longo das interfaces e dos filmes de Ti e TiN. Essa migração produz
uma região de composição variando gradualmente, ao invés de interfaces abruptas, relaxando
as tensões de interface e assim propiciando um aumento significativo da força de adesão.
Como pode ser observado pelos resultados experimentais, em estruturas que contém a camada
intermediária de adesão, há uma migração mais pronunciada de átomos de nitrogênio do filme
para o substrato e do substrato para o filme. Ao contrário, para a estrutura TiN/aço nitretado, a
difusão é bem menor, uma vez que o TiN é bem conhecido por ser uma barreira à difusão.
As ligações químicas presentes nestes filmes, determinadas por XPS, são características
de nitretos, óxidos e oxinitretos de titânio. A presença de óxidos e oxinitretos na região
superficial é devida à oxidação ao ar, tendo um efeito benéfico, pois óxidos e oxinitretos são
lubrificantes sólidos que contribuem para reduzir o atrito.
A migração de átomos de titânio também foi observada aqui e, com o aumento da
temperatura, observou-se uma maior quantidade de átomos de Ti migrando do filme para o
substrato. As medições foram realizadas com silício como substrato, devido ao fato do aço
conter outros elementos pesados que interferem no resultado do método de perfilometria aqui
utilizado, ou seja MEIS. No silício, a difusividade de todos os elementos é menor do que no
69
aço e, portanto, com a constatação de que há migração de Ti em silício, haverá migração
ainda maior de Ti no aço.
Outro resultado importante observado aqui foi a migração de elementos de liga do aço
nitretado ao longo do filme, chegando até a superfície. Para as estruturas de TiN, como são
barreiras para a difusão, essa migração se deu em menor intensidade, já nas estruturas TiN/Ti
a migração foi bastante pronunciada.
Com este estudo, algumas correlações foram obtidas:
1) Em estruturas do tipo TiN/Ti/aço, há maior migração de átomos através das
interfaces do que em estruturas do tipo TiN, bem como maior migração de
elementos de liga do substrato para o filme;
2) Em estruturas sem a camada intermediária de Ti, o TiN age como barreira à difusão
dos átomos tanto do filme quanto do substrato. Portanto a camada intermediária de
Ti promove a interdifusão de todas as espécies químicas.
3) Assim sendo, estruturas do tipo TiN/Ti geram interfaces com variação mais gradual
de composição, ao invés de interfaces abruptas. Tal variação gradual da composição
resulta em relaxação das tensões de interface que são as responsáveis pelo ganho de
adesão. A variação gradual de composição e a grande mobilidade atômica durante a
formação do filme são responsáveis pela excelente adesão dos filmes de TiN em
substratos de aço. Outro resultado observado, foi o fato que os revestimentos de TiN
oxidam quando exposto ao ar, com isso essa camada oxidada atua como lubrificante
sólido em operações de usinagem.
70
6. Conclusões finais e perspectivas
O presente trabalho atingiu, em alguns casos, sua finalidade maior, contribuir para
estabelecer correlações entre estrutura e propriedades de certos revestimentos de filmes finos.
No caso de revestimentos com filmes de VC, foi estabelecida uma correlação entre
estequiometria e propriedades mecânicas: a dureza e o módulo de elasticidade aumentam com
o aumento da razão C/V, atingindo um máximo para C/V = 1, enquanto que o módulo de
elasticidade até ruptura, H3/E2, tem seu valor máximo para C/V = 1.2. Além disto, pode-se
prever com base no critério H3/E2, que estes filmes reduzem substancialmente o desgaste do
componente de aço revestido, o que é largamente comprovado por ensaios de desgaste do tipo
pino-no-disco em aço revestido com filmes VC.
O comportamento mecânico e tribológico dos revestimentos com filmes VC pode ser
atribuído à compactação dos filmes pelo aumento na temperatura de deposição, porém isto só
é verdade até uma certa concentração de C intersticial, no caso até 1. Acima de C/V = 1, o
excesso de C promove a formação de clusters de C que constituem caminhos fáceis para
penetração da ponta de indentação. Quanto a resistência ao desgaste, C intersticial, bem como
uma certa quantidade de clusters nanoscópicos de C, ainda que pequena, constituem excelentes
candidatos a lubrificantes sólidos. O papel do grafite como lubrificante sólido é bem
conhecido, mas o papel de nanoclusters de C não é bem conhecido e o presente trabalho abre
uma janela nesta direção. Não pode ser negligenciado aqui o papel da estrutura intersticial
octaédrica, mais estável, capaz de moderar o desgaste abrasivo.
A corrosão de aço AISI H12 revestido com filmes VC também foi fortemente reduzida.
Porém, embora o efeito protetor já se manifeste a concentrações correspondentes a C/V
ligeiramente maiores do que 1, diferentemente das propriedades mecânicas e tribológicas, a
proteção máxima é obtida para o maior valor de C/V aqui utilizado, ou seja 2.5. Por outro
lado, a proteção é máxima para o maior valor da temperatura de deposição, ou seja, 450 oC.
71
Quanto à temperatura de deposição, um aumento de 13% na densidade real dos filmes de
CV, pode ser responsável por mais e melhores barreiras ao transporte de espécies corrosivas
pela simples compactação dos filmes depositados a maiores temperaturas.
Outro causa possível para o aumento da proteção contra a corrosão em temperaturas de
deposição mais altas está baseada no fato de, embora concentrações maiores de C, como
C/V = 2.5, aumentarem a resistência à corrosão, a quantidade de nanoclusters é
aproximadamente a mesma para todos C/V > 1. Assim, a maior resistência à corrosão dos
filmes VC pode ser devida à migração de C de sítios intersticiais tetraedrais para sítios
intersticiais octaedrais em temperaturas de deposição mais altas, resultando numa maior
disponibilidade dos sítios intersticiais tetraedrais, os quais são sítios mais reativos do C.
No estudo aqui realizado de revestimentos com filmes Si3N4, lembramos que os filmes
de Si3N4 do presente trabalho são essencialmente amorfos, com exceção daqueles depositados
a 500 oC. Estes filmes são estequiométricos para qualquer temperatura de deposição acima de
100 oC. A dureza e o módulo de Young variam com a temperatura do substrato, o que é
atribuído a relaxação de stress compressivo interno nos filmes. O comportamento da dureza
após annealing em oxigênio resulta, possivelmente, da competição entre dois processos: a
relaxação de tensões internas, que tende a diminuir a dureza, e a cristalização dos filmes, que
tende a aumentar a dureza. Como a cristalização prevalece para annealing a 1000 oC, os filmes
mantém a sua alta dureza nestas temperaturas.
O coeficiente de nano-atrito a baixa carga dos filmes após oxidação diminui
substancialmente devido à presença da fina camada de oxinitretos formada. A química dos
cristais, adotando a densidade de carga em sítios catiônicos, ao invés do número de valência
até aqui utilizado, pode explicar este fenômeno. Efetivamente, o potencial iônico do SiO2 é
quase o dobro daquele do Si3N4 e, portanto, o coeficiente de atrito de uma camada de Si3N4
parcialmente oxidada é menor do que o coeficiente de atrito de um filme de Si3N4.
72
No caso de revestimento com estruturas de filmes finos do tipo TiN/Ti, a boa adesão
verificada em aplicações industriais de revestimentos protetores de alta dureza sobre aços
nitretados pode ser correlacionada com a distribuição das diferentes espécies químicas ao
redor das interfaces durante o processo de deposição. Realmente, no caso específico de filmes
TiN/aço nitretado e TiN/Ti/aço nitretado, ocorre migração de N e Ti para o aço nitretado e dos
elementos componentes da camada nitretada do aço para o filme depositado. A mudança de
composição gradual nas regiões próximas às interfaces e a mobilidade atômica durante a
formação desses filmes, favorecem o relaxamento das tensões de interface, as quais são
originadas em mudanças abruptas da composição, defeitos de rede cristalina e ligações
incompletas.
As ligações químicas formadas durante a deposição nas regiões próximas à interface
também tem um papel importante no aumento da adesão. Realmente, verificou-se uma
distribuição de nitretos e oxinitretos metálicos nessas regiões, ao invés de transições abruptas
de aço para metal (Ti) ou de aço para composto (TiN). Os compostos formados também
relaxam tensões de interface e reforçam as ligações químicas na transição aço/revestimento,
aumentando assim a adesão do filme ao substrato.
A presença de uma camada intermediária de Ti entre o revestimento protetor de TiN e o
aço nitretado parece ser uma contribuição adicional para a adesão porque aumenta a migração
de átomos através das interfaces. Assim sendo, a presença da camada intermediária de Ti,
embora introduzindo novas interfaces, não aumenta as tensões de interface, pois as transições
de composição são suaves e não abruptas. Isto é comprovado pelo fato de, durante o processo
de deposição, todo Ti da camada intermediária (nanoscópica) ter sido convertido em
compostos de nitretos e oxinitretos.
Tendo em vista o que foi atingido no presente trabalho, colocam-se algumas
perspectivas para a continuação em direções que podem fazer avançar o conhecimento das
73
correlações entre estrutura e propriedades de revestimentos com filmes finos, assim como suas
aplicações.
Uma direção a ser seguida é a otimização de filmes, como o VC aqui estudado, para
obter condições de preparação, composição e outras características físico-químicas ótimas na
aplicação industrial. Mais especificamente, revestimentos resistentes, ao mesmo tempo, ao
desgaste, a corrosão, e à perda de dureza em trabalho a altas temperaturas. Embora lançadas
algumas bases aqui, isto necessita ainda de muito trabalho de pesquisa.
Da mesma forma, revestimentos com filmes Si3N4 foram mostrados aqui como
preservando sua dureza em altas temperaturas. Porém, quando trabalhando industrialmente,
estes filmes sofrem também corrosão úmida em altas temperaturas e desgaste corrosivo. O
efeito destes processos sobre a dureza após trabalho em altas temperaturas ainda deve ser
investigado.
Finalmente, devido à sua grande importância industrial, os estudos de correlações entre
adesão do revestimento ao substrato e as características físico-químicas dos filmes merecem
ser continuados.
Daqui para frente, o esforço de pesquisa será dirigido para a investigação de dois
sistemas mais avançados de revestimentos protetores:
Revestimentos nano-estruturados do tipo duplex, que consistem em depositar sobre o
aço nitretado à plasma multicamadas de filmes finos de diferentes combinações de dois
materiais, com período de repetição em espessuras tais que seja atingida a ultradureza;
Revestimentos protetores de filmes finos constituídos de diferentes nanopartículas
diluídas em diferentes matrizes, tais como, partículas de Pt, MoS2, SiC em matrizes de Si3N4,
SiO2 amorfo, TiO2 e outras.
74
REFERÊNCIAS BIBLIOGRÁFICAS
[1] Williams, W.S.; Int. J. Refract. Met. Hard Mater., Electrical properties of hard materials, 1999, 17, 21. [2] Tessier, P.Y.; Pichon, L.; Villechaise, P.; Linez, P.; Angleraud, B.; Mubumbila, N.; Fouquet, V.; Straboni, A.; Milhet, X.; Hildebrand, H.F.; Diamond Relat. Mater., Carbon nitride thin films as protective coatings for biomaterials: synthesis, mechanical and biocompatibility characterizations, 2003, 12, 1066. [3] ASM International Handbook Committee; Engineering, Metals Handbook: Surface., 1994, v. 5. [4] Bunshah, R.F.; Handbook of deposition technologies for films and coatings; 2ª Edição. New Jersey: Noyes Publications, 1994. [5] Quinto, D.T.; Int. J. Refract. Met. Hard Mater., Technology perspective on CVD and PVD coated metal-cutting tools, 1996, 14, 7. [6] Strafford, K.N.; Surf. Coat. Technol., Tribological properties of coatings – expectations, performance and the design dilemma, 1996, 81, 106. [7] Subramanian, C.; Stratford, K.N.; Wilks, T.P.; Ward, L.P.; Journal of Materials Processing Technology, On the design of coating systems: metallurgical and other considerations, 1996, 56, 385. [8] Aguzzoli, C.; Figueroa, C.A.; Soares, G.V.; Baumvol, I.J.R.; J. Mater. Sci., Physicochemical and structural characteristics of TiC and VC thin films deposited by DC reactive magnetron sputtering, 2010, 45, 4994. [9] Aguzzoli, C.; Marin, C.; Figueroa, C.A.; Soares, G.V.; Baumvol, I.J.R.; J. Appl. Phys., Physicochemical, structural, and mechanical properties of Si3N4 films annealed in O2, 2010, 107, 073521. [10] Stueber, M.; Holleck, H.; Leiste, H.; Seemann, K.; Ulrich, S.; Ziebert, C.; J. Alloys Compd., Concepts for the design of advanced nanoscale PVD multilayer protective thin films, 2009, 483, 321. [11] Raveh, A.; Zukerman, I.; Shneck, R.; Avni, R.; Fried, I.; Surf. Coat. Technol., Thermal stability of nanostructured superhard coatings: A review, 2007, 201, 6136. [12] Musil, J.; Surf. Coat. Technol., Hard and superhard nanocomposite coatings, 2000, 125, 322. [13] Zhang, S.; Sun, D.; Fu, Y.; Du, H.; Surf. Coat. Technol., Recent advances of superhard nanocomposite coatings: a review, 2003, 167, 113. [14] North, B.; Surf. Coat. Technol., Six issues for the hard coatings community, 1998, 106, 129. [15] Brundle, C.R.; Evans Jr., C.A.; Wihon, S.; Encyclopedia of materials characterization: Surfaces, Interfaces, Thin Films; Stoneham: Butterworth-Heinemann, 1992. [16] Krug, C.; Superfícies porosas recobertas com metalocenos: análise multivariada envolvendo caracterização com feixes de íons. 2000. Dissertação (Mestrado em Física). Universidade Federal do Rio Grande do Sul, Porto Alegre. [17] Stedile, F.C.; Filmes finos de óxido de estanho: efeito da implantação iônica e de ambientes oxidantes e redutores. 1990. Dissertação (Mestrado em Química). Universidade Federal do Rio Grande do Sul, Porto Alegre. [18] Silva Jr, A. H. de; Estudo de superfícies metálicas utilizando MEIS. 2007. Tese (Doutorado em Física). Universidade Federal do Rio Grande do Sul, Porto Alegre.
[19] Krug, C; Filmes finos dielétricos para dispositivos microeletrônicos avançados. 2003. Tese (Doutorado em Física). Universidade Federal do Rio Grande do Sul, Porto Alegre.
75
[20] Shubeita, S. M; Medida da perda de energia de moléculas de hidrogênio através da técnica de MEIS. 2006. Dissertação (Mestrado em Física). Universidade Federal do Rio Grande do Sul, Porto Alegre. [21] Gusev, E. P.; Lu, H.C.; Gustafsson, T.; Garfunkel, E.; Physical Review B, Growth mechanism of thin silicon oxide films on Si(100) studied by medium-energy ion scattering., 1995, 52, 1759-1775. [22] Brongersma, H.H.; Draxler, M.; de Ridder, M.; Bauer, P.; Surf. Sci. Rep., Surface composition analysis by low-energy ion scattering, 2007, 62, 63–109. [23] Pezzi, R.P.; Avanços na determinação da distribuição em profundidade de elementos leves com resolução subnanométrica utilizando reações nucleares ressonantes. 2004. Dissertação (Mestrado em Física). Universidade Federal do Rio Grande do Sul, Porto Alegre. [24] E.B.O. da Rosa. Filmes finos dielétricos para tecnologia do silício: processamento térmico e caracterização. 2003. Dissertação (Mestrado em Física). Universidade Federal do Rio Grande do Sul, Porto Alegre. [25] Rivière, J.; Myhra, S.; Handbook of surface and interface analysis: methods for problem solving; New York: Marcel Dekker, 1998. [26] Einstein, A.; Ann. Phys., On a heuristic viewpoint concerning the production and transformation of light., 1905, 17, 132. [27] Watts, J.F.; Wolstenholme, J.; An Introduction to Surface Analysis by XPS and AES; New York: John Wiley & Sons, 2003. [28] Hübler, R.; Revestimentos protetores com filmes finos e multicamadas de Ti/TiN. 1994. Tese (Doutorado em Engenharia). Universidade Federal do Rio Grande do Sul, Porto Alegre. [29] Cullity, B.D.; Stock, S.R.; Elements of X-Ray diffraction; 3 ed., Prentice Hall, 2001. [30] Percharsky, V.K.; Zavalij, P.Y.; Fundamentals of Powder Diffraction and Structural Characterization of Materials; New York: Springer, 2005. [31] Colombi, P.; Agnihotri, D.K.; Asadchikov, E.; Bontempi, E.; Bowen, D.K.; Chang, C.H.; Depero, L.E.; Farnworth, M.; Fujimoto, T.; Gibaud, A.; Jergel, M.; Krumrey, M.; Lafford, T.A.; Lamperti, A.; Ma, T.; Matyi, R.J.; Meduna, M.; Milita, S.; Sakurai, K.; Shabel’nikov, L.; Ulyanenkov, A.; Van der Lees, A.; Wiemert, C.; Journal of Applied Crystallography, Reproducibility in X-ray reflectometry: results fromthe first world-wide round-robin experiment, 2008, 41, 143. [32] Figueroa, C.A.; Propriedades microscópicas e macroscópicas de superfície em ligas ferrosas implantadas com nitrogênio. Tese (doutorado em ciências). IFGW-UNICAMP, 2004. [33] ASTM – American Society of Test and Materials. G99-05: Standard test method for wear testing with a pin-on-disk apparatus. USA, 2005. [34] BudinskiI, K.G.; Friction in machine design: Tribological modeling for mechanical designers, ASTM STP 1105, p.89-126, ASTM, Philadelphia, 1991. [35] Ludema, K.C.; Friction, CRC Handbook of Lubrication - Theory & Design, v. 2, CRC Press, p.31-48, 1988. [36] Ludema, K.C.; Friction, wear, lubrication: a textbook in tribology, Boca Raton, CRC Press, p. 257, 1996. [37] Bayer, R.G.; Mechanical wear prediction and prevention; New York, p. 657, 1ª edição, Marcel Dekker, 1994. [38] Mossmann, V.L.F.; Revista Brasileira de Física, Determinação dos Coeficientes de Atrito Estático e Cinético Utilizando-se a Aquisição Automática de Dados., 2002, 24. [39] ASM International Handbook Committee; Engineering, Metals Handbook: Alloy Phase Diagrams., 1994, v. 3.
76
[40] Kraus, W.; Nolze, G.; PowderCell for Windows Version 2.4, 2000. [41] Gentil, V.; Corrosão; Rio de Janeiro: LTC, 3ª edição, 1996.
[42] Kelly, R.G.; Scully, J. R.; Shoesmith, D. W.; Buchheit, R.G.; Electrochemical Techniques in Corrosion Science and Engineering; Marcel Dekker, Inc, New York, 2002.
[43] ASTM – American Society of Test and Materials. G61-86: Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys. USA, 2009. [44] Princeton Applied Research; Eletrochemistry and corrosion overview and techniques; Application Note Corr 4.
[45] Macdonald, J.R.; Annals of Biomedical Engineering, Impedance Spectroscopy, 1992, 20, 289. [46] ASTM – American Society of Test and Materials. G3-89: Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing. USA, 2010.
[47] Orazem, M.E.; Tribollet, B.; Electrochemical Impedance Spectroscopy, John Wiley & Sons, Inc.: New Jersey, 2008.
[48] Princeton Applied Research. Basics of Electrochemical Impedance Spectroscopy, Application Note AC-1. [49] Chim, Y.C.; Ding, X.Z.; Zeng, X.T.; Zhang, S.; Thin Solid Films, Oxidation resistance of TiN, CrN, TiAlN and CrAlN coatings deposited by lateral rotating cathode arc, 2009,517, 4845. [50] Veprek, S.; Veprek-Heijman, M.J.G.; Surf. Coat. Technol., Industrial applications of superhard nanocomposite coatings, 2008, 202, 5063. [51] Derflinger, V.; Brändle, H.; Zimmermann, H.; Surf. Coat. Technol., New hard/lubricant coating for dry machining, 1999, 113, 286. [52] da Silva, M.B.; Wallbank, J.; J. Mater. Process. Technol., Cutting temperature: prediction and measurement methods – a review, 1999, 88, 195. [53] Ziegle, A.; Idrobo, J.C.; Cinibulk, M.K.; Kisielowski, C.; Browning, N.D.; Ritchie, R.O.; Science, Interface Structure and Atomic Bonding Characteristics in Silicon Nitride Ceramics, 2004, 306, 1768. [54] Schmidt, H.; Gruber, W.; Borchardt, G.; Bruns, M.; Rudolphi, M.; Baumann, H.; Thin Solid Films, Thermal stability and crystallization kinetics of sputtered amorphous Si3N4 films, 2004, 450, 346. [55] Toivola, Y.; Thurn, J.; Cook, R.F.; J. Appl. Phys., Influence of deposition conditions on mechanical properties of low-pressure chemical vapor deposited low-stress silicon nitride films, 2003, 94, 6915. [56] Okamoto, H.; J. Phase Equilib. Diffus., Supplemental Literature Review: Section III, 2005, 26, 293. [57] Erdemir, A.; Surf. Coat. Technol., A crystal chemical approach to the formulation of self-lubricating nanocomposite coatings, 2005, 200, 1792. [58] Erdemir, A.; Li, S.; Jin, Y.; Int. J. Mol. Sci., Relation of Certain Quantum Chemical Parameters to Lubrication Behavior of Solid Oxides, 2005, 6, 203. [59] Liu, Z.; Sugata, S.; Yuge, K.; Nagasono, M.; Tanaka, K.; Kawai, J.; Phys. Rev. B, Correlation between chemical shift of Si Kα lines and the effective charge on the Si atom and its application in the Fe-Si binary system, 2004, 69, 035106. [60]Zhao, G.L.; Bachlechner, M.E.; Phys. Rev. B, Electronic structure and charge transfer in α- and β-Si3N4 and at the Si(111)/Si3N4(001) interface, 1998, 58, 1887. [61] Huang, J.-H.; Ouyang, F.-Y.; Yu, G.-P.; Surf. Coat. Technol., Effect of film thickness and Ti interlayer on the structure and properties of nanocrystalline TiN thin films on AISI D2 steel, 2007, 201, 7043.
