Reservatório
1
For More Information (800) 848-1750 www.osmonics.com SANITARY DESIGN In-Line, 1 Round, 222 DRAIN: 1/2" CF 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.0 10.0 20.0 30.0 40.0 50.0 60.0 Typical Water Flow Rate gpm psid Element Length 05 - inch: 9.3" (23.6 cm) 7.8" (19.8 cm) 15.6" (39.6 cm) 10 - inch: 14.3" (36.3 cm) 12.8" (32.5 cm) 27.3" (69.3 cm) 20 - inch: 24.3" (61.7 cm) 22.8" (57.9 cm) 59.3" (150.6 cm) 30 - inch: 34.3" (87.1 cm) 32.8" (83.3 cm) 67.3" (170.9 cm) 40 - inch: 44.3" (112.5 cm) 42.8" (108.7 cm) 87.3" (221.7 cm) (A) Overall Height (B) Shell Height (C) Minimum Distance Required to Remove Shell C B A 3.50 OD 3.33 ID INLET: 1 1/2" CF VENT: 1/2" CF CLAMP CARTRIDGE CONNECTION FOR CODE-8 (-222) CONNECTION SHELL GASKET DRAIN: 1/2" CF OUTLET: 1 1/2" CF BASE Ordering is easy when you follow the Model Number Builder below. Reading from left to right, select which specifications you require and fill in the box with the code for that option. The end result will be a 13 digit model number. Building a Model Number A San. Valve B 1 / 2" Ferrule C 1 1 / 2" Gage Port/ San. Valve D 1 1 / 2" Gage Port/ 1 / 2" TC E San.Valve/NoVent F 3 / 8" VCR G 1 / 2" TC/No Vent H No Vent/Drain C 1 1 / 2" Ferrule D 1 1 / 2" Butt Weld 1 10" 2 20" 3 30" 4 40" 5 05" 8 222 1 20Ra/ 32Ra/ EP 2 10Ra/ 32Ra/ EP H H/D Clamp N No jacket 1 Non-Code E EPDM S Silicone V Viton VT PTFE Encap. Viton B Buna ST PTFE Encap. Silicone This portion of the model is already completed for you. SN = Sanitary Design 2 = In-Line A = 1 Round (3.5”) Element Length Cartridge Connection Inlet/Outlet Connection Vent/Drain Connection ID/OD Finish Closure Type Jacket Configuration ASME Code Gasket Material 8 H N 1 SN 2 A
-
Upload
david-montezano -
Category
Engineering
-
view
39 -
download
1
Transcript of Reservatório
For More Information (800) 848-1750 www.osmonics.com
SANITARY DESIGN In-Line, 1 Round, 222
DRAIN: 1/2" CF
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.0 10.0 20.0 30.0 40.0 50.0 60.0
Typical Water Flow Rate
gpm
psid
ElementLength
05 - inch: 9.3" (23.6 cm) 7.8" (19.8 cm) 15.6" (39.6 cm)10 - inch: 14.3" (36.3 cm) 12.8" (32.5 cm) 27.3" (69.3 cm)20 - inch: 24.3" (61.7 cm) 22.8" (57.9 cm) 59.3" (150.6 cm)30 - inch: 34.3" (87.1 cm) 32.8" (83.3 cm) 67.3" (170.9 cm)40 - inch: 44.3" (112.5 cm) 42.8" (108.7 cm) 87.3" (221.7 cm)
(A) Overall Height
(B) Shell Height
(C) Minimum Distance Required to Remove Shell
C
B
A3.50 OD 3.33 ID
INLET: 1 1/2" CF
VENT: 1/2" CF
CLAMP
CARTRIDGE CONNECTIONFOR CODE-8 (-222)CONNECTION
SHELL
GASKET
DRAIN: 1/2" CF
OUTLET: 1 1/2" CF BASE
Ordering is easy when you follow the Model Number Builder below. Reading from leftto right, select which specifications you require and fill in the box with the code for thatoption. The end result will be a 13 digit model number.
Building a Model Number
A San. ValveB 1/2" FerruleC 11/2" Gage Port/
San. ValveD 11/2" Gage Port/
1/2" TCE San.Valve/NoVentF 3/8" VCRG 1/2" TC/No VentH No Vent/Drain
C 11/2" FerruleD 11/2" Butt
Weld
1 10"2 20"3 30"4 40"5 05"
8 222 1 20Ra/32Ra/EP
2 10Ra/32Ra/EP
H H/D Clamp
N No jacket 1 Non-Code E EPDMS SiliconeV Viton
VT PTFEEncap.Viton
B Buna
ST PTFEEncap.Silicone
This portion of themodel is already completed for you.
SN = SanitaryDesign
2 = In-LineA = 1 Round (3.5”)
ElementLength
CartridgeConnection
Inlet/OutletConnection
Vent/DrainConnection
ID/ODFinish
ClosureType
JacketConfiguration
ASMECode
GasketMaterial
8 H N 1SN 2 A
![Fluxo Radial No Reservatório Ipr[1].](https://static.fdocumentos.tips/doc/165x107/563db7bd550346aa9a8d80e3/fluxo-radial-no-reservatorio-ipr1.jpg)