77
[62] Kieckow, F.; Kwietniwski, C.; Tentardini, E.K.; Reguly, A.; Baumvol, I.J.R.; Surf. Coat. Technol., XPS and ion scattering studies on compound formation and interfacial mixing in TiN/Ti nanolayers on plasma nitrided tool steel, 2006, 201, 3066. [63] Zukerman, I.; Raveh, A.; Kalman, H.; Klemberg-Sapieha, J.E.; Martinu, L.; Wear, Thermal stability and wear resistance of hard TiN/TiCN coatings on plasma nitrided PH15-5 steel, 2007, 263, 1249. [64] Lee, S.Y.; Surf. Coat. Technol., Mechanical properties of TiNx/Cr1-xN thin films on plasma nitriding-assisted AISI H13 steel, 2005, 193, 55. [65] Klimek, K.S.; Gebauer-Teichmann, A.; Kaestner, P.; Rie, K.-T.; Surf. Coat. Technol., Duplex-PACVD coating of surfaces for die casting tools, 2006, 201, 5628.
ANEXOS
ANEXO 1
Thin Solid Films 517 (2009) 6493–6496
Contents lists available at ScienceDirect
Thin Solid Films
j ourna l homepage: www.e lsev ie r.com/ locate / ts f
Carbon occupancy of interstitial sites in vanadium carbide films deposited by directcurrent reactive magnetron sputtering
E. Portolan a, C.L.G. Amorim a, G.V. Soares a, C. Aguzzoli a, C.A. Perottoni a,b, I.J.R. Baumvol a,b, C.A. Figueroa a,⁎a Centro de Ciências Exatas e Tecnologia, Universidade de Caxias do Sul, Caxias do Sul, 95070-560, Brazilb Instituto de Física, Universidade Federal do Rio Grande do Sul, Porto Alegre, 91509-970, Brazil
⁎ Corresponding author.E-mail address: cafiguer@ucs.br (C.A. Figueroa).
0040-6090/$ – see front matter © 2009 Elsevier B.V. Adoi:10.1016/j.tsf.2009.03.202
a b s t r a c t
a r t i c l e i n f oArticle history:Received 11 October 2008Received in revised form 20 March 2009Accepted 26 March 2009Available online 5 April 2009
Keywords:Vanadium carbideInterstitial carbonPhase transitionReactive magnetron sputtering
Vanadium carbide thin films were deposited on Si substrates by direct current reactive magnetron sputteringfrom a V target in Ar/CH4 plasma, varying the Ar/CH4 partial pressure ratio and substrate temperature. Thefilms were characterized by glancing angle X-ray diffraction and Rutherford backscattering spectrometry.Well defined crystalline structures were obtained for CH4 content higher than 13%. The increase of substratetemperature during deposition diminishes the film thickness slightly while diminishing substantially the C/Vatomic ratio. The intensity ratio of the Bragg peaks (111)/(200) decreases for increasing substratetemperature. This result is discussed in terms of a proposed mechanism for interstitial diffusion of carbonatoms in vanadium carbide thin films with fcc-like crystalline structure and the temperature dependence ofcarbon occupancy of tetrahedral or octahedral interstitial sites.
© 2009 Elsevier B.V. All rights reserved.
1. Introduction
Hard coatings are widely used in surface engineering for wearprotection and friction reduction ofmechanical components. Numerousdifferent coatings are currently available for specific applications [1,2].Among them, vanadium carbide (VC) thin films show high hardness,high melting point, and good chemical stability [3]. However, thecrystalline structure of VC thin films is still open to investigation. On onehand, stoichiometric VC is an interstitial compound, where vanadiumforms the principal lattice and carbon occupies the octahedralinterstitial sites [4]. On the other hand, the equilibrium phase diagramof the V-C system is complex and many phases with differentstoichiometries coexist [5,6]. Furthermore, there is an order–disorderinterplay involving the different VCx phases. The mechanical andtribological properties were reported to be strongly dependent oncarbon content and occupancy of interstitial sites [7]. Although order–disorder phase transformations were already observed [8], the migra-tion of carbon atoms associated with these transformations is stillunclear. So far, only a few works were devoted to the structuralcharacterization of vanadium carbide films obtained by physical vapordeposition techniques. In particular the structure of VCx films depositedby reactive magnetron sputtering has been reported [9], as well as thedeposition characteristics of films by sputtering from a VC target [10].
We report here on the composition and crystalline structure ofvanadium carbide films deposited by DC reactive magnetron sputter-ing. The relative intensities of Bragg peaks (111) and (200) weredetermined for different substrate temperatures during deposition
ll rights reserved.
and compared with simulations of X-ray diffractograms, aiming at theinvestigation of temperature-dependent site occupancy of the carbonatoms in the interstices of the vanadium carbide fcc-like crystallinestructure.
2. Experimental details
The vanadiumcarbide filmswere deposited on Si(100) substrates byDC reactive magnetron sputtering from a pure V target in Ar/CH4
plasma, always at a total pressure of 3×10−1 Pa and a power density of5.5Wcm−2 in the target. Thebasepressure in the chamberwas10−6 Pa.Two sets of sampleswere produced. In thefirst group, theAr/CH4partialpressure ratio was varied, hereafter referred as the CH4 content in thereactive plasma or [PCH4/(PAr+PCH4)]×100%, keeping the substrateswithout any heating. In the second group, the substrate temperaturewas varied at constant CH4 content of 15%.
The thickness and C/V average ratios of the vanadium carbide filmswere determined by Rutherford backscattering spectrometry (RBS) of2 MeV He+ ions in channeling geometry [11]. The vanadium carbidefilm deposition rate was 0.3 nm s−1 without any heating. Thecrystalline structure of vanadium carbide films was determined byglancing angle X-ray diffraction (GAXRD) in a Shimadzu XRD-6000diffractometer, using Cu Kα (U=40 kV and I=30 mA) radiation at anincidence angle of 2°. X-ray diffraction pattern simulations wereperformed with the Powder Cell code [12].
3. Results and discussion
Fig. 1 shows the GAXRD patterns of vanadium carbide films fordifferent CH4 contents in the reactive plasma keeping the substrates
Fig. 1. Glancing angle X-ray diffractograms from vanadium carbide films for differentCH4 contents in the reactive plasma with substrates kept without any heating.
Fig. 3. (a) Typical RBS spectrum for 2 MeV He+ incident ions from a vanadium carbidefilm on a Si(100) substrate having the b001N axis of the Si substrate oriented along thedirection of incidence of the ion beam (channeling geometry). The inset shows the C
6494 E. Portolan et al. / Thin Solid Films 517 (2009) 6493–6496
without any heating. A very broad line is observed in the lower CH4
content range, which is typical of compounds with low crystallineorder. The crystallinity of the vanadium carbide films increases above13% CH4 content in the reactive plasma, as revealed by the appearanceof two well-defined Bragg peaks at 2θ=37.5° and 43.8° assigned,respectively, to the (111) and (200) planes of a vanadium carbide fcc-like structure.
Fig. 2 shows the GAXRD patterns of vanadium carbide films fordifferent substrate temperatures in the interval 100 to 500 °C, atconstant CH4 content (15%). It can be seen from Fig. 2 that theintensity of the (111) peak decreases with respect to that of the (200)peak as the substrate temperature increases.
Fig. 3(a) shows a typical RBS spectrum for 2MeVHe+ incident ionsfrom a vanadium carbide film on a Si(001) substrate having the b001Naxis of the Si substrate oriented along the direction of incidence of theion beam (channeling geometry). This allows to discriminate betweenthe energy overlapping events corresponding to He+ ions scattered byC atoms in the film from those corresponding to He+ scattered bySi atoms in deeper regions of the underlying Si substrate. The inset inFig. 3(a) shows the C signal in the spectrum after subtraction of the Sibackground. Fig. 3(b) shows the thickness of the vanadium carbidefilms as a function of substrate temperature as determined by RBSwith 5% accuracy, assuming the nominal bulk density of vanadiumcarbide. One can see a slight decrease of the film thickness as thesubstrate temperature increases.
Fig. 4 shows the C/V atomic ratio of vanadium carbide films as afunction of substrate temperature, as determined by RBS. The films have
Fig. 2. Glancing angle X-ray diffractograms fromvanadium carbide films as a function ofsubstrate temperature for 15% CH4 content in the reactive plasma.
signal after subtracting the Si background. (b) Vanadium carbide film thickness, asdetermined by RBS, as a function of substrate temperature. The dashed line is only toguide the eyes.
an excess of carbon at lower substrate temperatures and tend towardsthe stoichiometric C/V=1 composition at higher temperatures.
According to the phase diagram of the V-C system, for C/V largerthan 0.9 some C segregation would occur [5]. However, the presentGAXRD patterns for the film deposited at substrate temperature of100 °C (corresponding to the highest carbon content) did not presentany signal of C segregation or polycrystalline graphite. This fact isconfirmed by Raman spectroscopy (not shown), where in the regionfrom 1200 to 1800 cm−1 no signal that could be assigned to disorder(D) and graphite (G) modes [13,14] in carbon graphitic structures wasdetected. Therefore, one can conclude that carbon atoms must remainin solid solution in the vanadium carbide crystalline structure.
Fig. 5 shows the GAXRD intensity ratio I111/I200 as a function of thesubstrate temperature. It can be seen that the intensity ratio I111/I200decreases as the substrate temperature increases. The dashed line is aguide for the eyes. The dotted line at the bottom of the graph indicates
Fig. 4. C/V atomic ratio as a function of substrate temperature. Carbon and vanadiumcontent in the films were quantified by RBS analysis. The dashed line is only to guide theeyes.
Fig. 6. Carbon atoms (black spheres) in tetrahedral (a) and octahedral (b) interstitialsites. The principal lattice is formed by vanadium atoms (gray spheres).
6495E. Portolan et al. / Thin Solid Films 517 (2009) 6493–6496
the intensity ratio for stoichiometric VC in the most stable statewherecarbon atoms occupy the octahedral sites [5].
The intensity of the GAXRD Bragg peaks depends on theconstructive interference of outgoing X-ray radiation after scatteringby the atoms (essentially by the electrons) which constitute eachatomic plane [15]. Therefore, the peak intensity must increase withincreasing atomic concentration in each plane. In a fcc structure the(111) and (200) planes intersect tetrahedral and octahedral inter-stitial sites, respectively. Taking into account that carbon atomscan occupy, at least in principle, both tetrahedral and octahedralinterstitial sites, the experimental observation that the intensity ratioI111/I200 varies with substrate temperature could be explained by theinter-exchange of carbon atoms between both interstitial sites. Fig. 6represents carbon in tetrahedral (a) and octahedral (b) interstitialsites (totally occupied). We recall here that the tetrahedral config-uration leads to a C/V atomic ratio of 2 (VC2 stoichometry) while theoctahedral configuration leads to a C/V atomic ratio of 1 (VCstoichometry). Since themaximumaverage C/V atomic ratio observedexperimentally by RBS was 1.3, the stoichiometric VC2 compoundcannot be the only component of the film for any substratetemperature. Moreover, previous works [5,9] have reported the VCcompound as the stable phase of the V-C system rather than VC2. Thus,the excess C in the lattice with respect to the VC stoichiometry isdiscussed as follows.
The intensity ratio I111/I200 was simulated, using the C/V atomicratios determined by RBS, for different site occupancies of carbon
Fig. 5. GAXRD I111/I200 intensity ratio as a function of substrate temperature. Theintensity ratio for stoichiometric VC with fcc structure and carbon in octahedralinterstitial sites is also included (dotted line). The dashed line is only to guide the eyes.
atoms in tetrahedral or octahedral sites of a fcc structure of vanadiumcarbide [12]. The simulation shows a clear trendwhereby the intensityratio I111/I200 increases with the increase of the carbon concentrationin tetrahedral sites. Table 1 summarizes the results obtained fromsimulations of three different arrangements: carbon in tetrahedral-only, octahedral-only, or in both types of interstitial sites. Because theintensity ratio I111/I200 decreases with the increase of the substratetemperature, carbon atoms could metastably reside in the tetrahedralinterstices of the vanadium fcc structure when the vanadium carbidefilm is deposited with the substrate kept at relatively low tempera-tures. For higher substrate temperatures, the carbon in tetrahedralsites diffuses to more stable octahedral sites (higher negative energy).The facts presented here concerning C/V ratios (determined by RBS),phases (determined by XRD), and structure simulations do not allowto establish unequivocally whether there are segregated phases of VC(octahedral) or VC2 (tetrahedral). In fact, phase segregation is notnecessary to explain the above mentioned results, since localconfigurations of these two phases can exist within a given unit cellof the material. Thus, we believe that there is a tetrahedral–octahedralcarbon interchange in the principal fcc-like crystalline structure,which depends on the substrate temperature during deposition. Thefilm deposited at room substrate temperature was not included inFig. 2 because of the strong dependence of C2-dimer concentration onsubstrate temperature. Indeed, keeping the substrate close to roomtemperature would yield a high C2-dimer density on surface avoidingcarbon incorporation in either tetrahedral or octahedral sites [16].
Since plasma deposition is a non-equilibrium process, where highenergies are involved [17], the energetic carbon atoms from the plasmacan occupy non-equilibrium interstitial positions like the tetrahedralsites in the vanadiumcarbide fcc structure. At higher temperatures, thelarger mobility of carbon atoms promotes the population of the moststable interstitial site for carbon in the octahedral position.
Other possible explanations for the temperature dependence ofthe I111/I200 ratio were also considered. In fact, among other effectsthat could change the intensity of the XRD peaks, the most importantone is the preferential orientation of the polycrystalline film. Rotatingthe samples during analysis or changing their orientation by 90°whilemaintaining the same experimental set up for GAXRD, yielded only a
Table 1Intensity ratio I111/I200 for different stoichiometries and site occupancies for carbon invanadium carbide interstitials sites simulated with PowerCell [12].
C in interstitials sites VC stoichiometry Intensity ratio I111/I200
All in tetrahedral V0.400C0.600 3.82All in tetrahedral V0.500C0.500 3.33Both, tetrahedral and octahedral V0.500C0.500 2.32Both, tetrahedral and octahedral V0.455C0.555 1.87All in octahedral V0.500C0.500 0.92All in octahedral V0.540C0.460 1.12
6496 E. Portolan et al. / Thin Solid Films 517 (2009) 6493–6496
10% change in the intensity ratios I111/I200. This deviation is wellwithin the experimental uncertainty and practically rules out anypossibility that the effect shown in Fig. 5 may be associated to pref-erential orientation.
The intensity ratios I111/I200 calculated by PowderCell simulations[12] (see Table 1) are significantly smaller than the experimental onesgiven in Fig. 5. This can be understood by recalling that thesimulations are based on a model [12] that takes into account onlythe number of electrons in each atom, not considering chemicalbonding. However, the delocalization of electron densities mightchange the intensities associated with constructive interference atplanes (111) and (200). The high degree of covalent bonding in VC, aswell as the higher electronegativity of carbon as compared tovanadium contribute to localize a higher electron density near carbonatoms. Consequently, higher experimental intensity ratios I111/I200than those foreseen by the simulations are expected to be observedwhen more carbon atoms occupy tetrahedral sites.
Furthermore, the interactions of carbon 2p orbitals with vanadium3dxy, 3dxz, and 3dyz orbitals form covalent bondings in tetrahedralinterstitial sites [19,21]. These chemical bondings provide sufficientenergy for the stabilization of the final structure. Indeed, since anatom (in our case, carbon) can occupy an interstitial position only if itssize is compatible with the available space in the principal network ofatoms (in our case, vanadium), we used a classical model of latticeclosed-package to calculate the ratio of atomic radii for tetrahedraland octahedral structures. The result was that for tetrahedral oroctahedral interstitials the radii ratio (carbon radius/vanadiumradius) must be from 0.225 to 0.414 or from 0.414 to 0.732,respectively [18]. Considering the lattice parameter of stoichiometricVC, a=0.418 nm [19], the vanadium radius must be 0.148 nm. On theother hand, the carbon radius is 0.07 nm [20]. So, the radii ratio is0.474. Strictly speaking, this radii ratio suggests an octahedral positionfor carbon atoms. However, in most cases the classical model isapplied for ionic compounds, whereas VC is a hybrid between covalentand metallic compound, where high hardness and high melting point(covalent properties) and electrical conductivity (metallic property)coexist in the same material [19]. Moreover, there is a difference ofonly 14% between 0.414. (limiting value for tetrahedral to octahedraltransition) and 0.477. In the case of tetrahedral sites, the overlappingof carbon 2p orbitals with vanadium 3dxy, 3dxz, and 3dyz orbitals formscovalent bondings [21]. Thus, the involved energy that results fromcovalent bonds can stabilize this difference and carbon can occupyboth tetrahedral and octahedral sites, where the latter configurationis more stable than the former one. Consequently, carbon atoms donot create major local stress and deformation of the original latticestructure.
4. Conclusions
Vanadium carbide thin films were deposited by DC reactivemagnetron sputtering in Ar/CH4 plasma in a high-vacuum chamber.No evidence of carbon segregationwas observed. The C/V atomic ratioin the films decreases for increasing substrate temperature. Computersimulations of the observed glancing angle X-ray diffractogramsallowed us to attribute the temperature dependence of the intensityratio I111/I200 to a thermally activated inter-change of carbon atomsbetween tetrahedral and octahedral interstitial site occupancies in avanadium carbide fcc-like structure. Thus, by increasing the substratetemperature during deposition, carbon atoms diffuse from less stableinterstitial tetrahedral positions occupied at lower substrate tem-peratures into more stable interstitial octahedral positions.
Acknowledgements
This work was partially sponsored by CNPq (project # 550316/2007-8) and Tramontina Farroupilha S.A. IJRB and CAP are CNPqfellows.
References
[1] J.C. Sanchez-Lopez, D. Martinez-Martinez, C. Lopez-Cartes, A. Fernandez, Surf.Coat. Technol. 202 (2008) 4011.
[2] G. Abadias, A. Michel, C. Tromas, C. Jaouen, S.N. Dub, Surf. Coat. Technol. 202 (2007)844.
[3] R. Riedel (Ed.), Handbook of Ceramic Hard Materials, Wiley-VCH, Germany, 2000.[4] V.N. Lipatnikov, A.I. Gusev, P. Ettmayer, W. Lengauer, J. Phys., Condens. Matter 11
(1999) 163.[5] V.N. Lipatnikov, A.I. Gusev, P. Ettmeier,W. Lengauer, Phys. Solid State 41 (1999) 474.[6] J. Hu, C. Li, F. Wang, W. Zhang, J. Alloys Compd. 421 (2006) 120.[7] H. Liu, J. Zhu, Y. Liu, Z. Lai, Mater. Lett. 62 (2008) 3084.[8] V.N. Lipatnikov, W. Lengauer, P. Ettmayer, E. Keil, G. Groboth, E. Kny, J. Alloys
Compd. 261 (1997) 192.[9] A.Aouni, P.Weisbecker, T.H. Loi, E. Bauer-Grosse, Thin Solid Films 469–470 (2004) 315.[10] M.Y. Liao, Y. Gotoh, H. Tsuji, J. Ishikawa, J. Vac. Sci. Technol., A 23 (2005) 1379.[11] L.C. Feldman, J.W. Mayer, S.T. Picraux, Materials Analysis by Ion Channeling,
Academic Press, New York, 1982.[12] W. Kraus, G. Nolze, PowderCell for Windows Version 2.4, , 2000.[13] P. Paredez, C.A. Figueroa, L.F. Zagonel, F.R. Reichert, C.R.M. Ribeiro, S. Point, C.
Godon, T.M. Minea, F. Alvarez, J. Nanosci. Nanotechnol. 2 (2005) 188.[14] A. Czyzniewski, Thin Solid Films 433 (2003) 180.[15] C. Kittel, Introduction to Solid State Physics, 7th edJohn Wiley & Sons Inc., New
York, 1996.[16] T.M. McCauley, D.M. Gruen, A.R. Krauss, Appl. Phys. Lett. 73 (1998) 1646.[17] M.A. Lieberman, A.J. Lichtenberg, Principles of Plasma Discharges and Materials
Processing, John Wiley & Sons, Inc., New York, 1994.[18] B.M. Mahan, R.J. Myers, University Chemistry, Addison-Wesley Publishing Company,
New York, 1987.[19] L. Benco, Solid State Commun. 94 (1995) 861.[20] J.C. Slater, J. Chem. Phys. 41 (1964) 3199.[21] S.V. Didziulis, K.D. Butcher, S.S. Perry, Inorg. Chem. 42 (2003) 7766.
ANEXO 2
ICAM 2009
Physicochemical and structural characteristics of TiC and VCthin films deposited by DC reactive magnetron sputtering
C. Aguzzoli • C. A. Figueroa • G. V. Soares •
I. J. R. Baumvol
Received: 25 November 2009 / Accepted: 27 February 2010 / Published online: 12 March 2010
Springer Science+Business Media, LLC 2010
Abstract Vanadium carbide and titanium carbide films
were deposited on Si substrates by direct current reactive
magnetron sputtering, varying the substrate temperature
during deposition and the reactive gas (CH4) pressure. The
physicochemical and structural properties of the films
were characterized for stoichiometric films (V/C = 1 and
Ti/C = 1), which display good performance concerning
wear, friction, and corrosion. The techniques used to char-
acterize the films were Rutherford backscattering spec-
trometry in channeling geometry, 12C(a,a)12C nuclear
resonant scattering, glancing angle X-ray diffraction, X-ray
reflectometry, and X-ray photoelectron spectroscopy. The
results revealed that the ideal conditions for deposition of
these films are a CH4 partial pressure of 0.5 9 10-3 mbar
and a substrate temperature of 400 C. In such conditions,
the deposition rates are 7 nm s-1 for TiC and 8.5 nm s-1 for
VC at a target power density of 5.5 W cm-2. The density of
the films, as determined here by X-ray reflectometry, are
slightly higher than those for the bulk materials.
Introduction
Transition metals carbides such as TiC, TaC, VC, and
others are widely used as protective coatings owing to their
high hardness and wear resistance, high thermal and
chemical stability, as well as biocompatibility [1–7].
However, TiC has a poor oxidation resistance at high
temperatures [8, 9]. These applications may involve very
severe working conditions, like in machining, cutting, and
drilling, in which near-surface temperatures may be as high
as 750 C.
The excellent performance against wear of TiC and VC
protective coatings can be foreseen from the hardness (H)
to Young modulus (E) ratios, a parameter commonly used
to evaluate the wear resistance of the coatings [10, 11].
This is the so called elastic strain to failure, which has been
proposed and consistently used [12, 13] to evaluate the
resistance to plastic deformation of thin film coatings and
to predict their resistance to wear. Thus, a high H3/E2 ratio
indicates a high resistance of the coating to plastic defor-
mation and, presumably, a high wear resistance as well,
besides low stiffness. TiC does indeed display very
attractive H3/E2 figures. The frictional properties of these
materials are also superior, owing to the extremely fine
grain dispersion of the thin film coatings [1].
There are many routes to deposit these hard coatings,
like chemical vapor deposition (CVD) [14], pulsed laser
deposition (PLD) [15], and physical vapor deposition
(PVD) [16]. The advantage of PLD and PVD is that with
these techniques we can deposit compound films at lower
substrate temperatures [17, 18]. This is especially conve-
nient in order to preserve the bulk properties of steel
engineering components as obtained by thermal annealing.
Other aspects are also important for the final perfor-
mance of the coatings [7]. One of them is the crystallinity
of the hard coatings, which is directly correlated to the
substrate temperature during deposition [19]: The higher
the substrate temperature, the higher the crystalline order
of the coating. It was also observed that if the content of the
reactive gas changes, the crystallinity changes too [20]. In
the case of vanadium carbide (VC), it was seen that the
partial pressure of the reactive gas (CH4) in the gas mixture
C. Aguzzoli (&) I. J. R. Baumvol
Universidade Federal do Rio Grande do Sul, Porto Alegre,
RS, Brazil
e-mail: caguzzol@ucs.br
C. Aguzzoli C. A. Figueroa G. V. Soares I. J. R. Baumvol
Universidade de Caxias do Sul, Caxias do Sul, RS, Brazil
123
J Mater Sci (2010) 45:4994–5001
DOI 10.1007/s10853-010-4364-0
that supports the plasma has a significant influence on the
crystalline structure [19]. In titanium carbide (TiC) films,
the partial pressure of the reactive gas, either methane or
acetylene, has a strong influence on crystalline phase for-
mation [20, 21] as well as on the hardness of the coatings.
Furthermore, the C excess in TiC films was seen to
decrease the film hardness [20].
In the present work, we investigate the elementary
composition and the physicochemical and structural prop-
erties of TiC and VC films deposited by direct current (DC)
reactive magnetron sputtering. Different contents of CH4
and different substrate temperatures during deposition were
accessed in order to investigate the influence of these
deposition parameters on the physicochemical and struc-
tural characteristics of the films.
Experimental
TiC and VC thin films were deposited on single-crystalline
silicon(001) wafers by DC reactive magnetron sputtering,
using a Ar/CH4 gas mixture. Table 1 gives typical depo-
sition parameters that led to the deposition of stoichiome-
tric TiC and VC films, as described below.
The elementary composition of the films was deter-
mined by Rutherford backscattering spectrometry (RBS)
[22] using He? ions incident at 2 MeV. This method
allows also the determination of film thickness, using the
density of the films obtained from XRR measurements. The
areal densities of Ti, V, and C were determined using
standards of Bi-implanted Si and C-implanted Si. Since the
small C signal in the RBS spectra overlaps the intense Si
substrate signal, rendering it difficult to quantify C, the
channeled-RBS technique [23] was used here, where
the \001[ axis of the Si substrate was aligned with the
direction of incidence of the He? beam, detecting the
backscattered particles at 165 with the direction of inci-
dence of the beam. Although in channeling geometry the
Si-background contribution to the RBS spectra has been
considerably reduced, the quantification of C in the films
still bares an experimental error significantly larger than
that for Ti and V.
In order to reduce the experimental error in C quantifica-
tion, the 12C(a,a)12C resonant scattering at 4.26 MeV [24–26]
was used, taking advantage of the much higher cross section of
this resonance, which is also narrow enough in energy to allow
for C profiling [24–26] in the films. This method increases the
C signal-to-noise ratio by at least a factor of 10 as compared to
RBS, thus improving significantly the accuracy of the C
quantification. A SiC (0001) single-crystalline wafer was used
here as a standard for C quantification.
Glancing angle X-ray diffraction (GAXRD) and X-ray
reflectometry (XRR) analyses were performed using a
Shimadzu XRD-6000 apparatus, with Cu Ka radiation
(k = 1.54 A) at an incidence angle of 2, in order to determine
the crystalline structure of the films and density, respectively.
Chemical analysis was accomplished by X-ray photo-
electron spectroscopy (XPS). An Omicron Multiprobe Sphera
instrument was used, with a Mg Ka (1256.3 eV) X-ray source.
The energy resolution of the spectrometer was 0.9 eV.
Results and discussion
Composition
Typical RBS spectra in channeling geometry for 2 MeV inci-
dent He? ions from TiC and VC samples are shown in Fig. 1.
The insets show the C signal energy regions, after subtraction of
the Si-background contribution. One can verify from these
spectra that the concentration of impurities in the films, for
example O, Fe, Cr, and others are all below the sensitivity limit
of RBS, namely below 1014 at. cm-2 (about 1/10 of a mono-
layer). The presence of impurities would affect significantly the
hardness and the adhesion of the coatings to the substrate.
Figure 2a, b shows typical 12C(a,a)12C resonant scat-
tering spectra at increasing energies of the incident He?
ions, for a TiC/Si and VC/Si thin film samples, starting at
an energy value below the resonance energy of 4.26 MeV.
At the resonance energy, the C peak in the spectrum is
associated to the C contamination layer at the sample
surface [24–26]. For progressively larger energies than the
resonance energy, the C peak area in the spectrum is
directly proportional to the C concentration at increasingly
larger depths [24–26], such that a C profile can be extracted
from the ensemble of 12C(a,a)12C spectra at variable
incident energy [24–26] like those shown in Fig. 2. One
can see that a homogenous distribution of C is observed,
indicating the formation of uniform films.
Figure 3a, b shows the C to Ti ratios as a function of
methane partial pressure for two different substrate
Table 1 Deposition parameters of thin films deposited by DC reac-
tive magnetron sputtering
TiC and VC
Base pressure (mbar)
8.0 9 10-7
Ar partial pressure (mbar)
3 9 10-3
CH4 partial pressure (mbar)
0.5 9 10-3
Source-to-substrate distance (cm)
12
Target power density (W cm-2) 2.7 5.5
Deposition rate (nm min-1) 3.3 7
J Mater Sci (2010) 45:4994–5001 4995
123
temperatures, 20 and 420 C, as determined by RBS and
resonant scattering analyses. For both substrate tempera-
tures, stoichiometric film, C/Ti = V/C = 1 are obtained
for a CH4 partial pressure of 0.5 9 10-3 mbar. Thus, the
present results establish also favorable substrate tempera-
ture and CH4 pressure to deposit TiC/VC multilayers
aiming at superhard coatings.
Figure 4a shows the C to Ti concentration ratio as
a function of substrate temperature during deposition.
Figure 4 shows that at 400 C, the C/Ti and C/V ratios are
close to one, indicating ideal CH4 pressure and substrate
temperature to deposit TiC/VC multilayers. It is worth
recalling here that, since the stoichiometric film presents
high hardness [3, 10], deposition conditions leading to
stoichiometric films is an important issue for any practical
application. However, the same is not necessarily true for
friction and wear characteristics, although the H3/E2
parameter points out and the results in the literature men-
tioned above point out in this direction.
Deposition rates
Figure 5a, b show the TiC and VC film thicknesses as a
function of deposition time, at substrate temperature of
400 C and CH4 partial pressure of 0.5 9 10-3 mbar, for
Fig. 1 Rutherford backscattering spectra of 2 MeV He? incident
particles from a TiC and b VC films deposited on Si(001)
Fig. 2 Yield of the 12C(a,a)12C nuclear resonant scattering near the
resonance energy of 4.26 MeV from a TiC and b VC films on Si
deposited at a substrate temperature of 450 C
Fig. 3 C/Ti ratio versus methane partial pressure at 50 W of target
power for substrates at a room temperature (20 C) and b 420 C.
Line is only to guide the eyes
4996 J Mater Sci (2010) 45:4994–5001
123
two different DC powers, namely 50 and 100 W. The film
thicknesses were calculated based on the experimentally
determined Ti, V, and C areal densities and the densities of
TiC and VC obtained by X-ray reflectometry analysis, as
described below. This leads to the following relations:
1015 Ti cm2 ¼ 0:176 nm, ð1Þ
1015 V cm2 ¼ 0:137 nm: ð2ÞIn Table 1, the figures for the deposition rates of TiC
and VC films are given for 50 and 100 W DC target power,
respectively, as obtained from the linear fit of the data of
Fig. 5.
Crystallographic structure and phases
Figure 6a shows GAXRD from TiC coatings deposited at
different temperatures. One can see that the increase of the
substrate temperature leads to an increase of the intensity
of the fcc TiC (111) and (200) diffraction peaks with
respect to the intensity of the Ti (110) peak. The progres-
sive TiC phase formation with temperature is associated
with the thermally activated surface mobility of the carbon
and titanium atoms.Fig. 4 C/Ti and C/V ratio versus substrate temperature at 50 W:
a Ti/C and b V/C films. Both samples deposited at 0.5 9 10-3 mbar
of CH4. Line is only to guide the eyes
Fig. 5 Film thickness versus deposition time for 50 and 100 W of
target power, at a CH4 partial pressure of 0.5 9 10-3 mbar and
substrate temperature of 400 C for a TiC and b VC
Fig. 6 Diffractograms in h 9 2h geometry from a TiC and b VC
films on Si(001) at different substrate temperatures. The methane
partial pressure is 0.5 9 10-3 mbar
J Mater Sci (2010) 45:4994–5001 4997
123
Figure 6b shows GAXRD from VC coatings deposited
at different substrate temperatures. The same picture as in
TiC is observed, namely the intensities of the VC (111) and
(200) diffraction peaks increase with respect to the V (110)
peak as the substrate temperature increases.
Figure 7a, b show the Ti/TiC and V/VC ratios as
obtained by simulations of the experimental diffractograms
with the PowderCell code [27]. Notice that for substrate
temperatures above 200 C, the metallic V phase is no
longer observed, while for TiC in Fig. 7a this only happens
above 300 C.
Chemical bonding
The chemical bonds of Ti, V, and C in the films were
accessed by XPS. Figure 8a shows the Ti 2p photoelectron
regions from TiC films for substrate temperatures of 20 and
400 C. Three different doublets, corresponding to three
different bond states for Ti are observed, Ti in TiC [28], Ti
in TiO2 [29], and Ti in metallic Ti [30]. Since the
inspection depth of XPS is about 10 nm, the presence of
titanium oxide in this near-surface region of the films is
expected, owing to the affinity of titanium for oxygen,
similarly to TiN films after exposure to air [31]. For 400 C
substrate temperature, the TiC/TiO2 spectral area ratio is
much larger than for 20 C and the intensity of metallic Ti
decreases. This is consistent with the GAXRD results
presented above, where the proportion of the TiC phase
was seen to increase with the increasing of the substrate
temperature. In Fig. 8b, C 1s photoelectron regions for TiC
films are shown. The components C–C1 and C–C2 at
binding energies (BE) of 284.9 and 284.1 eV are assigned
to amorphous carbons (a-C) phases [32–34]. The CCont
(289.5 eV) is assigned to hydrocarbons at the sample sur-
face, while the peak at BE 281.5 eV is assigned to TiC.
Here again, the proportion between the spectral area of the
component assigned to C in TiC films with respect to the
other components is larger for 400 C substrate tempera-
ture than for 20 C. Thus, the XPS results confirm the facts
observed by GAXRD, namely that the formation of the TiC
stoichiometric compound is favored at the higher substrate
temperatures.
V 2p and C 1s photoelectron regions from VC films on
Si [35] are shown in Fig. 9, confirming the general trends
discussed in the last paragraph for TiC, including the
presence of V2O5 in the near-surface region of the films.
The formation of VC and the increase of its proportion with
respect to the other spectral components as the substrate
temperature increases are also observed here.
Film densities and thicknesses
The results of XRR for TiC and VC films on Si, deposited
with the substrates at 400 C, are shown in Fig. 10.
Fig. 7 Metal to compound ratios in thin films at different substrate
temperatures in a TiC and b VC films. Line is only to guide the eyes
Fig. 8 a Ti 2p and b C 1s X-ray photoelectron regions from TiC thin
films on Si
4998 J Mater Sci (2010) 45:4994–5001
123
Simulations of the XRR data [36] allowed the determina-
tion of the film thicknesses and densities, whose figures are
given in Fig. 10. The densities of the films as determined
by XRR are seen to be somehow higher than those for the
bulk materials [37]. This fact was used in the present work
as a correction in the thicknesses determined by RBS and,
consequently, as a correction in the deposition rates.
Correlations with hardness and tribological
performance
The search described above for optimal conditions of
deposition of stoichiometric, crystalline TiC, and VC films
is a critical issue for practical applications, since previous
studies demonstrated that hardness, friction, and wear
behavior of these materials can be strongly influenced by
these physicochemical and structural characteristics [1, 3,
10, 20, 21]. The deposition rate to stoichiometric films is
also an issue of practical interest concerning processing
costs. Thus, C/Ti or C/V ratios of 1, no C segregation in the
films, crystalline structures, and moderate oxide layers in
near-surface regions seem to be essential for good protec-
tive action of the coatings. In the present work, CH4 partial
pressures around 0.5 9 10-3 mbar, substrate temperatures
around 400 C, seem to be optimal to reach the composi-
tional and structural targets mentioned in the previous
paragraph. Under these conditions, typical deposition rates
may be 10 nm min-1 or more, according to the target
power.
We have measured the hardness and elastic modulus for
VC and TiC films for depositions in 0.5 9 10-3 mbar of
CH4, as a function of substrate temperature. The results for
VC films, together with the extracted H3/E2 are given in
Fig. 11. A hardness of 35 GPa as determined here for VC
is comparable to the best results found in the literature. The
data for TiC (not shown) indicate a similar behavior. Thus,
the hardness and elastic moduli determined here point out
to a maximum H3/E2, and therefore a good resistance to
wear, for stoichiometric, crystalline carbide films. Some
mechanical properties like hardness, modulus of elasticity,
and H3/E2 for carbides films from the literature are given in
Table 2. Another criterion has been used to predict the
wear behavior of carbide coatings, namely the combination
of hardness and fracture toughness [38, 39]. Although this
last criterion is also valid, we did not addressed it in the
present work since it is much less used.
Furthermore, the wear resistance of stoichiometric VC
and TiC films deposited on AISI H12 steel were also
approached, using pin-on-disc tests. A large reduction (of
about a factor of 40) on volumetric wear with respect to the
uncoated steel were observed, confirming the previsions of
the H3/E2 criterion. On the other hand, the experimentally
determined densities of the films here produced indicate
Fig. 9 a V 2p and b C 1s X-ray photoelectron regions from VC thin
films on Si
Fig. 10 X-ray reflectometry for a TiC and b VC thin films at 50 W
and 400 C. Dots are the experimental data and solid lines are the
simulations
J Mater Sci (2010) 45:4994–5001 4999
123
values slightly above the bulk values. This fact should
certainly contribute also to hardness and wear resistance.
Conclusions
The dependence of the physiochemical and structural
characteristics of DC reactive sputtered deposited TiC and
VC films on the reactive gas (CH4) partial pressure and on
the substrate temperature were investigated here. Elemen-
tary C/Ti and C/V concentration ratios of 1 were reached
for CH4 partial pressures around 0.5 9 10-3 mbar and
substrate temperatures around 400 C.
The phases composing the films include TiC, Ti, and C
excess, as well as TiO2 in near-surface regions of the TiC
films. On the other hand, VC, V, and C, together with V2O5
in near-surface regions, are identified in the VC films. The
increase of substrate temperature leads to a decrease of the
concentration of metallic Ti or V, with respect to TiC or
VC compounds. Metallic Ti or V eventually vanishes from
the films by increasing the substrate temperatures during
deposition, whereas C excess disappears for CH4 partial
pressures below 0.5 9 10-3 mbar.
The film densities determined here are slightly higher
than the bulk densities of the corresponding materials,
whereas the deposition rates are compatible with current
requirements for commercial production.
The experimental H3/E2 figures indicate a pronounced
wear resistance increase as the films become stoichiometric
and crystalline, while preliminary wear tests of TiC and
VC coatings of tool steel in the conditions described here
confirm this picture. In conclusion, we can say that stoi-
chiometric, crystalline, and very dense films can produce
excellent protective VC and TiC coatings concerning wear
resistance.
Acknowledgements The authors would like to acknowledge CNPq,
Capes, Fapergs for financial support.
References
1. Lee S, El-bjeirami O, Perry SS, Didziulis SV, Frantz P, Radha-
krishnan G (2000) J Vac Sci Technol B 18:69
2. Wang GB (1997) Wear 212:25
3. Fang T-H, Jian S-R, Chuu D-S (2004) Appl Surf Sci 228:365
4. Prengel HG, Pfouts WR, Santhanam AT (1998) Surf Coat
Technol 102:183
5. Singh J, Wolfe DE (2005) J Mater Sci 40:1. doi:10.1007/
s10853-005-5682-5
6. Brama M, Rhodes N, Hunt J, Ricci A, Teghil R, Migliaccio S,
Rocca CD, Leccisotti S, Lioi A, Scandurra M, De Maria G, Ferro
D, Pu F, Panzini G, Politi L, Scandurra R (2007) Biomaterials
28:595
7. Subramanian C, Strafford KN, Wilks TP, Ward LP (1996)
J Mater Process Technol 56:385
8. Hou X, Liu X, Guo M, Chou K-C (2008) J Mater Sci 43:6193.
doi:10.1007/s10853-008-2928-z
9. Shimada S, Mochidsuki K (2004) J Mater Sci 39:581. doi:
10.1023/B:JMSC.0000011514.46932.e2
10. Galvan D, Pei YT, Hosson JThM (2006) Surf Coat Technol
201:590
11. Recco AAC, Oliveira IC, Massi M, Maciel HS, Tschiptschin AP
(2007) Surf Coat Technol 202:1078
12. Soldan J, Musil J (2006) Vacuum 81:531
13. Yang S, Chang Y, Lin D, Wang D, Wu W (2008) Surf Coat
Technol 202:2176
14. Choy KL (2003) Prog Mater Sci 48:57
15. Tang J, Zabinski JS, Bulman JE (1997) Surf Coat Technol 91:69
16. Quinto DT (1996) Int J Refract Met Hard Mater 14:7
17. Rist O, Murray PT (1991) Mater Lett 10:323
18. Helmersson U, Lattemann M, Bohlmark J, Ehiasarian AP,
Gudmundsson JT (2006) Thin Solid Films 513:1
19. Portolan E, Amorim CLG, Soares GV, Aguzzoli C, Perottoni CA,
Baumvol IJR, Figueroa CA (2009) Thin Solid Films 517:6493
20. Shao N, Feng L, Mei F, Li G (2004) J Mater Sci 39:5533. doi:
10.1023/B:JMSC.0000039280.50013.91
Fig. 11 a Hardness and Young modulus and b H3/E2 ratios versus
substrate temperature for VC films deposited on Si(001). Line is only
to guide the eyes
Table 2 Mechanical properties of carbides from references [1, 7, 11]
Carbide H (GPa) E (GPa) H3/E2 (GPa)
TiC 28–35 300–500 0.1–0.4
VC 20–30 268–430 0.1–0.4
TaC 16–24 241–722 0.05–0.2
5000 J Mater Sci (2010) 45:4994–5001
123
21. Pancielejko M, Precht W, Czyzniewski A (1999) Vacuum 53:57
22. Chu WK, Mayer JW, Nicolet MA (1978) Backscattering spec-
trometry. Academic Press, New York
23. Feldman LC, Mayer JW, Picraux ST (1982) Materials analysis by
ion channeling. Academic Press, New York
24. Driemeier C, Baumvol IJR (2008) Nucl Instrum Methods Phys
Res B 266:2041
25. Ostling M, Petersson CS, Possnert G (1983) Nucl Instrum
Methods 218:439
26. Jones CM, Phillips GC, Harris RW, Beckner EH (1962) Nucl
Phys 37:1
27. Kraus W, Nolze G (2000) PowderCell for Windows Version 2.4
28. Frantz P, Didziulis SV (1998) Surf Sci 412/413:384
29. Guillot J, Chappe JM, Heintz O, Martin N, Imhoff L, Takadoum J
(2006) Acta Mater 54:3067
30. Guemmaz M, Mosser A, Parlebas J-C (2000) J Electron Spec-
trosc Relat Phenom 107:91
31. Aguzzoli C, Tentardini EK, Figueroa CA, Kwietniewski C,
Miotti L, Baumvol IJR (2009) Appl Phys A Mater Sci Process
94:263
32. Lewin E, Persson POA, Lattemann M, Stuber M, Gorgoi M,
Sandell A, Ziebert C, Schafers F, Braun W, Halbritter J, Ulrich S,
Eberhardt W, Hultman L, Siegbahn H, Svensson S, Jansson U
(2008) Surf Coat Technol 202:3563
33. Lin J, Moore JJ, Mishra B, Pinkas M, Sproul WD (2008) Thin
Solid Films 517:1131
34. Hu Y, Li L, Cai X, Chen Q, Chu PK (2007) Diamond Relat Mater
16:181
35. Choi J-G (1999) Appl Surf Sci 148:64
36. Colombi P, Agnihotri DK, Asadchikov VE, Bontempi E, Bowen
DK, Chang CH, Depero LE, Farnworth M, Fujimoto T, Gibaud
A, Jergel M, Krumrey M, Lafford TA, Lamperti A, Ma T, Matyi
RJ, Meduna M, Milita S, Sakurai K, Shabel’nikov L, Ulyanenkov
A, Van der Lees A, Wiemert C (2008) J Appl Crystallogr 41:143
37. Shackelford JF, Alexander W (2001) Materials science and
engineering handbook. CRC Press, LLC, Boca Raton
38. Ding J, Meng Y, Wen S (2000) Thin Solid Films 371:178
39. Casellas D, Caro J, Molas S, Prado JM, Valls I (2007) Acta Mater
55:4277
J Mater Sci (2010) 45:4994–5001 5001
123
ANEXO 3
1
Corrosion and nanomechanical properties of vanadium carbide thin film coatings of tool
steel
C. Aguzzolia,b,*
, C.A. Figueroaa, F.S. de Souza
c, A. Spinelli
c, I.J.R. Baumvol
a,b
a Centro de Ciências Exatas e Tecnologia, Universidade de Caxias do Sul, 95070-560 Caxias do Sul, RS, Brazil b Instituto de Física, Universidade Federal do Rio Grande do Sul, 91501-970 Porto Alegre, RS, Brazil c Departamento de Química, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC, Brazil
Abstract
The corrosion and nanomechanical characteristics of tool steel coated with vanadium
carbide thin films deposited by direct current reactive magnetron sputtering were investigated.
Cyclic polarization and electrochemical impedance spectroscopy measurements in a 3.5%
sodium chloride solution indicated that corrosion decreases as the C content and the substrate
temperature during deposition increase. The maximum hardness is reached for stoichiometric
VC coatings, decreasing for either higher or lower C contents. Complementary physico-
chemical analyses, made here or elsewhere, are used to clarify the reasons for such behavior.
The present results are discussed in terms of the optimization of the deposition parameters
aiming at concomitantly good corrosion and wear protection.
Keywords: Tool steel; Pitting corrosion; EIS; Cyclic polarization * Corresponding author. Tel.: Tel.: +55 54 32182764 Fax: +55 54 32182253. E-mail address: caguzzol@ucs.br (C. Aguzzoli)
2
1. Introduction
Group IV to VI transition metal nitrides, carbides, and carbonitrides have an unusual
combination of physicochemical properties, among them high melting temperatures, hardness
and high-temperature strength, as well as good electrical and thermal conductivity, ensuring
their use as high-temperature structural materials and/or as wear-resistant hard alloys. These
materials are also commonly used as protective hard coatings due to their mechanical, and
tribologic properties [1,2]. One important feature is the presence of structural defects, since in
these compounds bearing the NaCl-type structure, the octahedral interstitial sites of the
metallic fcc sublattice may be only partially filled with carbon or nitrogen atoms. Under
certain conditions, their presence may give rise to atomic ordering which results from the
redistribution of non-metallic atoms and structural vacancies in the interstitial lattice sites [3].
The corrosion protection of thin film physical vapor deposition (PVD) coatings is
often unsatisfactory. When exposed to an aggressive medium, local galvanic corrosion of the
substrate material is observed. Since hard layers are not very dense, the electrolyte can reach
the steel substrate through pores and microcracks. A galvanic couple is formed, the compound
coating being electrochemically the noblest partner. As a consequence, the steel substrate will
begin to dissolve anodically [4]. In addition, the microstructure of PVD coatings is
characterized by a columnar microstructure and corrosion problems in applications are
generally attributed to the voids between these columns, to pinholes, and to eventually
existing cracks [4]. Furthermore, nitrides and other coatings operating at higher temperatures
are prone to be oxidized, forming TiO2, Al2O3, Cr2O3, and mixed oxides. These oxide layers
generally control the kinetics of the oxidation at higher temperatures and may also close the
above mentioned coating defects. More specifically, ceramic coatings, in particular, usually
contain numerous small defects, like pinholes, which may penetrate the whole coating
thickness and lead to rapid galvanic corrosion when subjected to a corrosive atmosphere [5,6].
3
Furthermore, ceramic coatings may crack in service owing to substrate plastic deformation
when subjected to high intensity loading or impact loading, which will cause rapid crevice
corrosion Therefore, local corrosion may cause an accelerated degradation of the metallic
substrate [7,8].
In vanadium carbide (VC) films, the carbon content has a strong influence on the
cristallinity and on the mechanical properties, especially on hardness [9]. The substrate
temperature during deposition (herein called deposition temperature) also has an important
influence on these properties. The tribologic properties, like wear and friction coefficient of
VC are also superior, a fact that has been attributed to the extremely fine grain dispersion of
thin film coatings [10].
VC coatings [11,12] show some other distinguishing properties in cutting tool
applications. For example, V2O5 as a solid lubricant forming on the coating surface in the
machining process, improves the wear resistance of cutters [13,14]. It was reported by Ferro
et al. [11] that the electron beam deposited cubic VC coating from a carbide target reaches a
high hardness of 25 GPa. In the research of Aouni et al. [15], a series of VC coatings with
different carbon contents were prepared by reactive dc diode magnetron sputtering from a
vanadium target in an Ar–CH4 mixture. It was found that varying the partial pressure of CH4
(3% ~ 15.7% of the mixture), monophase or multiphase coatings like vanadium solid solution,
V2C, VC and VC + C were obtained due to different carbon contents. Unfortunately, the
corresponding mechanical and tribological properties were not reported in their paper [16].
In order to make VC films more widely used as protective coatings, investigation of
the corrosion, mechanical, and tribologic properties should be performed. There are in the
literature some studies on VC coatings which provide substantial information about
mechanical and physicochemical properties. However, we could not find reports on the
corrosion behavior, although this is an important feature to design a new protective coating,
4
especially in applications that involve contact with gases or liquids from the productive
process, such as machining or die.
Considering that we could not find in the literature corrosion investigations of VC
coatings of steel, the present work is undertaken in order to determine, in samples prepared in
identical conditions, the corrosion behavior and the nanomechanical properties of AISI H12
tool steel coated with VC films deposited by direct current (DC) reactive magnetron
sputtering. Different gas compositions and deposition temperatures were accessed in order to
investigate the influence of these deposition parameters on the above mentioned properties.
Complementary physico-chemical analyses, made here or elsewhere, were used to better
clarify the observed facts. The results are discussed concerning the optimization of the
deposition parameters aiming at concomitant protection against corrosion and wear.
2. Experimental
VC thin films, 200 nm thick, were deposited on AISI H12 tool steel, single-crystalline
silicon (001) wafers, and amorphous carbon by DC reactive magnetron sputtering from a pure
V target, using an Ar-CH4 gas mixture. The samples deposited on AISI H12 steel (0.3 C, 0.2
Mn, 0.8 Si, 4.75 Cr, 0.3 Ni, 1.25Mo, 1.0 W, 0.5 V, 0.25 Cu) were used for corrosion tests,
whereas deposition on C substrate was used for Rutherford backscattering spectrometry
(RBS) [17] analysis. Deposition on Si(001) substrate was used for all other analysis and tests.
Prior to deposition, substrates were cleaned by ultrasonic acetone bath and immediately
loaded in the sputtering vacuum chamber. The total gas pressure during deposition ranged
from 0.3 to 0.6 Pa with a power density of 5.5 W cm-2 in the target. The deposition
temperature was varied from 20 to 500 °C.
The elementary composition of the films was determined by RBS of He+ ions incident
at 2 MeV, backscattering detection angle of 165°, bearing a sensitivity of 1014 atoms cm−2
(about 1/10 of a monolayer) with 5% accuracy for V and over 10% accuracy for C [18]. The
5
method also allows the determination of film thickness, assuming the nominal bulk density of
the materials composing the films, namely 5.77 g cm-3 for VC. The areal densities of V and C
were determined using a standard of Bi-implanted Si.
The poor accuracy in C quantification by RBS comes from the overlap of substrate-C
and film-C [24]. In order to reduce the experimental error in C quantification, the 12C(α,α)12C
resonant scattering at 4.26 MeV [19,20,21] was used, taking advantage of its selectivity for C,
as well as the relatively high cross section of this resonance, which is also narrow enough in
energy to allow for C profiling [19,20,21] in the films. This method increases the C signal-to-
noise ratio by at least a factor of ten as compared to RBS, thus improving significantly the
accuracy of the C quantification. A SiC(0001) single crystalline wafer was used here as a
standard for C quantification. Summarizing, V quantification was performed with RBS and C
quantification with resonant nuclear reaction analysis (NRA).
Glancing angle X-ray diffraction (GAXRD) analyses were performed using a
Shimadzu XRD-6000 apparatus, with Cu Kα radiation (λ = 1.5418 Å) at an incidence angle of
2°, in order to determine the crystalline structure of the films. The film densities were
determined by X-ray reflectometry (XRR) using Cu Kα radiation and scanning in 0.002°
steps. XRR data were simulated using the Parratt formalism for reflectivity [22]. The XRR
analyses were also used to correct the calculus of thickness of the deposited films.
The hardness and reduced elastic modulus were accessed by the nanoindentation
technique using a model 600 – Micromaterials Nanotest with a Berkovich diamond indenter, a
load rate of 0.04 mN s-1 and a maximum indentation depth of 40 nm.
Raman spectroscopy was performed in air at room temperature with a ND-MDT
Ntegra-Spectra System equipped with a solid state laser (λ=473 nm).
The electrochemical measurements, including impedance, were carried out with a
Voltalab 10, model PGZ 100 Radiometer Copenhagen potentiostat/galvanostat interfaced with
6
a microcomputer using the VoltaMaster 4.0 software for data acquisition and analysis. The
corrosive medium was in aerated 3.5% NaCl solution. A double-walled glass three-electrode
cell was used to carry out the corrosion tests. The working electrode was a 0.55 cm2
(geometrical surface area) AISI H12 tool steel disc mounted in a glass tube with Araldite®
epoxy. Prior to the corrosion tests, the electrode surface was degreased with acetone, rinsed
with deionized water, and gently dried with nitrogen. The auxiliary electrode was a graphite
rod and the reference electrode was a saturated calomel electrode (SCE) connected to the cell
by a bridge and a Luggin–Haber capillary. All potentials are quoted versus this reference
electrode. Cyclic potentiodynamic polarization curves were recorded according to the ASTM
G61 standard [23], which is recommended for evaluating the pitting corrosion tendency of
materials in chloride-containing media. In this pitting experiment, the open circuit potential
(EOCP) was initially measured over 30 min. The potential scan was then started from the EOCP-
value in the positive direction until a threshold current density around of 5.0 mA cm-2 was
reached. At this point, the potentiodynamic scan was reversed to the negative direction, and
continued down to the EOCP. The pitting potential (Epit) was taken as the value at which the
current sharply increased during the positive scan. The potential where the loop closed on the
reverse scan was taken as the protection potential (Epro) at a scan rate of 1 mV/s. The values
reported here correspond to averages of three measurements, and exhibit standard deviations
of 2–15 mV. Electrochemical impedance spectroscopy (EIS) was carried out at the open-
circuit potential in the frequency range 100 kHz – 100 mHz with a 10 mV amplitude sine
wave. Scanning Electron Microscopy (SEM) analyses were performed using a Shimadzu
SSX-550 for evaluating the surface after the corrosion test.
3. Results and discussion
3.1. Composition
7
Figure 1 shows the composition ([C]/[V]) of the films (herein called C/V) for different
partial pressures of methane during deposition. The figure also shows the methane content of
the gas mixture (Ar-CH4) introduced in the chamber during the deposition process. The C
content in the films increased linearly with the increasing of methane partial pressure. As
shown in Reference [24], the film thickness depends linearly on time, at fixed deposition
temperature and CH4 concentration. On the other hand, the thickness is essentially constant in
the whole deposition temperature interval used here, at fixed deposition time and CH4
concentration. This is shown in Reference [9] for 15% CH4 and confirmed here for 24 and
33% (not shown). The present analyses revealed that the thickness is also essentially constant
in the whole CH4 concentration range used here, at fixed time and deposition temperature.
With these data on hands, deposition time was always adjusted to provide samples with a
constant thickness of 200 nm.
3.2. Corrosion behavior
In order to investigate the influence of film composition on the pitting corrosion, cyclic
polarization experiments were carried out with AISI H12 uncoated and coated with VC films
with different C/V ratios. Some representative results are shown in Fig. 2a. The EOCP-, Epit-
and Epro-values were determined as described in the Experimental section, being collected in
Table I. The EOCP-value is strongly influenced [25] by the morphology and nature of the
film/solution interface, as well as by the structure, thickness and chemical composition of the
protective films. The EOCP-values measured after 30 min of exposure to a 3.5% NaCl solution
shifted toward more positive values as the C/V ratio increased in VC films deposited at 20 °C.
This indicates that the VC films with higher C/V ratios provide higher corrosion protection to
AISI H12 steel in 3.5% NaCl solution. In addition, the cyclic polarization curves shown in
Fig. 2a are typical of materials in the passive state with critical Epit. The Epit-values increased
8
for increasing C/V ratios, meaning that the pitting formation tendency is reduced for
increasing C/V ratios. Furthermore, the loop in the E versus j closed in the reverse scan, i.e.,
the Epro is more negative than Epit, indicating that repassivation occurs. Finally, the size of the
pitting loop decreased as the C/V ratio increased.
Surface properties, electrode kinetics and corrosion mechanisms can also be obtained
from EIS experiments. Fig. 2b shows the Nyquist plot obtained at open-circuit potential for
samples with the same composition as in Fig. 2a. For the uncoated AISI H12 steel electrode, a
depressed charge transfer semicircle is observed at high frequencies, which is attributed to the
constant time of the charge transfer and double-layer capacitance [26,27]. The intersection of
this semicircle with the real axis at high frequencies gives the ohmic resistance of the solution
enclosed between the working electrode and the tip of the salt bridge containing the reference
electrode. At low frequencies, a charge transfer resistance of 0.75 kΩ cm2 was found from the
difference in impedances at lower and higher frequencies. For the coated electrodes with
different C/V ratios, the impedance diagrams are analogous to that observed for the uncoated
electrode, indicating that the corrosion is mainly controlled by a charge transfer process.
Deviations from a perfect circular shape indicate frequency dispersion of interfacial
impedance arising from a lack of homogeneity of the electrode surface due to film roughness.
It is worth noting that the impedance increases with the C/V ratio, up to 3.27 kΩ cm2 for
C/V=2.5. Thus, we are probably in the presence of a first corrosion protection mechanism,
whereby a higher concentration of carbon inhibits the flow of charge through the coating. This
mechanism will be detailed in the rest of this section.
Similar results were obtained when the deposition temperature was varied as shown in
Fig. 3, at constant C/V ratio of 2.5. In other words, the corrosion process decreased as the
deposition temperature increased. These results are in agreement with the data previously
reported for the corrosion behavior of pulsed plasma-nitrided AISI H13 tool steel in 0.9%
9
NaCl solution [25] and for sintered-plasma nitrided steels containing different alloying
elements in 1.25 mol L-1 KNO3 supporting electrolyte [28]. The increase of the corrosion
resistance for higher deposition temperatures could be also associated with the increase of the
coating densities. In order to investigate this aspect, the film densities were determined by
XRR. Typical curves are given in Fig. 4 and the results indicate a 13% increase in density for
films deposited at 400 oC as compared to those deposited at 20 oC. Both factors, more
compact (higher density) coatings and higher carbon concentration above stoichiometry, may
constitute diffusion barriers for the flow of charge through the coating.
The efficiency of the corrosion protection (P) for C/V=2.5 was estimated using the
formula [29]:
P = 1 - (j1/j2) x 100 (1)
where j1 is the corrosion current density of the substrate and j2 is the corrosion current density
of the substrate + coating. The result was an efficiency of 80% for the best case of the present
work.
In Figure 5a it is shown a SEM image of a sample deposited with C/V=2.5 after
corrosion. Figure 5b shows typical pits, where we can see the substrate in the bottom of the
pits exposed by the corrosion process. According to the shape of the EIS curves, one can
foresee open or closed pits [30]. The present EIS results indicate that the morphology of the
pits is of the open kind. Indeed, the morphology of the here observed pits is consistent with
this corrosion mechanism.
3.3. Mechanical properties
Typical nanoidentation curves are shown in Figure 6, for C/V = 2.5 and deposition
temperatures of 100, 300, and 500 0C. Each calculated hardness is an average over twenty
different nanoidentation curves of the same sample, being extracted according to the Oliver-
10
Pharr method [31]. Figure 7a shows the influence of composition on hardness (H) and Young
modulus (E). The hardness increases abruptly as C/V approaches unity and then it decreases
more slowly for C/V > 1. This is in perfect agreement with the literature [16,3]. The Young
modulus was calculated with a Poisson ratio of 0.25 [32]. We recall here that the indentation
depth in these measurements was limited to 40 nm, such that only the film hardness and
Young modulus were accessed.
Figure 7b shows the influence of temperature on H and E in films with C/V=2.5. We
observed that the films have a slight increase of hardness and Young modulus with deposition
temperature, probably because of increasing density, as discussed above. The measured
Young modulus is significantly lower than previous results for comparable hardness
[16,32,33].
The wear resistance of the present coatings can be estimated using the elastic strain to
failure (H/E) criterion, which has been proposed and consistently used to evaluate the
resistance to plastic deformation of thin film coatings and to predict their resistance to wear
[34]. Indeed, a higher H3/E2 ratio indicates a high resistance of the coating to plastic
deformation and, presumably, a high wear resistance as well, besides of low stiffness [35,36].
Figure 7c shows the variation of the H3/E2 ratio with the C/V ratio. The highest value of the
H3/E2 ratio falls around C/V = 1.2. The H3/E2 ratios for VC films obtained here are
comparable to Ti-B-N and SiC films [37,38,39].
3.4. Amorphous carbon in the films
Figure 8 shows Raman scattering spectra for a stoichiometric VC film deposited on
Si(001) and for films with C/V larger than one. These Raman spectra can be deconvoluted
into two Gaussian peaks (bands) plus a linear background. The peak around 1350 cm-1 is
assigned to a disorder-induced band (D-band), whereas that around 1582 cm-1 is assigned to
graphite band (G-band) [40]. The intensity ratio ID/IG represents the amount of defects inside
11
the carbon material and the atomic bonding structure. Here, all films with C/V larger than one
have the same (ID/IG) ratio, which means that an increase in ID (disorder), owing to an
increase in the proportion of overstoichiometric C, is accompanied by a proportional increase
in IG (graphitic or amorphous carbon). In other words, one can say that all the increase of
disorder in the films comes from the increase of amorphous carbon. In the whole infrared
spectrum there are no peaks that could be associated with crystalline VC. The film with
C/V=1 did not show any evidence of having amorphous carbon.
Furthermore, the overstoichiometric carbon existing in the VC coatings consist of
amorphous carbon mostly in small aromatic clusters, a few nanometer in size [41] and of
carbon in solution in the VC matrix. Thus, corrosion due to pathways in the columnar
structure of the VC network can be due to blocking by the nanoclusters inserted therein [16].
Alternatively, carbon nanoclusters in solid solution in the VC network can fulfill the pinholes
or act as diffusion barriers for the transport of corrosive species.
Finally, according to previous and the present results, the hardness and Young modulus
measured in films with C/V > 1 are lower than that for stoichiometric films due to the
amorphous carbon clusters present in the VC network since amorphous carbon clusters can
only create regions of lower hardness in the VC matrix. On the other hand hardness and
Young modulus measured in films with C/V < 1 are lower than for C/V=1 due to the excess
of V.
3.5. Crystallographic structure
Stoychiometric VC is an interstitial compound, where vanadium forms the principal
lattice and carbon occupies the octahedral interstitial sites [42], although many other different
phases coexist. In particular, the crystalline structure of VCx thin films has been reported [15].
Furthermore, it was shown that during deposition, C can also occupy metastable, interstitial
tetrahedral sites, from where it may migrate to the stable octahedral sites [9,24].
12
Figure 9a shows the grazing-angle diffractograms for two different compositions of
VC thin films, C/V=1 and C/V=2.5 deposited at 20 oC. The (111) and (200) planes of VC
with an fcc-like structure intersect tetrahedral and octahedral interstitial sites, respectively. In
previous work [9] we observed that the intensity ratio I111/I200 decreases with the increase of
the C/V ratio in the films. Thus, the improved corrosion protection of the VC films here may
be also due to carbon migration from tetrahedral to octahedral interstitial sites at higher
temperatures, which decreases the availability of the more reactive carbon in tetrahedral
interstitial positions [9].
Figure 9b shows that VC films with C/V=2.5 deposited at 400 oC have a similar
carbon interstitial distribution as that shown in Fig. 9a for C/V=1 at 20 oC (see Fig.9a). It is
important to remark that the low intensity of the diffraction peaks for planes (111) and (200)
appearing in Fig. 9b for deposition at 400 oC is due to the presence of carbon nanoclusters.
The sample diffractogram for deposition at 20 oC in Fig. 9b is similar to the corresponding
one in Fig. 9a. Moreover, deposition at lower temperatures and segregated carbon
nanoclusters can induce VC films with preferential orientation. In fact, carbon nanoclusters in
diamond-like coatings introduce compressive residual stress in the film [41]. Although such
carbon nanoclusters in the VC network seem to produce preferential orientation, by increasing
deposition temperature up to 400 oC one can relax the compressive stress of VC films with
C/V=2.5. A final evidence for preferential orientation is given in Fig. 9c, where the sample of
Fig. 9b (20 °C and C/V=2.5) was rotated by 90° in GAXRD analyses, leading to the
disappearing of the (200) peak and therefore clearly indicating the preferential orientation of
the films.
4. Conclusions
In summary, we investigated the corrosion behavior, the structure, and the
nanomechanical and tribolologic properties of VC thin film coatings bearing different C/V
13
ratios, deposited on AISI H12 steel by DC reactive sputtering at different substrate
temperatures during deposition.
The corrosion protection efficiency of the coated steel increased with the increase of
the C/V ratio, reaching 80% as compared to the uncoated steel. The pitting formation
tendency is also reduced as C/V increases. This is probably due to the higher concentration of
amorphous carbon nanoclusters occupying voids in the columnar microstructure and thus
reducing the flow of charge through the coating. In addition, corrosion may also be inhibited
by carbon migration from tetrahedral to octahedral interstitial sites at higher temperatures,
decreasing the availability of the more reactive carbon in tetrahedral interstitial positions The
cyclic polarization curves indicate the occurrence of repassivation in the corrosion tests.
Electrochemical impedance spectroscopy shows that corrosion here is mainly controlled by a
charge transfer process. The shapes of the electrochemical impedance spectroscopy curves
point out to open pits, which correspond to the morphology observed by scanning electron
microscopy.
The influence of the deposition temperature was also studied. The best results for
corrosion protection were found at 400 °C, probably due to more dense coatings than at lower
temperatures.
The hardness of the coatings increased abruptly as C/V approaches unity and then
decrease more slowly for C/V > 1. The Young modulus, on the other hand, increases slowly
as the C/V ratio increases, reaching a maximum around C/V = 1.5. The H3/E2 ratio, that
serves here to foresee the wear behavior of the coated steel, also increased with the increase of
the C/V ratio, reaching a maximum at C/V = 1.2.
The present results point out to the possibility of optimizing VC coatings in order to
improve concomitantly the corrosion and the wear resistance of the coated steel. This can be
done by controlling the film density, through the control of the deposition temperature, the
14
composition of the coatings or, alternatively, by using multilayered or graded composition
coatings to obtain the desired VC coating properties for a particular application. Further
research is in progress in these directions.
Acknowledgements
The authors would like to acknowledge the INCT “Surface Engineering” of MCT/CNPq-Brazil and Capes for financial support. IJRB, CAF, and AS are CNPq fellows. CAF is CAPES fellow.
References
[1] T-H. Fang, S-R. Jian, D-S. Chuu, Appl. Surf. Sci. 228 (2004) 365-372. [2] H.G. Prengel, W.R. Pfouts, A.T. Santhanam, Surf. Coat. Technol. 102 (1998) 183-190. [3] V.N. Lipatnikov, W. Lengauer, P. Ettmayer, E. Keil, G. Groboth, E. Kny, J. Alloys Compd. 261 (1997) 192-197. [4] W. Brandl, C. Gendig, Thin Solid Films 290-291 (1996) 343-347. [5] H. Dong, Y. Sun, T. Bell, Surf. Coat. Technol. 90 (1997) 91-101. [6] K.P. Purushotham, L.P. Ward, N. Brack, P.J. Pigram, P. Evans, H. Noorman, R.R. Manory, Corros. Sci. 50 (2008) 8-14. [7] S. Rudenja, C. Leygraf, J. Pan, P. Kulu, E. Talimets, V. Mikli, Surf. Coat. Technol. 114 (1999) 129–136. [8] B. Subramanian, R. Ananthakumar, M. Jayachandran, Surf. Coat. Technol. 205 (2011) 3485–3492. [9] E. Portolan, C.L.G. Amorim, G.V. Soares, C. Aguzzoli, C.A. Perottoni, I.J.R. Baumvol, C.A. Figueroa, Thin Solid Films 517 (2009) 6493-6496. [10] S. Lee, O. El-bjeirami, S.S. Perry, S.V. Didziulis, P. Frantz, G. Radhakrishnan, J. Vac. Sci. Technol. B 18 (2000) 69-75. [11] D. Ferro, J.V. Rau, A. Generosi, V.R. Albertini, A. Latini, S.M. Barinov, Surf. Coat. Technol. 202 (2008) 2162-2168. [12] B. Chicco, W.E. Borbidge, E. Summerville, Mater. Sci. Eng. A 266 (1999) 62-72. [13] M. Woydt, A. Skopp, I. Dörfel, K. Witke, Wear 218 (1998) 84-95. [14] J.G. Chen, C.M. Kim, B. Frühberger, B.D. DeVries, M.S. Touvelle, Surf. Sci. 321 (1994) 145-155. [15] A. Aouni, P. Weisbecker, T.H. Loi, E. Bauer-Grosse, Thin Solid Films 469-470 (2004) 315-321. [16] X. Wu, G. Li, Y. Chen, G. Li, Int. J. Refract. Met. Hard Mater. 27 (2009) 611-614. [17] W.K. Chu, J.W. Mayer, M.A. Nicolet, Backscattering Spectrometry, Academic Press, New York, 1978. [18] L.C. Feldman, J.W. Mayer, S. T. Picraux, Materials Analysis by Ion Channeling, Academic, New York, 1982. [19] C. Driemeier, I.J.R. Baumvol, Nucl. Instrum. Methods Phys. Res., Sect. B 266 (2008) 2041-2046. [20] M. Östling, C.S. Petersson, G. Possnert, Nucl. Instr. and Meth. 218 (1983) 439-444.
15
[21] C. Miller Jones, G.C. Phillips, R.W. Harris, E.H. Beckner, Nucl. Phys. 37 (1962) 1-22. [22] L.G. Parratt, Phys. Rev. 95 (1954) 359-369. [23] ASTM G 61-86, Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys, ASTM, 2009. [24] C. Aguzzoli, C.A. Figueroa, G.V. Soares, I.J.R. Baumvol, J. Mater. Sci. 45 (2010) 4994-5001. [25] R.L.O. Basso, H.O. Pastore, V. Schmidt, I.J.R. Baumvol, S.A.C. Abarca, F.S. de Souza, A. Spinelli, C.A. Figueroa, C. Giacomelli, Corros. Sci. 52 (2010) 3133-3139. [26] W.J. Lorenz, F. Mansfeld, Corros. Sci. 21 (1981) 647–672. [27] O.E. Barcia, O.R. Mattos, N. Pebere, B. Tribollet, J. Electrochem. Soc. 140 (1993) 2825-2832. [28] N.C. Pereira, F.G. Mittelstadt, A. Spinelli, C.V. Franco, A.M. Maliska, A.N. Klein, J.L.R. Muzart, J. Mat. Sci. 30 (1995) 4817-4822. [29] F.S. de Souza, A. Spinelli, Corros. Sci. 51 (2009) 642-649. [30] F. Wenger, S. Cheriet, B. Talhiy, J. Galland, Corros. Sci. 39 (1997) 1239-1252. [31] W.C. Oliver, G.M. Pharr, J. Mater. Res. 7 (1992) 1564-1583. [32] X-G. Lu, M. Selleby, B. Sundman, Acta Mater. 55 (2007) 1215-1226. [33] C. Kral, W. Lengauer, D. Rafaja, P. Ettmayer, J. Alloys Compd. 265 (1998) 215-233. [34] A. Leyland, A. Matthews, Wear 246 (2000) 1-11. [35] J. Soldán, J. Musil, Vacuum 81 (2006) 531-538. [36] S-M. Yang, Y-Y. Chang, D-Y. Lin, D-Y. Wang, W. Wu, Surf. Coat. Technol. 202 (2008) 2176-2181. [37] D.V. Shtansky, S.A. Kulinich, E.A. Levashov, A.N. Sheveiko, F.V. Kiriuhancev, J.J. Moore, Thin Solid Films 420-421 (2002) 330-337. [38] Y-Y. Chang, S-J. Yang, W. Wu, Y-C. Kuo, J-W. Lee, C-J. Wang, Thin Solid Films 517 (2009) 4934-4937. [39] A. Soum-Glaude, L. Thomas, E. Tomasella, Surf. Coat. Technol. 200 (2006) 6425-6429. [40] W.S. Kim, H. Oki, A. Kinoshita, K. Murakami, S. Abo, F. Wakaya, M. Takai, J. Vac. Sci. Technol. B 26 (2008) 760-763. [41] J. Schwan, S. Ulrich, V. Batori, H. Ehrhardt, S.R.P. Silva, J. Appl. Phys. 80 (1996) 440-447. [42] V.N. Lipatnikov, A.I. Gusev, P. Ettmayer, W. Lengauer, J. Phys.: Condens. Matter 11 (1999) 163-184.
16
Table captions
Table I – Relevant corrosion potentials for AISI H12 steel samples coated with VC
films of different compositions in 3.5% NaCl solution.
Sample EOCP
(mV/SCE) Epit
(mV/SCE) Epro
(mV/SCE) AISI H12 – 628 – 496 – 663 C/V=0.7 – 621 – 487 – 673 C/V=1.0 – 589 – 444 – 688 C/V=1.6 – 570 – 417 – 662 C/V=2.5 – 531 – 414 – 649
17
Figure captions
Figure 1 – C/V ratios for the films deposited at 400 oC at different methane partial pressures. Figure 2 – (a) Cyclic polarization curves and (b) Nyquist plots for AISI H12 tool steel samples coated with VC films at 20 °C with different C/V ratios in 3.5% NaCl solution. Figure 3 – (a) Cyclic polarization curves and (b) Nyquist plots for AISI H12 tool steel samples coated with VC films of constant C/V ratio of 2.5, deposited at different substrate temperatures in 3.5% NaCl solution. Figure 4 – X-ray reflectometry data (solid circles) from CV films deposited on Si at 20 °C and 400 ºC and the corresponding simulation (solid line). The density (in g cm−3) of the films obtained from the simulations is presented near each curve. Figure 5 – Scanning electron microscopy of a AISI H12 tool steel sample coated with a 200 nm thick VC film, after corrosion in 3.5% NaCl solution. The images show the pits (a) and the details of one pit with the exposed substrate in the bottom (b). Figure 6 – Indentation curves of VC thin film with C/V = 2.5, deposited at different temperatures.
Figure 7 – Hardness and Young modulus of (a) VC thin films with different compositions, deposited at 400 °C, (b) VC thin films with different deposition temperatures, and (c) H3/E2 ratios for different C/V at 400 °C deposition temperature. The lines are only to guide the eyes. Figure 8 – Raman scattering spectra for VC films with different compositions deposited at 20 oC. Figure 9 – Glancing angle X-ray diffractograms from VC films for (a) two different compositions, deposited at 20 °C, (b) two different deposition temperatures of substrate and same film composition (C/V=2.5), and (c) for the film C/V=2.5 from (a) and for the same film rotated by 900.
18
Figure 1
19
Figure 2
20
Figure 3
21
Figure 4
22
Figure 5
23
Figure 6
24
Figure 7
25
Figure 8
26
Figure 9
ANEXO 4
Physicochemical, structural, and mechanical properties of Si3N4 filmsannealed in O2
C. Aguzzoli,1,2 C. Marin,1 C. A. Figueroa,1 G. V. Soares,1,a and I. J. R. Baumvol1,2
1Universidade de Caxias do Sul, Caxias do Sul, Rio Grande do Sul 95070-560, Brazil2Instituto de Física, UFRGS, Porto Alegre, Rio Grande do Sul 91509-900, Brazil
Received 13 December 2009; accepted 6 February 2010; published online 14 April 2010
The physicochemical, structural, and mechanical properties of silicon nitride films deposited byradio frequency reactive magnetron sputtering were investigated before and after thermal annealingin 18O2. As-deposited films were essentially amorphous, stoichiometric, and free from contaminantsfor a wide range of deposition parameters, with hardness figures ranging from 16.5–22 GPa,depending mainly on the deposition temperature. After 18O2 annealing at 1000 °C, films hardnessconverged to 21 GPa, independently of the deposition temperature, which is explained based on thecrystallization of the films at this annealing temperature. Moreover, oxygen is incorporated only in7.5 nm of the Si3N4, forming silicon oxynitride at the top surface of the film, indicating a goodoxidation resistance at high temperature. Finally, the elastic strain to failure H3 /E2, which mimicsthe wear resistance of the film, doubles after the 1000 °C annealing. These observations show thegreat potential of silicon nitride as a hard coating for high temperature applications.© 2010 American Institute of Physics. doi:10.1063/1.3359655
I. INTRODUCTION
There is currently a crescent search for materials andsurface coatings bearing high hardness and sufficient tough-ness at high temperatures. This is mostly concerned withtools for dry machining, cutting, and drilling, as well as diesfor molten metal injection, and other applications.1–3 Drymachining technology is ecologically and economically im-portant, since the use, maintenance, and disposal of coolantlubricants entail enormous costs. Indeed, investigations showthat in some cases the costs for using a coolant lubricant aremany times higher than, for example, the tool costs.4 Thus,coatings for cutting tools retaining combined hard and lubri-cating properties at high temperatures seem to be very inter-esting alternatives to reduce the enormous amounts of cool-ing emulsion and to work with minimal or no lubricant in anumber of applications.4,5 Moreover, energy generation re-lated issues also demand coating for high temperatures ap-plications, especially with high oxidation and corrosion re-sistance. For instance, to accomplish the next generation ofcoal power plants combustion engines in integrated gasifica-tion combined-cycle with 50% efficiency and zero emis-sions, they must operate at temperatures as high as1400 °C.6 In this way, the hot section of the turbine willrequire coatings to fulfill these new demands. New nuclearfission and fusion technologies will also require coatingswith oxidation and corrosion resistance properties in extremeoperation conditions.
The drawbacks of the well known Ti-based coatingshave strongly limited their applications at high temperatures.This results in a challenge, since most high temperature coat-ings rely on the formation of a protective oxide scale byinteraction with the environment. This scale must fulfill sev-eral requirements, like being stable, dense, and adherent,
growing slowly, besides of bearing high temperature hard-ness, low friction coefficient, and wear and corrosion resis-tance. These conditions are in general not fulfilled by Ti-based coatings above 800 °C. However, in dry machiningthe cutting tool edge may reach well above 800 °C,7 a tem-perature at which most of the Ti-based coatings degrade dueto oxidation, corrosion, and formation of a porous, nonpro-tective oxide scale. New coatings are being developed forhigh temperature applications, such as AlCrN, WC/C, as wellas several multilayered coatings.1–3,8,9
Silicon nitride is a promising coating candidate for hightemperature tools, die coatings, and other engineering com-ponents owing to its reasonably high hardness, combinedwith thermodynamical stability, corrosion resistance, andoxidation resistance at the high temperatures addressed.10–13
Since most of the hard coatings investigated so far loosesubstantially their hardness when submitted to high tempera-tures, either at work or in laboratory furnace heating, it isvery useful to know whether the hardness and elastic modu-lus of silicon nitride coatings would be retained up to tem-peratures of practical interest, such as 1000 °C. Another as-pect of major interest for practical purposes would be thethickness, composition, and adherence of any eventual oxideor oxynitride layer formed due to high temperature process-ing that can act as a protective and lubricant layer near thesilicon nitride film surface. Previous studies of silicon oxyni-tride films showed that hardness and Young modulus in-creased with increasing nitrogen content14 from SiO2 toSi3N4. Furthermore, the existence of Si–N bonds embeddedin Si–O matrix tended to enhance these magnitudes, ap-proaching the values of silicon nitride.15,16
Many deposition techniques have been used to depositSi3N4 films, such as chemical vapor deposition CVD,plasma enhanced CVD, and magnetron sputtering.17 Amongthem, deposition by magnetron sputtering can lead to severalaElectronic mail: gvsoares@gmail.com.
JOURNAL OF APPLIED PHYSICS 107, 073521 2010
0021-8979/2010/1077/073521/9/$30.00 © 2010 American Institute of Physics107, 073521-1
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
advantages, such as: a low substrate temperature duringdeposition, since in the CVD process deposition tempera-tures can be as high as 800 °C, b wide acceptance by theindustrial sector, making it easy to scale up the process, celimination of hydrogen in the films, since hydrogenated sili-con nitride films present inferior thermal stability,18 and delimination of toxic gases in the deposition process, such asNH3 and SiH4.
Mechanical properties of Si3N4 thin films at high tem-perature have not been found in the literature by the presentauthors. However, thermal stability has been addressed,11
showing that even for temperatures far above 1000 °C andrather long annealing times, the amorphous as-depositedfilms are transformed in a mixture of the stable -Si3N4 andthe metastable -Si3N4 phases.
Finally, the hardness to Young modulus H/E ratio, socalled elastic strain to failure, has been proposed and consis-tently used to evaluate the resistance to plastic deformationof thin film coatings.19–22 More specifically, the H3 /E2 ratiois considered to be a good indicator of the coating resistanceto wear. Thus, a high H3 /E2 indicates a high resistance of thecoating to plastic deformation and, presumably, a high wearresistance as well, besides of low stiffness.23,24 Therefore, thetemperature dependence of H3 /E2 is also determined here forthe Si3N4 films.
In the present work we investigated the physicochemi-cal, mechanical, and structural properties of the Si3N4 filmsdeposited on Si by radio frequency rf reactive magnetronsputtering, before and after annealing in oxygen.
II. EXPERIMENTAL
Silicon nitride Si3N4 films were deposited on Si001and on amorphous carbon substrates by rf reactive magne-tron sputtering. Prior to deposition, substrates were cleanedby ultrasonic acetone bath and immediately loaded in thesputtering vacuum chamber, which was pumped down to abase pressure of 510−7 mbar. Silicon substrates were sub-mitted to an additional cleaning step in 10% hydrofluoridricacid solution, after the ultrasonic acetone bath. A 2 in. highpurity 99.99% silicon target was used, located 60 mmaway from the substrate of interest, and Si3N4 film deposi-tions were performed using a mixture of argon and nitrogengases, with a constant argon partial pressure of 310−3 mbar and a variable N2 partial pressure. An input rfpower density of 7.7 W cm−2 was employed with a reflectedpower density lower than 0.05 W cm−2. The substrate tem-perature was varied from room temperature 23 °C to
500 °C. No substrate bias was applied and no delaminationof the films was observed in all cases. Table I summarizesthe deposition parameters.
In order to investigate the thermal stability and oxidationresistance of the as-deposited Si3N4 coatings, samples wereloaded in a static pressure resistively heated quartz furnace,which was pumped down to 210−7 mbar, before beingpressurized with oxygen enriched to 97% in the isotope ofmass 18, hereafter called 18O2 annealing. Annealing was per-formed in 100 mbar of 18O2 for 1 h, at three different tem-peratures, namely, 250, 500, and 1000 °C. The use of the18O rare isotope allows us to distinguish it from oxygen pre-vious incorporated in the films due to contamination or dueto atmospheric air exposure.
The elementary composition of the films was evaluatedby Rutherford backscattering spectrometry RBS using a 2MeV He+ beam and a backscattering detection angle of 165°,bearing a sensitivity of 1014 atm cm−2 about 1/10 of amonolayer and 10% accuracy.25 The crystalline structure ofthe films was determined by grazing incidence angle x-raydiffraction GAXRD using a constant incident angle of 1°and Cu K radiation =1.5418 Å. Film densities were ob-tained from x-ray reflectometry XRR measurements usingCu K radiation and scanning in 0.002° steps. XRR datawere simulated using the Parratt formalism for reflectivity.26
The hardness and reduced elastic modulus were accessed bythe nanoindentation technique with a Berkovich indenter, aload rate of 0.03 mN s−1 and a maximum indentation depthof 20 nm. 18O and 15N profiles were determined by narrownuclear resonant reaction profiling27 NRP using the narrowresonances =100 and 120 eV in the cross section curvesof the 18Op,15N and 15Np,12C nuclear reactions at151 keV and 429 keV, respectively. Simulations of thenuclear reaction excitation curves were carried out using theFLATUS code.28 Although 14N is the most abundant nitrogenisotope 99.6%, the NRP technique is sensitive enough toprofile the 15N isotope present in the Si3N4 films, with anatural abundance of 0.4%. X-ray photoelectron spectros-copy XPS was performed using Mg K radiation 1253.6eV at a take-off angle of 60° in order to evaluate the Si andN chemical environments.
III. COMPOSITION, STRUCTURE, AND MECHANICALPROPERTIES OF THE AS-DEPOSITED SI3N4FILMS
Figure 1a shows a typical RBS spectrum of a Si3N4
film, in this case deposited on carbon, at a substrate tempera-ture of 200 °C for 300 s solid circles. Carbon is used assubstrate in the RBS measurements in order to eliminate thehigh background signal from the more commonly used Sisubstrate. In this figure one can see the N and Si signals fromthe silicon nitride film, as well as some Ar incorporated dur-ing the sputtering process. The element areal densities areproportional to the areas under the corresponding peaks. Thisspectrum also shows that the films are free from contami-nants such as O and Fe, within the RBS sensitivity, whichcould modify several of their properties, such as hardnessand adhesion.29,30 In Fig. 1b, the Si to N ratio is presentedas a function of N2 partial pressure during deposition for two
TABLE I. Deposition parameters for Si3N4 films.
Base pressure mbar 510−7
Ar partial pressure mbar 310−3
N2 partial pressure mbar 0.7–1210−3
RF power density W cm−2 7.7Substrate temperature °C 23–500Deposition time s 15–3000Target to substrate distance mm 60
073521-2 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
substrate temperatures, room temperature solid squares anddashed line and 400 °C solid triangles and solid line,while keeping a constant Ar partial pressure of 310−3 mbar. The total pressure during deposition can becalculated adding the Ar partial pressure to the N2 partialpressure. The straight dashed line shows the Si to N atomicratio for stoichiometric Si3N4, namely 0.75. For depositionsat room temperature, no stoichiometric silicon nitride is ob-served for any N2 partial pressure used, indicating an N ex-cess in the films. At 400 °C, we observe a Si excess fordepositions at N2 partial pressures below 110−3 mbar,while an N excess is observed for N2 partial pressure above710−3 mbar. Between 1 and 710−3 mbar, stoichio-metric silicon nitride is formed at 400 °C. Further deposi-tions were carried out using a N2 partial pressure of 310−3 mbar, in order to keep the total pressure during depo-
sition 610−3 mbar in this case as low as possible, maxi-mizing the mean free path in the deposition chamber. Usingthis Ar and N2 constant partial pressures, we investigated thestoichiometry of the films as a function of the substrate tem-perature during deposition, showed in Fig. 1c. We observedthat only for room temperature deposition, the silicon nitridefilm is not stoichiometric, while for all other temperaturesused, Si3N4 is observed. This result indicates that some acti-vation energy, higher than the energy provided at room tem-perature, is necessary to obtain stoichiometric silicon nitride.It is important to remember that several properties of siliconnitride depend on stoichiometry, such as refraction index andhardness.14,31 Moreover, the possibility to obtain Si3N4 filmsat substrate temperatures as low as 100 °C, allows the depo-sition of silicon nitride in different kinds of substrates.
GAXRD results are shown in Fig. 2 for Si3N4 films de-posited on Si at substrate temperatures of 23 °C solidsquares, 200 °C open circles, and 500 °C solid tri-angles. The positions of the main diffraction peaks of the-Si3N4 open squares and -Si3N4 solid lozenges phasesare also indicated. It can be seen that the films are essentiallyamorphous after deposition, except for the deposition at500 °C where some diffraction peaks attributed to the-Si3N4 phase are observed, which is considered a meta-stable phase. We must stress that the crystalline structure ofthe coatings plays an important role in mechanical proper-ties, since the crystalline phases of silicon nitride are harderthan the amorphous phase.32,33 This point will be discussedbelow, following the annealing results.
In order to convert the N areal densities obtained fromRBS to film thickness, it is important to determine the den-sity of the films. Moreover, a correlation between the me-chanical properties of silicon nitride films and its density hasbeen proposed.34 In this way, the Si3N4 density was deter-mined using the XRR technique, from which it is also pos-sible to evaluate the abruptness of the interface between thefilm and the substrate. Figure 3 shows the XRR data from aSi3N4 film deposited at 200 °C for 30 s solid squares andthe simulation line. The results from the simulation areshown in the inset, where a density of 3.01 g cm−3 and athickness of 55 nm were obtained. The density figure is ingood agreement with previous results34,35 for amorphous
FIG. 1. a Rutherford backscattering spectroscopy spectrum from a Si3N4
film deposited on carbon at 200 °C solid circles. The different elementspresent in the sample are indicated as well as the position for the Iron 56Fesignal. Inset: experimental setup for the RBS analyses. b Silicon to nitro-gen ratio in Si3N4 films deposited at 400 °C solid triangles and solid lineand room temperature solid squares and dot line as a function of the N2
partial pressure during deposition. The dashed line represents the optimalSi/N ratio. c Silicon to nitrogen ratio for Si3N4 films open circles depos-ited with a N2 partial pressure of 310−3 mbar as a function of the depo-sition temperature. Lines are only to guide the eyes.
FIG. 2. Grazing angle x-ray diffraction of Si3N4 films deposited at 23 °Csolid squares, 200 °C open circles, and 500 °C solid triangles. Thepositions of the main diffraction peaks from -Si3N4 solid lozenge and-Si3N4 open squares are indicated. a.u.=arbitrary units.
073521-3 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
Si3N4 films. Considering the density from the XRR simula-tion, a relation between the total N amount and the filmthickness was calculated,
1015 N cm−2 = 0.18 nm. 1
The simulation also shows that the roughness of the in-terface between Si3N4 and Si is about 1 nm.
Figure 4a shows the N and Si areal densities in Si3N4
films deposited at 200 °C as a function of deposition time.The vertical scale is logarithmic for better visualization. TheN and Si total amounts show a linear increase with deposi-tion time, as well a 0.75 Si to N ratio for all deposition timesemployed. Using relation 1 we convert the total N amountto Si3N4 film thickness, showed in Fig. 4b. A linear relationbetween film thickness and deposition time was obtained,with a deposition rate of 1.6 nm/s 0.5 m /h. This is anecessary relationship for any practical application, since thethickness of the coating plays an important role. In this way,
to determine the mechanical properties of the films, a depo-sition time of 120 s was used, yielding a film thickness of192 nm. Since in the nanoindentation measurements a maxi-mum depth of 20 nm was used, only 10% of the film thick-ness is probed, eliminating the substrate contribution.
Figure 5a shows the hardness open circles of theSi3N4 films deposited on Si as a function of substrate tem-perature during deposition. Each point is obtained from anaverage of 20 measurements in different spots on the samplesurface. A small increase in hardness is observed when thesubstrate temperature is increased from 23 to 200 °C. Thishardness figures 19.5–22 GPa are consistent with those foramorphous silicon nitride reported in the literature.14,34,36
However, when the substrate temperature is increased from200 to 500 °C, a reduction in hardness is observed from 22to 16.5 GPa. Before discussing the observed behavior ofSi3N4 film hardness with temperature, we must make someconsiderations regarding the internal stress of the films. Pre-vious results in metal nitride films deposited by sputtering,like AlN and MoNx, show that the gas pressure during depo-sition determines the type of intrinsic residual stress in thefilms.37,38 For deposition pressures below 1310−3 mbar,the internal stress is essentially compressive, while abovethis pressure the stress becomes tensile. Since our deposi-tions were performed at 610−3 mbar, we assume that theinternal stress of the present films is compressive. Moreover,the origin of the residual stress can be attributed to the ther-mal residual stress extrinsic and to the intrinsic stress dueto the film growth process. However, the coefficient of ther-mal expansion of the silicon substrate 3.5–410−6 /KRef. 39 and that of Si3N43–3.710−6 /K Ref. 40 are
FIG. 3. XRR data solid squares of Si3N4 films deposited on Si at 200 °Cfor 30 s and the respective simulation solid line. The density in g cm−3and the thickness in nanometer of the film obtained from the simulationare presented in the inset. CPS stands for counts per second.
(a)
(b)
FIG. 4. a Silicon and nitrogen total amounts in Si3N4 films deposited at200 °C as a function of deposition time. b Thickness of Si3N4 films as afunction of deposition time. The deposition rate k obtained from linear fitof the data is presented.
FIG. 5. a Hardness open circles of the Si3N4 films as a function ofdeposition temperature. b Left-hand side: reduced elastic modulus solidcircles as a function of deposition temperature. Right-hand side: H3 /Er
2
open squares as a function of deposition temperature. Lines are only toguide the eyes.
073521-4 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
rather similar, making the residual thermal stress contribu-tion negligible. In this way, the increase in hardness observedin the 23 and 200°C substrate temperature range is attributedto an increase in the compressive internal stress of the film.Indeed, correlations between hardness increase and compres-sive internal stress increase, in some cases linear correla-tions, have been reported41–43 for TiN, ZrN, and TiCxN1−x
films deposited on different types of substrates, corroboratingour assumption. The decrease in hardness observed for tem-peratures above 200 °C is attributed to the relaxation of thecompressive internal stress, since the beginning of the crys-tallization of the Si3N4 film, observed for sample depositedat 500 °C, helps the relaxation of the internal stress, thusreducing the hardness. Although the internal stress of thefilms were not measured here, this behavior has been ob-served previously44 in the deposition of SiC films on Si.Figure 5b shows the reduced elastic modulus solid circles,left-hand side obtained from the load-displacement curvesand the elastic strain to failure H3 /E2 open squares, right-hand side. The reduced elastic modulus behavior is similarto the hardness behavior, a slight increase in the 23–200 °Csubstrate temperature range and a decrease in the200–500 °C range. This can be explained with the sameargument presented above of increase in the internal stress,and further relaxation for higher substrate temperatures. Cor-relation between the compressive internal stress and the elas-tic modulus has also been reported.42 Although the modula-tions in the internal stress help to explain the observedvariations in hardness, other mechanisms cannot be disre-garded, such as grain size changes and point defects in thefilms. Moreover, the complicated interplay between the dif-ferent factors affecting films hardness still remains as a pointof discussion, especially in superlattice structures. TheH3 /E2, commonly used to foresee the wear resistance ofcoatings, remains constant 0.25 GPa for all substrate tem-perature used in this work. This happens since the increase/decrease in hardness is followed by the same increase/decrease in the reduced elastic modulus when the substratetemperature is varied.
IV. MECHANICAL AND STRUCTURAL PROPERTIESOF SI3N4 FILMS AFTER 18O2 ANNEALING
The hardness of Si3N4 films deposited at different sub-strate temperatures, namely 100 °C solid squares anddashed line, 200 °C open circles and solid line, and500 °C solid triangles and dotted line, as a function ofannealing temperature in 18O2 are shown in Fig. 6a. In thethree samples, a reduction in hardness is observed annealingat 250 °C, while for annealing at 500 °C, the sample depos-ited at 200 °C presents a progressive decrease in hardness,but samples deposited at 100 and 500 °C show some in-crease. This is once again attributed to changes in the inter-nal stress of the films. Since the sample deposited at a sub-strate temperature of 200 °C presents the highest hardnessafter deposition, it should present the highest internal stress.Following this reasoning, the annealing at 250 and 500 °Cinduces a relaxation of this stress, reducing the hardness ofthe film. The pictures changes for the sample deposited at
500 °C, since it has a lower hardness, it should also presenta lower internal stress. In this way, the annealing at 250 °Cmay induce some relaxation of the remaining internal stress,but the effect is less pronounced than for the 200 °C sample.When the annealing is performed at 500 °C, an increase inhardness is observed, which should be related to a differentprocess, rather than increase/decrease of the internal stress.The sample deposited at 100 °C presents a similar, althoughless pronounced, behavior as compared to the sample depos-ited at 500 °C. Finally, when the annealing is performed at1000 °C, all investigated samples present an increase inhardness, approaching the same value within the experimen-tal error, namely 21 GPa. This effect will be discussed be-low in conjunction with the structural properties of the an-nealed films. Since the samples annealed at 1000 °C presentan increase in hardness, which is a highly desirable effect forhard coatings in high temperature applications, we investi-gated other mechanical properties of the films deposited atdifferent substrate temperatures after the 1000 °C annealing.Figure 6b shows the reduced elastic modulus solidsquares, left-hand side obtained from the load-displacementcurves and the elastic strain to failure H3 /E2 open triangles,right-hand side for Si3N4 films after the 1000 °C annealing,as a function of substrate temperature during deposition.Here we used the reduced elastic modulus to estimate theelastic strain to failure H3 /E2. A progressive reduction inthe reduced elastic modulus after 1000 °C annealing is ob-served when the substrate temperature is increased, exceptfor the sample deposited at 500 °C. This sample presents thesame Er before and after annealing, as shown in Figs. 5b
FIG. 6. Hardness of Si3N4 films deposited at 100 °C solid squares,200 °C open circles, and 500 °C solid triangles as a function of 18O2
annealing temperature. b Left-hand side: reduced elastic modulus solidsquares as a function of deposition temperature after 18O2 annealing at1000 °C. Right-hand side: H3 /Er
2 open triangles as a function of deposi-tion temperature after 18O2 annealing at 1000 °C. Lines are only to guidethe eyes.
073521-5 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
and 6b. This indicates that the properties of the Si3N4 filmsafter deposition before annealing play some role on themechanical properties after annealing. Composition differ-ences cannot account for this, since all films are stoichio-metric and free from contaminants. However, their structurespresent some differences, as presented in Fig. 2 where thesample deposited at 500 °C has some crystalline order, whilefor all not shown other temperatures investigated, the filmsare amorphous. In this way, the decrease in the reduced elas-tic modulus for samples deposited at 100, 200, and 300 °Cafter annealing at 1000 °C, may be related to some structuralchanges in the films and/or to changes in the internal stress.The elastic strain to failure H3 /E2 presented in the right-handside of Fig. 6b also present some changes after the1000 °C annealing. Here we observe a considerable increasein the H3 /E2 for all samples after annealing from 0.25 to0.4–0.48 GPa, which his close to a factor of 2. This is an-other highly desirable effect for high temperatures applica-tions.
Figure 7 shows the GAXRD of Si3N4 films as-depositedat a substrate temperature of 200 °C solid circles and after18O2 annealing at 500 °C open circles and 1000 °C solidtriangles. According to Fig. 2, the as-deposited sample isessentially amorphous. However, annealing at 500 °C in-duces partial crystallization in the form of -Si3N4. The crys-tallization becomes more pronounced when the annealing isperformed at 1000 °C, although other diffraction peaks fromthe -Si3N4 phase were not observed, possibly due to pref-erential orientation. Si3N4 crystallization induced by anneal-ing has been reported,11 where the authors showed that the-Si3N4 phase is observed only at higher annealing tempera-tures and times, namely 1600 °C and 8 h, respectively. Weattribute the increase in hardness and the decrease of thereduced elastic modulus after annealing at 1000 °C observedin Fig. 6a to this crystallization process, since the crystal-line phase of Si3N4 is harder than the amorphous phase. In-deed, the behavior observed in Fig. 6a is attributed to acompetitive process between internal stress relaxation de-creasing hardness and crystallization increasing hardness.In the sample deposited at 200 °C and annealed at 250 and500 °C, internal stress relaxation is favored, since the an-nealing temperature is not high enough to induce significant
crystallization. When the annealing is performed at 1000 °C,the crystallization is favored and the hardness is increased.This competitive process also happens to a certain extent insamples deposited at 100 and 500 °C. Moreover, we cannotdisregard that during the 18O2 annealing, oxidation of theSi3N4 may take place, as well as the fact that silicon oxideSiO2 and silicon oxynitrides SiOyNx present lower hard-ness figures14,36 than stoichiometric Si3N4, either in amor-phous or crystalline forms. In this way, the formation ofsome oxide or oxynitride layer may contribute to a reductionin hardness, but this reduction can be compensated by thecrystallization process. The next section will show results inoxygen and nitrogen atomic transport during annealing thatshed some light into this issue.
V. OXYGEN AND NITROGEN ATOMIC TRANSPORT INSI3N4 DURING 18O2 ANNEALING
Figure 8a shows the experimental excitation curvessymbols for the 18Op,15N nuclear reaction around theresonance energy Er=151 keV and the corresponding simu-lations lines for Si3N4 deposited at 200 °C for 120 s andannealed in 18O2 at 250 °C solid squares and solid line,500 °C open circles and dashed line, and 1000 °C solidtriangles and dotted line. From the simulations is possible toobtain the 18O profiles presented in Fig. 8b, where they-axis stand for 18O concentration normalized for oxygen instoichiometric SiO2. Sample annealed at 250 °C solid linepresents small 18O incorporation, only 1.2% and 2 nm indepth. When the annealing temperature is increased to
FIG. 7. Grazing angle x-ray diffraction of Si3N4 films deposited at 200 °Csolid circles and after 18O2 annealing at 500 °C open circles and1000 °C solid triangles. The positions of the main diffraction peaks from-Si3N4 solid lozenge and -Si3N4 open squares are indicated.
FIG. 8. Experimental excitation curves symbols of the 18Op,15Nnuclear reaction around the resonance energy Er=151 keV and the corre-sponding simulations lines for samples annealed in 18O2 at 250 °C solidsquares and solid line, 500 °C open circles and dashed line, and 1000 °Csolid triangles and dotted line. b 18O profiles obtained from the simula-tion of the excitation curves presented in a. Line types are the same as ina. 18O concentration is normalized to oxygen in stoichiometric SiO2.
073521-6 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
500 °C, 18O incorporation increases to 18% close to the filmsurface, but again in a narrow region of the film surface, only3.5 nm. Annealing at 1000 °C leads to 75% incorporationnear the surface, but located only 7 nm away from the filmtop surface. Moreover, the shape of the profiles at 500 and1000 °C annealing resembles a diffusion limited process,close to an complementary error function ercf-like profile.It must be pointed out that Si3N4 is commonly used as adiffusion barrier in the microelectronic industry. This resultsshow the great oxidation resistance of the Si3N4 submitted tothermal annealing, since even after annealing at 1000 °C fora 1 h, oxygen is incorporated only in 7 nm in depth. Theoxygen atoms incorporated therein may react with the Si3N4
network forming silicon oxynitride or silicon oxide. Indeed,tribological properties friction and wear rate of monolithicSi3N4 containing different crystalline phases were reported45
showing that the friction coefficient and wear rate were re-duced when surface layers, such as SiO2, and SiOxNy, wereformed during tribological tests at 1000 °C. However, whenthe tests were performed at 400 °C, no reduction in the wearrate and friction coefficient was observed, since at this tem-perature no significant layer of silicon oxynitride or siliconoxide is formed, as shown in this work.
Figure 9a shows the experimental excitation curvessymbols for the 15Np,12C nuclear reaction around theresonance energy Er=429 keV and the corresponding simu-lations lines for Si3N4 deposited at 200 °C for 120 s opentriangles and dashed-dotted line and annealed in 18O2 at250 °C solid squares and solid line, 500 °C open circles
and dashed line and 1000 °C solid triangles and dottedline. From the simulation it is possible to obtain the 15Nprofiles presented in Fig. 9b. The 0.4% 15N concentrationin y-axis of Fig. 9b stands for N concentration in stoichio-metric silicon nitride, since this is the isotopic natural abun-dance of 15N. Nitrogen profile of the as-deposited sampleopen triangles and dashed-dotted line is a horizontalstraight line at 0.4% in N concentration, indicating the depo-sition of a homogeneous and stoichiometric silicon nitride.After annealing at 250 °C solid square and solid line, weobserve a small variation in N distribution, only 1 nm indepth from the film surface. However, when the sample isannealed at 500 °C, nitrogen is partially removed from thefilm in a 5 nm thick region, whereas annealing at 1000 °Cremoves nitrogen from an 8 nm thick region. Comparing theregions where nitrogen was removed from the films duringannealing to where 18O was incorporated Fig. 8b, it ispossible to conclude that both processes occur more or lessin the same regions of the Si3N4 films. This indicates thatduring the 18O annealing, oxygen is incorporated in the sameregion where nitrogen is removed, in a solid-gas reaction,thus probably forming silicon oxynitride between 1 and 8nm thick of variable composition near the Si3N4 surface.This great oxidation resistance and some possible solid-gasreactions between Si3N4 and O2 has been reported46 in-Si3N4–Y2Si2O7 ceramics annealed in air for different an-nealing times at 1000 and 1200 °C. Nevertheless, thegradual interface between the silicon oxynitride layer formedduring annealing and the silicon nitride film should lead to agood adhesion between them. This should improve the solidlubricant effect of the silicon oxynitride layer in tribologicalapplications at high temperatures, as reported for bulkSi3N4.45
To confirm the hypothesis of silicon oxynitride forma-tion during annealing, XPS measurements were performed toevaluate the N and Si chemical ambient in the annealed andas-deposited films. Figure 10a shows the photoelectron re-gion for Si 2p for a Si3N4 deposited at 200 °C for 120 ssolid circles, about 192 nm thick and after 18O2 annealing
FIG. 9. Experimental excitation curves symbols of the 15Np,12Cnuclear reaction around the resonance energy Er=429 keV and the corre-sponding simulations lines for the as-deposited sample open triangles anddashed-dotted line as well as for samples annealed in 18O2 at 250 °C solidsquares and solid line, 500 °C open circles and dashed line, and 1000 °Csolid triangles and dotted line. b 15N profiles obtained from the simula-tion of the excitation curves presented in a. Line types are the same as ina. 15N concentration of 0.4% corresponds to stoichiometric Si3N4.
FIG. 10. a Si 2p and b N 1s x-ray photoelectron spectra a.u.=arbitrary units at take-off angle of 45° for Si3N4 films deposited at 200 °Csolid circles and solid line and after 18O2 annealing at 1000 °C solidtriangles and solid line. Energy positions for Si–N and Si–O–N environ-ments are indicated. Lines stand for fittings.
073521-7 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
at 1000 °C solid triangles. In the as-deposited sample weidentify one single component attributed to Si bonded to N inthe form of stoichiometric silicon nitride,47,48 confirming ourRBS results. After 18O2 annealing at 1000 °C, a shift of thissingle component to higher binding energies is observed.This is a clear evidence of reaction between oxygen from thegas phase and the silicon nitride film, forming SiOxNy,which confirms our assumption. Figure 10b shows the pho-toelectron region for N 1s for the same sample, Si3N4 as-deposited solid circles and after 18O2 annealing at 1000 °Csolid triangles. The as-deposited sample also presents asingle N chemical state attributed to N bonded to Si in stoi-chiometric silicon nitride. When the sample is submitted to18O2 annealing at 1000 °C two conclusion can be made, ireduction of the N content near the film surface, since thephotoelectron intensity of the annealed sample is lower thanthe as-deposited sample and ii shift of the single compo-nent to a higher binding energy, indicating the formation ofsilicon oxynitride.
VI. CONCLUSION
In summary, we investigated the physicochemical, struc-tural, and mechanical properties of Si3N4 films before andafter 18O2 annealing. Films were stoichiometric for a sub-strate temperature range of 100–500 °C and essentiallyamorphous, except for the sample deposited at 500 °C,where some diffraction peaks from the -Si3N4 phase areobserved. Hardness and reduced elastic modulus variationswith substrate temperature were also observed, which areattributed to changes in the internal stress of the films. Amaximum hardness of 22 GPa was observed for the sampledeposited at a substrate temperature of 200 °C, which leadsto an elastic strain to failure of 0.25 GPa. After 18O2 anneal-ing at 1000 °C, the hardness of Si3N4 films deposited atdifferent substrate temperature where seen to increase, con-verging to 21 GPa, which is a very interesting effect for hightemperature applications, since most of the coatings suffersignificant hardness reduction at this temperature. Moreover,oxygen is observed to incorporate only in 7.5 nm from thefilm surface, even after annealing for 1 h, indicating a highoxidation resistance of the Si3N4 coating. The hardnessmodulation after annealing was explained based on two com-petitive processes, the crystallization of the films, which ledto an increase in hardness and to oxidation of the film andrelaxation of the internal stress, leading to a decrease in hard-ness. These competitive processes keep the hardness figuresclose to 21 GPa for all investigated films after 1000 °C an-nealing, since at this temperature the crystallization of thefilm is favored. Finally, the H3 /E2 figures almost doublesafter the high temperature annealing which is one more de-sirable affect for high temperatures applications. The presentresults may also help to understand the superhardness ofSi3N4 /TiN multilayers, since it is important to know theproperties of each individual layer in order to completelyexplain the still open issue of multilayer superhardness. Nev-ertheless, the promising mechanical properties of the Si3N4
as a coating for high temperature applications were demon-strated. Tribological characterization nanowear and friction
coefficient of the films, before and after annealing, is inprogress in our laboratory in order to demonstrate the fullpotentiality of Si3N4 as a hard coating for high temperatureapplications.
ACKNOWLEDGMENTS
The authors would like to acknowledge MCT/CNPq andCAPES for financial support.
1Y. C. Chim, X. Z. Ding, X. T. Zeng, and S. Zhang, Thin Solid Films 517,4845 2009.
2S. Veprek and M. J. G. Veprek-Heijman, Surf. Coat. Technol. 202, 50632008.
3P. E. Hovsepian and W.-D. Münz, Nanostructured Coatings Springer,New York, 2006.
4V. Derflinger, H. Brändle, and H. Zimmermann, Surf. Coat. Technol. 113,286 1999.
5H. Hoche, D. Allebrandt, M. Bruns, R. Riedel, and C. Fasel, Surf. Coat.Technol. 202, 5567 2008.
6C. A. Powell and B. D. Morreale, MRS Bull. 33, 309 2008.7M. B. da Silva and J. Wallbank, J. Mater. Process. Technol. 88, 1951999.
8L. Yu, S. Dong, J. Xu, and I. Kojima, Thin Solid Films 516, 1864 2008.9T. Polcar, R. Martinez, T. Vítü, L. Kopecký, R. Rodriguez, and A. Cava-leiro, Surf. Coat. Technol. 203, 3254 2009.
10A. Ziegle, J. C. Idrobo, M. K. Cinibulk, C. Kisielowski, N. D. Browning,and R. O. Ritchie, Science 306, 1768 2004.
11H. Schmidt, W. Gruber, G. Borchardt, M. Bruns, M. Rudolphi, and H.Baumann, Thin Solid Films 450, 346 2004.
12Y. Toivola, J. Thurn, and R. F. Cook, J. Appl. Phys. 94, 6915 2003.13H. Chen, J. Liu, and W. Huang, Mater. Sci. Eng., A 415, 291 2006.14Y. Liu, I.-K. Lin, and X. Zhang, Mater. Sci. Eng., A 489, 294 2008.15P. Kroll, J. Non-Cryst. Solids 351, 1127 2005.16V. Vila, D. Caceres, and C. Prieto, J. Appl. Phys. 94, 7868 2003.17F. H. P. M. Habraken and A. E. T. Kuiper, Mater. Sci. Eng. R. 12, 123
1994.18C. Savall, J. C. Bruyère, and J. P. Storquet, Thin Solid Films 260, 174
1995.19A. Leyland and A. Matthews, Wear 246, 1 2000.20F. Lv, S. P. Wen, R. L. Zong, F. Zeng, Y. Gao, and F. Pan, Surf. Coat.
Technol. 202, 3239 2008.21J. Suna, J. Musil, V. Ondok, and J. G. Han, Surf. Coat. Technol. 200, 6293
2006.22Y. Pauleau and F. Thiery, Surf. Coat. Technol. 180–181, 313 2004.23J. Soldán and J. Musil, Vacuum 81, 531 2006.24S. Yang, Y. Chang, D. Lin, D. Wang, and W. Wu, Surf. Coat. Technol. 202,
2176 2008.25L. C. Feldman, J. W. Mayer, and S. T. Picraux, Materials Analysis by Ion
Channeling Academic, New York, 1982.26L. G. Parratt, Phys. Rev. 95, 359 1954.27I. J. R. Baumvol, Surf. Sci. Rep. 36, 1 1999.28R. P. Pezzi, P. L. Grande, and M. Copel, Surf. Sci. 601, 5559 2007.29S. Hao, B. Delley, S. Veprek, and C. Stampfl, Phys. Rev. Lett. 97, 086102
2006.30C. W. M. e Silva, E. Alves, A. R. Ramos, C. S. Sandu, and A. Cavaleiro,
Vacuum 83, 1213 2009.31W. J. Gunning, R. L. Hall, F. J. Woodberry, W. H. Southwell, and N. S.
Gluck, Appl. Opt. 28, 2945 1989.32P. Walsh, A. Omeltchenko, R. K. Kalia, A. Nakano, P. Vashista, and S.
Saini, Appl. Phys. Lett. 82, 118 2003.33P. Wei, L. Chen, A. Okubo, and T. Hirai, Mater. Lett. 49, 239 2001.34H. Huang, K. J. Winchester, A. Suvorova, B. R. Lawn, Y. Liu, X. Z. Du,
J. M. Dell, and L. Faraone, Mater. Sci. Eng., A 435–436, 453 2006.35V. Verlaan, R. Bakker, C. H. M. van der Werf, Z. S. Houweling, Y. Mai, J.
K. Rath, and R. E. I. Schropp, Surf. Coat. Technol. 201, 9285 2007.36J. A. Taylor, J. Vac. Sci. Technol. A 9, 2464 1991.37Y. G. Shen, Mater. Sci. Eng., A 359, 158 2003.38G. L. Huffman, D. E. Fahnline, R. Messier, and L. J. Pilione, J. Vac. Sci.
Technol. A 7, 2252 1989.39Y. Okada and Y. Jukumaru, J. Appl. Phys. 56, 314 1984.40R. M. Williams, J. Am. Ceram. Soc. 63, 108 1980.
073521-8 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
41P. J. Martin, A. Bendavid, and T. J. Kinder, Surf. Coat. Technol. 81, 361996.
42L. Karlsson, L. Hultman, and J.-E. Sundgren, Thin Solid Films 371, 1672000.
43H.-M. Tung, J.-H. Huang, D.-G. Tsai, C.-F. Ai, and G.-P. Yu, Mater. Sci.Eng., A 500, 104 2009.
44M. Lattemann, S. Ulrich, H. Holleck, M. Stüber, and H. Lesite, Diamond
Relat. Mater. 11, 1248 2002.45A. Skopp, M. Woydt, and K.-H Habig, Wear 181/183, 571 1995.46S. P. Taguchi and S. Ribeiro, J. Mater. Process. Technol. 147, 336 2004.47J. Finster, E.-D. Klimkenberg, J. Heeg, and W. Braun, Vacuum 41, 1586
1990.48D. S. Blair, J. W. Rogers, Jr., and C. H. F. Peden, J. Appl. Phys. 67, 2066
1990.
073521-9 Aguzzoli et al. J. Appl. Phys. 107, 073521 2010
Downloaded 03 May 2010 to 143.54.100.91. Redistribution subject to AIP license or copyright; see http://jap.aip.org/jap/copyright.jsp
ANEXO 5
Surface & Coatings Technology 205 (2011) 4528–4531
Contents lists available at ScienceDirect
Surface & Coatings Technology
j ourna l homepage: www.e lsev ie r.com/ locate /sur fcoat
Nanoscale friction of partially oxidized silicon nitride thin films
J. Filla a, C. Aguzzoli a,b, V. Sonda a, M.C.M. Farias a, G.V. Soares b, I.J.R. Baumvol a,b, C.A. Figueroa a,⁎a Centro de Ciências Exatas e Tecnologia, Universidade de Caxias do Sul, Caxias do Sul, 95070-560, Brazilb Instituto de Física, Universidade Federal do Rio Grande do Sul, Porto Alegre, 91509-970, Brazil
⁎ Corresponding author.E-mail address: cafiguer@ucs.br (C.A. Figueroa).
0257-8972/$ – see front matter © 2011 Elsevier B.V. Adoi:10.1016/j.surfcoat.2011.03.111
a b s t r a c t
a r t i c l e i n f oArticle history:Received 2 February 2011Accepted in revised form 25 March 2011Available online 31 March 2011
Keywords:Silicon nitrideSilicon oxideNanoscale frictionIonic potential
The nanoscale friction of partially oxidized silicon nitride thin films deposited by reactive magnetronsputtering was investigated. Post deposition thermal annealing in O2, trying to simulate the oxidation byatmospheric oxygen in working conditions, formed a partially oxidized layer at the surface with maximumthickness around 10 nm. Unidirectional sliding tests showed a decrease of the low-load friction coefficients ofthe sliding pair for the samples annealed in oxygen as compared to the non-annealed ones. The results arediscussed on the lights of our extension of the crystal chemistry model, which establishes a relationshipbetween ionic potential and friction coefficient.
ll rights reserved.
© 2011 Elsevier B.V. All rights reserved.
1. Introduction
There is currently a trend to avoid the use of liquid lubricants incutting and machining of metallic and ceramic parts, due to environ-mental issues and production costs [1]. However, friction in dryconditions increases the temperature of both contacting surfaces up tomore than 1100 °C, leading to oxidation and to changes in themechanical properties of the original material, as well as to modifica-tions in the tribological behavior of the system [2,3]. In order to controlthese phenomena, the tribology of the system must be understood indetail. Recently, several physicochemical concepts and models havebeenused toexplain the relationshipsbetween thenatureor products oftribochemical reactions and friction [4–8]. For example, deuteriumchemisorbed on diamond or silicon surfaces leads to nanoscale frictioncoefficients lower thanhydrogen chemisorbed on the same surfaces [5].This was attributed to the lower natural frequency of the carbon(silicon)–deuterium bond as compared to the carbon(silicon)–hydro-gen bond, which implies a reduction in the rate at which the kineticenergy of the tip is dissipated. Other advances were reached based on amodel, to be discussed below, that connects the ionic potential (φ) andthe average friction coefficient of various oxides [7,8].
Silicon nitride (Si3N4) is a ceramic material with a relatively highhardness, thermodynamic stability, and oxidation resistance at hightemperatures [9,10]. Most of the cutting-edge coating materials used indry machining operations which have been developed by plasmadeposition technologies, contain Si3N4 as a main component in severalnanocomposite systems [11,12]. Although the hardness of Si3N4 canachieve a newmaximum (~22 GPa) at 1000 °C due to awell established
phase transition (amorphous to alpha) [13], the role of Si3N4 inmaintaining the hardness and wear resistance of composites at hightemperatures is still not fully understood.
The aim of the present study is to investigate both the nanoscalefriction and mechanical properties of partially oxidized Si3N4 thinfilms, in an attempt to contribute to clarifying the low friction andhardness stability at high temperatures of this material.
2. Materials and experimental procedure
Si3N4 filmswere deposited on Si(001) substrates by radio frequency(RF) reactivemagnetron sputtering. Prior to deposition, substrateswerecleaned in ultrasonic acetonebath, followed bya second cleaning step in10% hydrofluoridric acid solution and immediately loaded in thesputtering vacuum chamber, which was pumped down to a basepressure of 5×10−5 Pa. A 2 inchdiameter, highpurity (N99.99%) silicontargetwas used, located 60mmaway from the substrate, and Si3N4 filmdepositions were performed using a mixture of argon and nitrogengasses, with a constant partial pressure of 3×10−1 Pa in both cases.Such partial pressures guarantee a Si:N stoichiometry of 3:4, for sampletemperatures during deposition (hereafter called DT) higher than100 °C, as determinedbyRutherford backscattering spectroscopy (RBS).An input RF power density of 7.4 W·cm−2 was employed with areflected power density lower than 0.05W·cm−2. DT was varied fromroom temperature (23 °C) to 500 °C. The deposition time was fixed in300 s in order to achieve a final thickness of 500 nm in all samples. Nodelamination of the films was observed.
In order to simulate high temperature oxidation of the as-deposited Si3N4 coatings in machining or cutting conditions, sampleswere loaded in a static pressure, resistively heated quartz furnace,which was pumped down to 2×10−5 Pa, before being pressurizedwith oxygen enriched to 97% in the isotope of mass 18. Oxidation
0 100 200 300 400 50016
18
20
22
As deposited
OA 500oC
OA 1000oC
Har
dnes
s (G
Pa)
Deposition temperature (oC)
Fig. 2. Hardness profiles versus substrate temperature during deposition of Si3N4 thinfilms before and after oxygen annealing.
4529J. Filla et al. / Surface & Coatings Technology 205 (2011) 4528–4531
annealing (hereafter called OA) was performed here in 104 Pa of 18O2
for 4 h at two different temperatures, namely 500 °C or 1000 °C. Theuse of the 18O rare isotope allows us to distinguish it from the oxygenpreviously incorporated in the films due to contamination duringdeposition or to atmospheric air exposure.
The elementary compositions of the films were quantitativelydetermined by RBS with a sensitivity of 1014 atoms×cm−2 (about 1/10 of a monolayer) and 10% accuracy [14]. The hardness and frictionmeasurements were accessed by nanoindentation and nanoscalesliding wear tests, respectively, using a NanoTest-600 equipmentmanufactured by Micro Materials Ltd, equipped with a three-sidedpyramidal diamond tip (Berkovich indenter). The unloading portionof load-depth curves was analyzed, allowing estimating values forfilm hardness [15]. Nanoindentation tests were performed at a loadrate of 0.1 mN·s−1 and a maximum indentation depth of 50 nm. Thesubstrate effect on hardness measurements appears when theindentation depth reaches between 10% and 20% of the totalthickness. In order to avoid the substrate effect, we chose the lowerlimit (10%) to perform our measurements. Normal loads of 5, 10, and20 mN were applied to the Berkovich indenter (used as the counter-face) and the samples were then displaced once at a rate of 1 μm·s−1
to a total distance of 300 μm. The tangential force was measured by aload cell and its average steady-state value was related to the frictionforce of the layer formed at the surface of the Si3N4 films before andafter OA. The 18O profiles were determined by narrow nuclearresonant reaction profiling [16] (NRP) using the narrow resonances(Γ=100 eV) in the cross section curves of the 18O(p,α)15N nuclearreactions at 151 keV. Simulations of the nuclear reaction excitationcurves were carried out using the FLATUS code [17]. The wear trackswere analyzed using a Shimadzu SSX-550 scanning electron micro-scope (SEM) in secondary electron mode. The characterization of theSi3N4 films, before and after annealing in oxygen was performed bythe authors and published elsewhere [13].
3. Results and discussion
Fig. 1 shows the oxygen content (%) as a function of depth in theSi3N4 thin films deposited at different DT and submitted to OA at500 °C or 1000 °C, as obtained from the NRP measurements. Here,100% corresponds to the concentration of 18O in a film made of Si18O2,
used as a standard. One can see that very thin partially oxidized layers,only a few nanometers thick were obtained. The oxygen profiles inSi3N4 are erfc-like, indicating a diffusion-limited process. In addition,for 4 h of OA the thickness of the oxidized layers was similar to thoseobtained in a previous work [13] for OA during 1 h.
Fig. 2 shows the hardness versus DT of Si3N4 thin films before andafter OA, indicating that the hardness increased slightly with DT,
0 3 6 9 120
20
40
60
80
100
DT 23oC; OA 1000oC
DT 300oC; OA 1000oC
DT 500oC; OA 1000oC
DT 23oC; OA 500oC
DT 300oC; OA 500oC
DT 500oC; OA 500oC
18O
(%
)
Depth (nm)
Fig. 1. Oxygen content (%), obtained from the narrow resonant nuclear profiling, as afunction of depth in Si3N4 thin films deposited at different substrate temperatures andannealed in oxygen at 500 °C or 1000 °C.
reaching maxima of 20–22 GPa. The hardness, on the other hand, didnot change significantly after OA. Such mechanical stability in a widerange of temperatures allows the use of Si3N4 films in cutting andmachining applications where high temperatures are developed.
Fig. 3 shows the friction coefficients as a function of the slidingdistance at different normal loads for Si3N4 thin films, DT=500 °C,before and after OA at 500 °C or 1000 °C, respectively. The averagesteady-state friction coefficient values (AFC) are also shown for each
Fig. 3. a–c. Friction coefficient versus sliding distance at different normal loads for Si3N4
thin films deposited at 500 °C, before and after annealing in oxygen at 500 °C or1000 °C, respectively. The average friction coefficients for each curve are also shown.
Fig. 4. Average friction coefficients versus surface roughness for Si3N4 thin filmsdeposited at 500 °C, before and after annealing in oxygen at 500 °C or 1000 °C.
4530 J. Filla et al. / Surface & Coatings Technology 205 (2011) 4528–4531
condition. The as-deposited samples displayed friction coefficientswith low dispersion among curves, such that the average steady-statefriction coefficient values did not change more than 0.01 for differentnormal loads (see Fig. 3a). The friction coefficients determined in thepresent work for the films before OA (0.04±0.01) can be consideredload independent. For the samples after OA, the friction coefficientsvary substantially with load. Repeated measurements in the samesliding conditions confirmed the above reported results. Furthermore,a similar behavior was observed here in Si3N4 thin films deposited atlower substrate temperatures before and after OA. The frictioncoefficient depends on several parameters in the macro, micro, andnano-scales as, for instance, surface roughness. The surface roughnessof the samples was measured simultaneously with the frictioncoefficient measurements. Fig. 4 shows that surface roughnessincreases with the increase of the OA temperature. Consequently,the increase in friction coefficient after OA can be attributed to theincrease of surface roughness. Furthermore, the number of asperitycontacts and interlocking asperities of rubbing surfaces also increaseswith the increase of the normal load to 10 mN and 20 mN, which isanother cause for the increase of the friction coefficient. Finally, highernormal loads can lead to plastic deformation of the soft substratematerial, the Si3N4 film and the oxide layer. This contact mechanismmay result in a higher friction coefficient.
Fig. 5 shows two relevant facts that may contribute to explain suchexperimental results. Considering Si3N4 films deposited atDT=500 °C and OA at 1000 °C, followed by runs with normal loads
Fig. 5. a and b. Scheme of the indenter tip penetrating the oxygen annealed Si3N4 thin film anon a well adhered Si3N4 thin film deposited at 500 °C and annealed in oxygen at 1000 °C (b
of 5, 10, and 20 mN, one notices that the indenter tip penetrated thefilms up to depths of 110, 190, and 260 nm, respectively. In thosesliding conditions, the films did not suffer spalling and, consequently,themeasured friction coefficients correspond to those of well adheredSi3N4 films on silicon (100) obtained at different DT before OA(Fig. 3a) and to those partially oxidized layers (Fig. 1) formed after OA(Fig. 3b and c). Fig. 5a shows a drawing of the Berkovich indentertoward the inside of the film at a peak load of 20 mN. Trigonometriccalculations give a maximum length of the projected contact side of900 nm at 260 nm indentation depths, in agreement with the SEMimage where the width of the wear track is roughly 1000 nm wide(Fig. 5b). Considering the area function of an ideal Berkovich tip, theproportion of oxynitride in contact to the indenter is 17.4%, 10.3%, and7.5% for normal loads of 5 mN, 10 mN, and 20 mN, respectively. Thus,a lower penetration depth yields a higher oxide proportion in contactwith the indenter.
The results shown above can be discussed on the lights of crystalchemistry models. There is an established relationship between ionicpotentials (φ=Z/r) and average friction coefficient of various oxides[7,8]. Here, Z stands for the cationic charges and r for the cation radii.Oxides with higher ionic potentials (cations with higher charge and/or smaller radius) show screened cations by surrounding anions andhence their friction coefficients are lower. From a strictly electrostaticpoint of view, compounds that have higher Z/r, i. e. a higher cationscreening, show a higher near surface electronic density allowingbetter electrostatic repulsion of the tribologic counterpart. Thesecompounds are considered as lubricious oxides in the tribologyliterature. Here, we extend the crystal chemistry approach byapplying the model to oxide and nitride systems and also by adoptingthe charge density, located at cationic centers, instead of the so farused valence number for Z. According to data in the literature [18–20],Z/r is 2.03 for Si3N4 and 3.59 for SiO2 and therefore the low-loadfriction coefficient of partially oxidized Si3N4 films should be lowerthan that of non-oxidized ones, in good agreement with the presentexperimental results. The ionic potentials calculated here are lowerthan previous ones [7], owing to the absolute values of the useddensity charges being lower than the valence numbers. Besideschemical interactions, surface roughness can also be responsible forthe friction behavior (see Fig. 4). However, the influence of increasingsurface roughness with oxidation annealing in friction coefficient isnegligible at the lowest normal load (5 mN), due to the reducedcontact area as the result of the small number of asperity contacts.After OA, the formation of the oxynitride layer SiOxNy with low shearstrength on the top of the Si3N4 thin film may result in a low friction
d indentation curves at normal loads of 5, 10, and 20 mN (a). SEM image of a wear track).
4531J. Filla et al. / Surface & Coatings Technology 205 (2011) 4528–4531
coefficient. Thus, the friction behavior at 5 mN for both the untreatedand OA treated samples can be explained by the crystal chemicalmodel.
4. Conclusions
In summary, Si3N4 thin films were deposited on Si at differentsubstrate temperatures. Nanoindentation and low-load sliding ex-periments were performed in order to study the hardness and frictionbehavior before and after oxygen annealing in O2, trying to simulatehigh temperature oxidation by atmospheric oxygen in workingconditions. Si3N4 has a high oxidation resistance, such that a verythin oxide layer, approximately 10 nm thick, is obtained at 1000 °Cand 4 h of OA. The presence of such partially oxidized layer decreasesthe friction coefficient at low loads even when a higher surfaceroughness is observed. The crystal chemistry approach was expandedhere to calculate the ionic potentials (Z/r ratio) in oxides and nitrides(SiO2 and Si3N4), adopting the charge density, located at cationiccenters, instead of the so far used valence number for Z. The higherionic potential of SiO2 as compared to that of Si3N4 indicated that,according to the present approach, the friction coefficient of partiallyoxidized Si3N4 films should decrease after oxidation, in agreementwith the experimental results shown above. In dry cutting ormachining conditions, Si3N4 films retain their hardness. Furthermore,at the high surface temperatures developed during drymachining, theatmospheric oxygen renews the oxidation of the surface of the Si3N4
coating, decreasing the friction coefficient of the tribosystem and,finally, preventing further mechanical damage. Finally, we recall herethe very low values for the friction coefficient at a normal load of5 mN, which were obtained after thermal annealing in O2.
Acknowledgments
This work was partially sponsored by CNPq: projects # 573628/2008-4 (National Institute of Surface Engineering) and # 550316/2007-8 (Young Researcher). IJRB and CAF are CNPq fellows.
References
[1] J. Gerth, M. Larsson, U. Wiklund, F. Riddar, S. Hogmark, Wear 266 (2009) 444.[2] G.S. Fox-Rabinovich, K. Yamamoto, B.D. Beake, A.I. Kovalev, M.H. Aguirre, S.C.
Veldhuis, G.K. Dosbaeva, D.L. Wainstein, A. Biksa, A. Rashkovskiy, Surf. Coat.Technol. 204 (2010) 3425.
[3] Y.C. Chim, X.Z. Ding, X.T. Zeng, S. Zhang, Thin Solid Films 517 (2009) 4845.[4] S.H. Li, V. Palekar, Tribology 3 (2009) 132.[5] R.J. Cannara, M.J. Brukman, K. Cimatu, A.V. Sumant, S. Baldelli, R.W. Carpick,
Science 318 (2007) 780.[6] B. Bhushan, J.N. Israelachvili, U. Landman, Nature 374 (1995) 607.[7] A. Erdemir, Surf. Coat. Technol. 200 (2005) 1792.[8] A. Erdemir, S. Li, Y. Jin, Int. J. Mol. Sci 6 (2005) 203.[9] A. Ziegler, J.C. Idrobo, M.K. Cinibulk, C. Kisielowski, N.D. Browning, R.O. Ritchie,
Science 306 (2004) 768.[10] Y. Toivola, J. Thurn, R.F. Cook, J. Appl. Phys. 94 (2003) 6915.[11] S. Veprek, M.G.J. Veprek-Heijman, R. Zhang, J. Phys. Chem. Sol. 68 (2007) 1161.[12] Q.F. Fang, Q. Liu, S.Z. Li, Z.S. Li, P. Karvankova, M. Jilek, S. Veprek, Mater. Sci. Eng. A
442 (2006) 328.[13] C. Aguzzoli, C. Marin, C.A. Figueroa, G.V. Soares, I.J.R. Baumvol, J. Appl. Phys. 107
(2010) 073521.[14] L.C. Feldman, J.W. Mayer, S.T. Picraux, Materials Analysis by Ion Channeling,
Academic Press, New York, 1982.[15] W.C. Oliver, G.M. Pharr, J. Mater. Res. 7 (1992) 1564.[16] I.J.R. Baumvol, Surf. Sci. Rep. 36 (1999) 1.[17] R.P. Pezzi, P.L. Grande, M. Copel, Surf. Sci. 601 (2007) 5559.[18] Z. Liu, S. Sugata, K. Yuge, M. Nagasono, K. Tanaka, J. Kawai, Phys. Rev. B 69 (2004)
035106.[19] G.L. Zhao, M.E. Bachlechner, Phys. Rev. B 58 (1998) 1887.[20] R.E. Smallman, R.J. Bishop, Modern Physical Metallurgy & Materials Engineering,
6th ed., Butterworth-Heinemann, Oxford, 1999.
ANEXO 6
Appl Phys A (2009) 94: 263–269DOI 10.1007/s00339-008-4758-x
Atomic transport and chemical reaction in TiN/Ti nanolayerson plasma nitrided steel
C. Aguzzoli · E.K. Tentardini · C.A. Figueroa ·C. Kwietniewski · L. Miotti · I.J.R. Baumvol
Received: 7 March 2008 / Accepted: 28 May 2008 / Published online: 4 July 2008© Springer-Verlag 2008
Abstract Transport of N, O, and Ti during dc magnetronsputtering deposition of nanoscopic TiN/Ti and TiN struc-tures on plasma nitrided M2 tool steel, as well as transportof metallic species composing the plasma nitrided steel sub-strates were investigated. N and O depth distributions weredetermined with subnanometric resolution using narrow res-onant nuclear reaction profiling, whereas Ti was profiled,also with subnanometric depth resolution, by medium en-ergy ion scattering. The surface elementary compositionsof the TiN/Ti/nitrided steel and TiN/nitrided steel structureswere determined by low energy ion scattering. The chemi-cal compounds formed during deposition were accessed byX-ray photoelectron spectroscopy, indicating the presenceof TiN, TiO2, Ti oxynitrides, as well as other metallic ni-trides and oxynitrides, but no metallic Ti was observed. Ow-ing to the observed intensive atom mobility, the composi-tions of the deposited films on plasma nitrided steel struc-tures varied continuously on a nanoscopic scale, from thecore of the steel substrate to the bulk of the stoichiomet-ric TiN films. The Ti interlayer assists interdiffusion of allspecies, in contrast to the TiN film layer, which is known tobe a diffusion barrier. The improved adhesion of TiN hard
C. Aguzzoli · E.K. Tentardini · C.A. FigueroaUniversidade de Caxias do Sul, CCET, Av. Francisco G. Vargas1130, 95070-560 Caxias do Sul RS, Brazil
C. KwietniewskiPrograma de Pós-Graduação em Engenharia de Minas,Metalúrgica e de Materiais—PPGEM, Universidade Federaldo Rio Grande do Sul, 91501-970 Porto Alegre RS, Brazil
L. Miotti · I.J.R. Baumvol ()Instituto de Fisica, Universidade Federal do Rio Grande do Sul,91501-970, Porto Alegre RS, Brazile-mail: israel@if.ufrgs.br
coatings to plasma nitrided steel under working conditionsis discussed in terms of the gradual compositional changearound the interfaces and the atomic mobility during theirformation.
PACS 68-35.Fx · 68.35-p · 65.55-a
1 Introduction
Steels to manufacture cutting tools, dies, and moulds repre-sent a significant part of fabrication processing cost in metaldie-casting, stamping, forging, and forming, as well as inglass or plastic molding. Therefore, surface engineering byeither nitriding or nitrocarburasing of the tool steel and de-position of protective coatings are preferred alternatives to acomplete replacement of the tool, die, or mould [1, 2]. Theengineered surfaces must satisfy a range of specific mechan-ical characteristics, such as high hardness, wear and corro-sion resistance and many others [3]. Further requirementsare established by the characteristics of the process, such asnon-wettability (chemical inertness) with the processed ma-terial, stresses accommodation during processing, and ad-herence and compatibility with the steel matrix in workingconditions [2, 4]. In particular, adhesion to steel substratesconstitutes a critical requirement for the practical use of thinfilm protective coating technology [5, 6].
The synergism between plasma nitriding of steel and de-position of hard coatings like Ti, Cr, V, (Ti,Al), (Cr,Al)nitrides or carbides, so-called duplex processing, has beenwidely used in the last ten years to extend the service life ofcomponents and tools [7–11]. Indeed, bright plasma nitrid-ing (no compound layer) of steel produces a hard diffusionzone which provides a more gradual transition in hardnessand residual stresses between the hard coating and the sub-strate. Besides increasing load support, plasma nitriding pro-
264 C. Aguzzoli et al.
duces a more chemically suitable substrate for coating depo-sition [12], having a markedly positive influence on coatingadhesion. Furthermore, an “adhesion layer”, a thin film of Tior Cr, is commonly deposited on the nitrided steel surface toenhance the adhesion of the coating to the substrate [13].
Although well known and commonly used in industry,there are very few atomic scale investigations of the under-lying physico–chemical reasons for the adhesion improve-ment provided by the above mentioned duplex process orintermediate metallic layer, as well as on the joint effects ofthese two major surface engineering “architecture” improve-ments.
Aiming at a better understanding of the determinant fac-tors of hard coating adhesion to nitrided steel, we report hereon atomic transport and chemical reaction investigations innanoscopic TiN film structures deposited in usual indus-trial conditions, with or without an intermediate Ti layer, onbright plasma nitrided high-speed AISI M2 steel. Since thenear-interface structure, composition, and interactions con-stitute the intrinsic origin of adhesion, the present investiga-tion can help to establish correlations between the determin-ing factors, leading to optimization of materials and process-ing routes for steel surface engineering.
2 Experimental
The samples of the present work were either TiN–Ti bilay-ered films with a total thickness of 10 nm (nominally 5 nmTiN and 5 nm Ti) or TiN films with the same total thick-ness, deposited on bright plasma nitrided AISI M2 steel. DCbright plasma nitridation was carried out in 300 Pa of a 95/5H2/N2 gas mixture, keeping the steel substrate at 450°C, pre-viously cleaned by sputter-etch in H2/Ar plasma. The filmswere deposited by dc magnetron sputtering from a pure Titarget either in Ar or in Ar/N2 plasma, always at a totalpressure of 3 × 10−1 Pa. The base pressure in the cham-ber was in the ultra-high vacuum region (10−6 Pa). Nitro-gen gas used for both plasma nitriding and film depositionwas either pure, natural N2 or N2 enriched to 99% in the15N isotope (15N2). The substrate temperature during de-position was 450°C. Three sets of samples were then pro-duced, following different routes: (i) plasma nitriding of thesteel substrates in 15N2, followed by film depositions in nat-ural N2; (ii) plasma nitriding of the steel substrates in naturalN2, followed by film depositions in 15N2; (iii) plasma nitrid-ing of the steel substrate in natural N2, followed by 10 keV15N+ implantation into the nitrided substrate to a dose of2 × 1016 cm−2, annealing at 450°C for 60 min, and film de-positions in natural N2. The TiN and Ti films used here weremade intentionally much thinner than those of practical use,in order to allow for investigation of the depth distributionof atomic species and of chemical compounds around the in-terfaces [13]. Nitrogen and oxygen profiles were determinedwith subnanometric depth resolution by narrow resonant nu-
clear reaction profiling (NRP) [14, 15]. Titanium profilingwas accomplished, also with subnanometric depth resolu-tion, by medium energy ion scattering (MEIS) [16]. Lowenergy ion scattering (LEIS) [17], was used to access theelementary composition of the outermost surfaces. Chemi-cal analysis was accomplished by X-ray photoelectron spec-troscopy (XPS). An Al Kα (1486.6 eV) X-ray source wasused.
3 Results and discussions
In order to control the mechanical and tribological character-istics of the present films, 2 µm thick TiN coatings depositedin identical conditions of those used in the present work onplasma nitrided AISI M2 steel, having a 0.1 µm thick Ti in-terlayer coatings were produced. Nanohardness and Youngmodulus were determined and the results confirmed those ofmany previous reports, namely nanohardness (H) of around24 GPa and a Young modulus (E) of around 220 GPa. Thisgives a H/E ratio of 0.11. The hardness to Young modu-lus (H/E) ratio, so called elastic strain to failure, has beenproposed and consistently used [18–20] to evaluate the resis-tance to plastic deformation of thin film coatings and to pre-dict their resistance to wear. Thus, a high H/E ratio valueindicates a high resistance of the coating to plastic deforma-tion and, presumably, a high wear resistance as well, besidesof low stiffness [18–20]. The figure of H/E = 0.11 obtainedhere indicates good wear resistance for the present coatings.
Although specific adhesion determination was not ac-complished in this work, very recently several authors ad-dressed the adhesion of thick reactive sputtered-depositedTiN coatings of plasma nitrided tool steel, with or without aTi interlayer. The role of a Ti intermediate layer in increas-ing the adhesion was investigated [20–23], revealing thatnot only the presence of the Ti interlayer itself is important,but also the gradual variation of its composition, from theTiN/Ti interface to the Ti/nitrided steel interface. In the samelines, the role of the plasma nitrided layer of the steel wasdetermined [5, 24], indicating that an increased load supportand gradual composition changes around the interfaces con-tribute significantly to increase the adhesion of the coatingin working conditions.
Figure 1(a) shows the Rutherford backscattering spec-trum (RBS) obtained for a 20 nm thick TiN film depositedin the above described conditions on pure-C (graphite) sub-strate, avoiding thus the overlap with backscattering signalsfrom heavier metallic elements. The spectrum in Fig. 1(a)confirms the TiN average stoichiometry, showing also asmall signal at a backscattering energy corresponding tooxygen in the film (≤1 × 1015 O cm−2), showing two peakswhich can be associated with near surface and near interfaceregions of the film, with a clear O depletion in the bulk. Oxy-gen profiling was also accomplished here using NRP. Fig-
Atomic transport and chemical reaction in TiN/Ti nanolayers on plasma nitrided steel 265
Fig. 1 (a) Rutherford backscattering spectrum of 2 MeV He+ incidentparticles at 60° tilt in a 20 nm TiN film on a pure C (graphite) sub-strate. The inset shows the oxygen region of the backscattering spec-trum. (b) Excitation curve of the 18O(p,α)15N nuclear reaction aroundthe resonance at 151 keV for the same sample. The solid line representsthe simulation of the experimental spectrum (solid squares) assumingthe O profile shown in the inset
ure 1(b) shows the excitation curve of the 18O(p,α)15N nu-clear reaction around the narrow (R ≈ 100 eV) resonanceat 151 keV. The oxygen profile assumed to simulate the exci-tation curve [14, 15], after correcting for the natural isotopicabundances of 16O and 18O, is shown in the inset. The muchbetter depth resolution of this method (0.7 nm as comparedto 10 nm for RBS) confirms the surface and interface peakconcentrations of O and the much smaller concentration ofoxygen in the bulk of the film.
The excitation curves of the 15N(p,αγ )12C nuclear reac-tion around the narrow (R ≈ 120 eV) resonance at 429 keVfor the TiN/Ti/nitrided steel and TiN/nitrided steel structuresprepared in the three routes described above are shown inFig. 2. The 15N concentration profiles assumed for the sim-ulation [14, 15] of the excitation curves are also shown, re-vealing significant migration of N during deposition. The15N profiles for route (i) evidence that the propagating 15Nfronts from the nitrided steel substrates into the films reach
the outermost surfaces. For route (ii), nitrogen from thedeposited films migrates into the nitrided steel substrateduring deposition, the 15N concentrations being larger inTiN/nitrided steel than in TiN/Ti/nitrided steel. The exci-tation curves and 15N profiles determined for samples pre-pared in route (iii) confirm entirely the qualitative picturerevealed for route (i), showing in addition larger concentra-tions of 15N in the deposited films for the TiN/Ti structuresthan for the TiN one. Thus, the Ti interlayer constitutes afast diffusion region that assists the migration of N into thefilm structure. In the case of route (i), this effect is over-come by the infinite source of 15N constituted by the 15N-nitrided steel layer (≈20 µm), leading to saturation of the15N content in the films. Thus, isotopic substitution makesevident high nitrogen interdiffusion during TiN/Ti and TiNthin film deposition [25] on nitrided steels at the substratetemperature of 450°C, which is standard in production forgood coating adhesion. The range of N migration from thefilms into the nitrided steel is approximately 20 to 30 nm,whereas N from the nitrided substrate has a minimum mi-grating range comparable to the film thickness.
Typical N 1s and O 1s photoelectron regions for TiN/Tiand TiN films on nitrided steel are shown in Fig. 3. In theTiN/Ti/nitrided steel nanostructure (Fig. 3(a), solid line),the most intense photoelectron components of the N 1s
signal are assigned to N bonded in metallic nitrides suchas TiN, CrN, and FeNx , [26], with a less intense compo-nent assigned to N in metallic oxynitrides (TiNO, CrNO,and FeNO) [27]. For the TiN/nitrided steel nanostructure(Fig. 3(a), dashed line), on the other hand, TiN is the mostimportant component among the metallic nitrides, whereasthe spectral area assigned to titanium oxynitride is rela-tively more significant than for the TiN/Ti nanostructure.The O 1s signal from the TiN/Ti/nitrided steel nanostructure(Fig. 3(b), solid line) has a dominant component assigned toO in TiO2, which cannot in fact be distinguished from CrOx
and FeOx , as well as a smaller component assigned to O intitanium oxynitrides. For the TiN/nitrided steel nanostruc-ture (Fig. 3(b), dashed line), on the other hand, the (O inoxide)/(O in oxynitride) intensity ratio decreases substan-tially. It seems then that the Ti interlayer favors the forma-tion of metallic oxides (TiO2, CrOx , and FeOx) and oxyni-trides (TiNO, CrNO, and FeNO), in detriment to TiN. TheTi 2p regions shown in Fig. 3(c) present photoelectron com-ponents corresponding to TiN, TiON, and TiO2 compounds[28], but no evidence of metallic Ti is observed.
The Ti distribution in depth was determined, with a typi-cal 0.5 nm depth resolution, by MEIS using 100 keV H+ in-cident ions. For the MEIS analysis, single crystalline Si(001)substrates (C–Si) were used to deposit the films, since Fe,Cr. Mo, W from the steel substrate would shadow almostentirely the Ti signal in the spectra. On the other hand, thediffusivity of Ti in C–Si at 450°C is much smaller than in
266 C. Aguzzoli et al.
Fig. 2 Excitation curves of the 15N(p,αγ )12C nuclear reac-tion around the resonance at 429 keV and 15N profiles for theTiN(5 nm)/Ti(5 nm) (solid squares, dashed lines) and TiN(10 nm)(empty circles, dotted lines) nanostructures on: (a) and (b) plasmanitrided M2 steel in 15N2; (c) and (d) Ti15N(5 nm)/Ti(5 nm) andTi15N(10 nm) films on plasma nitrided tool steel; (e) and (f) plasma
nitrided steel substrate in natural N2, followed by 15N+ implantation(10 keV, 2 × 1016 cm−2), annealing at 450°C for 60 min, and film de-positions in natural N2. The solid lines represent the excitation curvefor a Si315N4 sample, giving the energy position corresponding to 15Nat the surface
Atomic transport and chemical reaction in TiN/Ti nanolayers on plasma nitrided steel 267
Fig. 3 X-ray photoelectron spectra of TiN(5 nm)/Ti(5 nm) (solidlines) and TiN(10 nm) (dashed lines) films on plasma nitrided M2 steel:(a) N 1s photoelectrons, (b) O 1s photoelectrons, and (c) Ti 2p photo-electrons. The dashed vertical lines represent the approximate bindingenergies for individual compound components
M2 steel [10, 29, 30] and therefore any effect observed hereis just a lower limit for the real migration of Ti from thefilms into M2 steel. Figure 4(a) shows the MEIS spectra forthe as-deposited TiN/Ti/Si nanostructure with the substratesat 450°C (solid triangles) and for the same structure afterannealing at 550 and 650°C (solid line and empty circles,respectively). There is no noticeable transition in the spectra
Fig. 4 (a) Medium energy ion scattering spectra of 100 keV incidentH+ ions on TiN(5 nm)/Ti(5 nm) and TiN(10 nm) films on Si at 450°Csubstrate temperature (solid triangles) and after annealing at 550 and650°C (solid line and empty circles, respectively). (b) Low energy ionscattering spectra of 1 keV incident He+ ions on TiN(5 nm)/Ti(5 nm)and TiN(10 nm) films on plasma nitrided M2 steel (empty circles andsolid lines, respectively)
between the TiN and Ti regions because the atomic concen-trations of Ti in both materials are very similar. The simula-tion of these spectra reveals a rather sharp interface betweenthe as-deposited structure and the Si substrate. However, byheating at 550 and 650°C, one notices a clear migration ofTi into the substrate. Considering that: (i) temperatures be-tween 550 and 650°C are commonly reached at work by thesurface of the coated engineering components in most ap-plications and (ii) the results here presented are just a lowerlimit for Ti migration into the substrate, one can say thatthere is an effective transport of Ti from the TiN/Ti struc-tures into the nitrided steel, although probably smaller thanN transport. In the temperature range used here for heatingthe TiN/Ti/Si samples, titanium silicide formation at the in-terface cannot be disregarded, although there are no bumpsor plateaux in the MEIS spectra that would indicate any sep-arate phase layer. Finally, Fig. 4(b) shows the LEIS spectra
268 C. Aguzzoli et al.
for 1 keV incident He+ ions on TiN/Ti/nitrided steel (emptycircles) and TiN/nitrided steel (solid line) nanostructures.LEIS is a surface selective technique and therefore the spec-tra in Fig. 4(b) describe the elementary composition of theoutermost surface of the samples. The presence of O andTi and the absence of N in both spectra reveal that, at thesurface of the TiN films, N was completely exchanged forO during exposure to air. The most striking feature, how-ever, was the presence at the film surface of Fe, Cr, Mo, Si,and W which are the elements with higher concentration inthe M2 tool steel substrate. Moreover, one notices that thesurface concentration of these elements is much larger forthe TiN/Ti than for the TiN nanostructure. One could pos-sibly attribute the presence of these elements in the spectrato non-homogeneous films presenting voids or holes that ex-pose the steel substrate directly to the He+ beam. This wasruled-out by atomic force microscopy and X-ray reflectom-etry (results not shown here) that revealed that the films didcover homogeneously the steel surface.
4 Conclusions
In this work we found that during TiN film deposition onplasma nitrided tool steel in usual industrial conditions, withor without an intermediate Ti interlayer, there is a pro-nounced transport of N and Ti atoms from the film into thesteel substrate, as well as transport of N and metallic speciesfrom the substrate into the growing nanoscopic film struc-ture.
The interfacial regions of these hard coating/nitrided steelstructures are thus formed under intensive atomic mobility,having consequently a complex composition. In fact, in ananoscopic scale, the composition varies continuously fromthe core of the steel substrate to the bulk of the stoichiomet-ric TiN hard coating. Interface stress originated in abruptchanges in composition is thus relaxed by the gradual com-positional change and by the strong atomic mobility dur-ing interface formation. This can respond for the excellentadhesion of TiN hard coatings to plasma nitrided steel un-der working conditions. Furthermore, gradual compositionalchange and strong atomic mobility during deposition reducealso lattice mismatches and incomplete chemical bonding inthe near interface region, thus contributing also to improvethe adhesion of the films to the substrates.
Plasma nitriding of steel before TiN/Ti film depositionpromotes the formation of Ti (and probably Fe, Cr, and Si aswell) nitrides around the film/substrate interface, which alsocontribute to the increasing of adhesion owing to strongerchemical bond between coating and substrate. The Ti in-terlayer assists interdiffusion of all species, in contrast tothe TiN film layer, which is known to be a diffusion bar-rier. On the other hand, the Ti interlayer favors the forma-
tion of metallic oxides (TiO2, CrOx , and FeOx), and oxyni-trides (TiNO, CrNO, and FeNO) in detriment to TiN andtherefore its thickness must be limited, which is the case inall practical applications. The whole (nanoscopic) Ti inter-layer is seen to be converted into Ti oxide and oxynitrides,as no metallic Ti is observed, whereas the near surface re-gion of the TiN coating is seen to be oxidized when exposedto air. This oxide layer at the surface has a lubricating ef-fect at work and it is continuously renewed as wear removesthe oxidized layer, exposing fresh TiN to air at high surfacetemperatures.
References
1. E. Bemporad, M. Sebastiani, C. Pecchio, S. De Rossi, Surf. Coat.Technol. 201, 2155 (2006)
2. J. Lin, S. Carrera, A.O. Kunrath, D. Zhong, S. Myers, B. Mishra,P. Ried, J.J. Moore, Surf. Coat. Technol. 201, 2930 (2006)
3. A. Alsaran, A. Çelik, M. Karakan, Mater. Charac. 54, 85 (2005)4. E.K. Tentardini, C. Aguzzoli, M. Castro, A.O. Kunrath, J.J.
Moore, I.J.R. Baumvol, Thin Solid Films 516, 3062 (2008)5. T. Ono, M. Uemura, M. Yatsuzuka, Nucl. Instrum. Methods Phys.
Res., Sect. B 257, 786 (2007)6. J.H. Huang, C.H. Ma, H. Chen, Surf. Coat. Technol. 201, 3199
(2006)7. I. Zukerman, A. Raveh, H. Kalman, J.-E. Klemberg-Sapieha, L.
Martinu, Wear 263, 1249 (2007)8. S.Y. Lee, Surf. Coat. Technol. 193, 55 (2005)9. K.S. Klimek, A. Gebauer-Teichmann, P. Kaestner, K.T. Rie, Surf.
Coat. Technol. 201, 5628 (2006)10. J.L. He, K.C. Chen, A. Davison, Surf. Coat. Technol. 200, 1464
(2005)11. N.J.M. Carvalho, J.Th.M. De Hosson, Acta Mater. 54, 1857
(2006)12. F. Kieckow, C. Kwietniwski, E.K. Tentardini, A. Reguly, I.J.R.
Baumvol, Surf. Coat. Technol. 201, 3066 (2006)13. J.H. Huang, F.Y. Ouyang, G.P. Yu, Surf. Coat. Technol. 201, 7043
(2007)14. I. Vickridge, G. Amsel, Nucl. Instrum. Methods Phys. Res., Sect.
B 45, 6 (1990)15. I.J.R. Baumvol, Surf. Sci. Rep. 36, 1 (1999)16. R.P. Pezzi, P.L. Grande, M. Copel, G. Schiwietz, C. Krug, I.J.R.
Baumvol, Surf. Sci. 601, 5559 (2007)17. H.H. Brongersma, M. Draxler, M. de Ridder, P. Bauer, Surf. Sci.
Rep. 62, 1 (2007)18. S.K. Ghosh, P.K. Limaye, B.P. Swain, N.L. Soni, R.G. Agrawal,
R.O. Dusane, A.K. Grover, Surf. Coat. Technol. 201, 4609 (2007)19. D. Galvan, Y.T. Pei, J.Th.M. de Hosson, Surf. Coat. Technol. 201,
590 (2006)20. A.A.C. Recco, I.C. Oliveira, M. Massi, H.S. Maciel, A.P.
Tschiptschin, Surf. Coat. Technol. 202, 1078 (2007)21. J. Gerth, U. Wiklund, Wear 264, 885 (2008)22. J.-H. Huang, C.-H. Ma, H. Chen, Surf. Coat. Technol. 201, 3199
(2006)23. K.S. Klimek, H. Ahn, I. Seebach, M. Wang, K.-T. Rie, Surf. Coat.
Technol. 174, 677 (2003)24. E. Bemporad, M. Sebastiani, C. Pecchio, S. De Rossi, Surf. Coat.
Technol. 201, 2155 (2006)25. K.M. Egland, J. Mazumder, Acta Mater. 55, 3623 (2007)26. O. Nishimura, K. Yabe, M. Iwaki, J. Electron Spectrosc. Relat.
Phenom. 49, 335 (1989)27. B. Folkesson, Acta Chem. Scand. 27, 287 (1973)
Atomic transport and chemical reaction in TiN/Ti nanolayers on plasma nitrided steel 269
28. J. Guillot, J.M. Chappé, O. Heintz, N. Martin, L. Imhoff, J.Takadoum, Acta Mater. 54, 3067 (2006)
29. W.S. Baek, S.C. Kwon, J.Y. Lee, S.R. Lee, J.J. Rha, K.S. Nam,Thin Solid Films 323, 146 (1998)
30. L. Yanping, X. Jinyong, K. Xiaoyun, W. Jianzhong, G. Yuan, X.Zhong, Z. Guangqiu, G. Yuanjing, Z. Yuefei, Plasma Sci. Technol.8, 213 (2006)